We will reply to your message within an hour.
More
These nozzles produce a flat, thin spray pattern. They're good for general cleaning, washing, etching, foam control, and applying coatings.
The spray is deflected at a steep angle to produce a low-impact, extra-wide spray.
A check valve prevents the nozzle from dripping when it is turned off. Spray tips can be removed for cleaning and replacement.
Drill a hole anywhere along a pipe and snap on these nozzles. Spray tips can be quickly and easily removed for cleaning and replacement.
These nozzles have replaceable tips that are removable with a quarter-turn.
Spray is deflected at a narrow angle to create the highest impact of all our flat spray nozzles.
A quick-disconnect hose fitting on these nozzles means you can remove and replace them easily to change spray patterns and angles.
A low flow rate makes these nozzles good for distributing fluids, cooling, washing, and rinsing.
Particles in liquid won’t clog these nozzles because of their unique internal and external design.
These nozzles project their spray at a right angle from their threaded connection.
Spray a precise, concentrated, high-velocity stream longer distances than other spray patterns to handle tough cleaning applications.
The large square coverage area makes these nozzles a good choice for chemical processing as well as for cooling applications.
Save time in applications where you often need to replace worn nozzles. These nozzles consist of a base and a nozzle, so you can replace the tip with just a quarter turn.
With a unique internal and external design, these nozzles let particles in liquid pass through instead of clogging.
By circulating their spray, these nozzles clean faster with more even coverage and less water than stationary tank-washing nozzles.
Internal gears create controlled motion as fluid moves through these nozzles, maintaining speed and producing large droplets to efficiently clean heavily soiled or large-diameter tanks.
Use these nozzles with detergent that’s diluted in water to create a rotating, multi-directional foam spray for effectively rinsing tanks, drums, and small vessels.
To effectively rinse tanks, drums, and small vessels, these nozzles spray in multiple directions.
Certified by 3-A to meet sanitary design standards, these nozzles have a 360° spray pattern to effectively rinse tanks and vessels in food, beverage, and pharmaceutical environments.
Avoid clogs while rinsing tanks, drums, and small vessels. These nozzles have a unique internal and external design, so particles in liquid pass through instead of getting stuck.
A wide spray angle provides a larger coverage area and produces a finer, more atomized spray than full-cone nozzles.
Mixing compressed air and liquid together, these nozzles create an ultra-fine, uniform spray without using high pressures. Also known as air-atomizing nozzles, they make droplets that are less than half the size of other fogging nozzles.
These nozzles provide a uniform distribution of droplets.
Fogging nozzles provide smaller, more atomized spray droplets than misting nozzles.
Create small, atomized spray droplets for cooling, moistening, and humidifying applications. These nozzles have a check valve that prevents dripping when they’re turned off
A check valve prevents the nozzle from dripping when it is turned off.
A unique internal and external design lets particles in liquid pass through instead of clogging, leading to higher volumes of mist.
These nozzles produce a flat, thin spray pattern.
Spray a precise, concentrated, high-velocity stream longer distances than flat spray nozzles to handle tough cleaning applications.
The superior cleaning ability of a solid stream has been combined with rotating spray action for excellent coverage.
No need to juggle multiple nozzles with different spray angles—just turn the cover to adjust the spray angle from 0° to 80°.
Push the nozzle out for lower pressures and pull it back for higher pressures. Turn the cover to adjust the spray angle from 0° to 25° or 75°.
Combining rotation with a solid stream, these nozzles spray in a 25° hollow cone shape to cover a wide area. They’re easy to remove thanks to their quick-disconnect hose connection.
Instead of swapping between nozzles, turn the cover on these nozzles to change their spray angle. They have quick-disconnect couplings for easy detachment.
No need to switch between nozzles—push these nozzles in and pull them out to change their pressure level, and twist their cover to adjust the spray angle between 0° and 40°. Their quick-disconnect hose connection makes attaching and removing them easy.
Specifically designed for steam, these nozzles direct steam better than standard spray nozzles.
FM approved for use in fire-protection applications, these nozzles produce a heavy, coarse spray to quickly put out fires.
The tapered tip is wider at the base and thinner at the tip, allowing this tool to clean out residue and dirt from nozzles, aeorsol spray heads, and other small openings of various sizes, allowing for an even spray.
These premium nozzles are engineered for the most efficient airflow consumption.
Also known as air-shield and safety-shield nozzles, a center airstream blows away debris while an outer air curtain deflects flying chips and dust.
Attach to your blowgun to direct airflow.
Made from rubber, these nozzles won’t scratch or damage sensitive workpieces.
Control consumption and noise by adjusting the airflow.
Extend these telescoping nozzles to increase your reach.
The extra length allows access into hard-to-reach areas.
The flat nozzle tip distributes air over a wider area than focused-airflow nozzles.
Adjust airflow to control consumption and noise.
These nozzles are made of FDA-listed materials.
Air blows out of these flat nozzles in a wide pattern at a 90° angle from the inlet, distributing air over a wider area than focused-airflow nozzles. They’re FDA compliant 21 CFR 110.40 for use in the food industry.
At less than 2" long and with a wide airflow pattern, these nozzles are ideal for tight spaces where you need to distribute air over a wider area than a focused-airflow nozzle.
Air blows out of these nozzles at a right angle in a wide pattern, distributing air over a wider area than focused-airflow nozzles.
These needle-style nozzles force air to a precise pinpoint.
Focus air with pinpoint precision.
Blow air backward to clean out the inside of pipes, tubes, and channels without pushing debris into your system.
As compressed air flows through these nozzles, they rotate to efficiently and evenly blow off large areas.
Nozzles are attached to a flexible hose that bends and holds its shape until you reposition it.
The magnetic base mounts to your work surface and has a control valve for adjusting airflow.
Choose a base, hose, and nozzle for a custom setup.
Shaped to fit into extremely tight spaces, these nozzles can be used to remove parts from molds. Tap the wedge into position, attach the nozzle to a blowgun, and activate the airflow to release the part.
Convert your blowgun to a spray gun. These nozzles spray air and liquids at the same time.
Often used for simultaneously spot cooling and blowing parts, these nozzles cool compressed air without electricity or refrigerants.
Blow debris and sweep it away with the built-in brush.
Attach one of these swivels to an air nozzle to direct air 30° left, right, up, and down.
Turn your blowgun into a scraper to remove and blow away debris at the same time.
Compact enough to carry with you, these guns have a built-in quick-disconnect hose coupling for easy connection to an air line.
These blowguns have a metal body.
The lightweight plastic construction makes these blowguns more comfortable to hold than metal.
The rubber tip won't damage parts.
Designed to reduce noise, these blowguns are quieter than similar standard guns.
Also known as air-shield and safety-shield blowguns, a center airstream blows away debris while an outer air curtain deflects flying chips and dust.
Operate a blowgun without disconnecting your air tool—these guns fit between the tool and air hose. Good for blowing away debris after using an air-powered sander or grinder.
Two inlets allow connection to air lines above or below. Use the top inlet when the blowgun is suspended from an overhead hose and the bottom inlet for bench and floor hoses.
Connect the included hose to your air supply and these blowguns are ready to use.
The extra length lets you access hard-to-reach areas.
The included hose is ready to connect to your air supply.
The lightweight plastic body is more comfortable to hold than metal.
These guns include a rubber tip that won't damage your workpiece.
Also known as air-shield and safety-shield blowguns, an outer air curtain deflects flying chips and dust while the center airstream blows away debris.
Increase your reach with the telescoping nozzle.
Maximize comfort and minimize strain with these lightweight guns.
These blowguns provide more than two times the airflow of standard guns.
Air flows out of the side of the nozzle to clean air filters, radiators, and inside recesses.
Blow air backward from the nozzle to clean out the inside of pipes, tubes, and channels without pushing debris into your system.
The most powerful blowguns we sell, these use compressed air to clean and blow debris.
Clear dust and debris, test air ducts for leaks, and dry large surfaces without needing a compressed air line.
The flat nozzle distributes air over a wide area.
Also known as siphon guns, these spray air and liquids at the same time. Push the lever and the airflow creates suction that draws water, cleaning solution, or other liquids through the hose.
Clean surfaces without transferring dust or moisture from the air hose. These blowguns have a replaceable filter that traps particles such as rust and smoke and absorbs moisture.
Bend the stand's flexible arm to position your gun and keep it in place. Use the included foot pedal to activate airflow and static elimination.
These guns provide more than three times the airflow of standard static-eliminating blowguns.
Blow off dust and contamination, eliminate static charges, and guard against ESD (electrostatic discharge).
A nonconductive plastic nozzle and tip protect against accidental contact with live electrical circuits. These blowguns are tested to 1,000 volts to meet IEC 60900.
Safely blow dust and debris off your clothes. These blowers are a safer alternative to compressed air and help you meet OSHA regulations.
Launch foam cylinders through hose and tubing to power away dirt and deposits. Unlike cleaners with brushes, these work on flexible, curved, and coiled tubing as well as those with fittings, valves, and 90° bends.
Producing the same airflow as standard air knives, these are quieter and use 18% less compressed air.
Create a sheet of high-velocity air.
Also known as air wipes, these use a 360° airstream to blow off, dry, clean, and cool tubes, cables, extruded shapes, and hoses.
Attach to a blower for high-speed airflow at low pressure.
Dry and cool parts, wipe conveyor belts, control coating depth, and blow liquid, chips, and dust off of equipment in sanitary environments.
An ionizing bar temporarily neutralizes static to protect against ESD (electrostatic discharge).
These produce the same airflow as standard static-eliminating air knives but are quieter and use 15% less compressed air.
Sets include a focused nozzle for concentrated airflow, a flat-tip nozzle for heating wide surfaces, and a deflecting nozzle that protects adjacent surfaces from heating.
Shaped to hold round objects, use these nozzles for installing heat-shrink tubing and bending plastic pipe.
Create a wide airflow that’s good for drying and stripping paint.
Concentrate a heat gun's airflow.
Insert plastic welding rod through a second opening in the nozzle. It directs air to heat the rod and weld plastic.
A deflector protects adjacent areas from heating. The flat shape creates a wide airflow.
Replace blower wheels, cords, handles, and other components on heat guns.
Build a custom 1/4" system to deliver coolant, cutting oil, water, or air in any direction.
Kits contain lengths of hose, nozzles, valves, and caps.
Build a custom 1/2" system to deliver coolant, cutting oil, water, or air in any direction.
Build a custom 3/4" system to deliver coolant, cutting oil, water, or air in any direction.
Kit contains lengths of hose, nozzles, connectors, and assembly pliers.
Use with Loc-Line hose to assemble and disassemble components.
Use with Snap-Loc hose to assemble and disassemble components.
This hose is made of steel.
These nozzles handle coolant pressure up to 150 psi.
Use as a lever to adjust the angle of coolant streams.
For use in the highest pressure coolant lines, these nozzles are rated for at least 1,000 psi.
The most versatile of our machine-mount coolant nozzles, these adjust from a fine mist to a direct stream and can deliver coolant in any direction. Max. pressure is 100 psi.
For high-pressure coolant lines, these nozzles withstand pressure up to 500 psi.
Press these nozzles into unthreaded holes.
Draw coolant from your existing tank.
These dispensers have a reservoir for recirculating coolant.
These dispensers have a reservoir and controls for coolant flow.
Press the lever to stop coolant mist and start a high-velocity air stream to remove dust and shavings.
Deliver a small, controlled amount of coolant to a workpiece.
Snap these adapters into the ball-socket connections on CNC machines to connect threaded coolant hose and nozzles to coolant supply ports.
These durable wash guns are typically used for frequent washdowns and cleanup.
For light duty spray-down applications, attach these wash guns to any standard garden hose.
These wash guns have a high maximum pressure, so use them with pressure washers and high-pressure spray systems.
The powerful combination of air and water creates a high-velocity, atomized spray without needing high pressure. These guns also can be used to siphon.
Connect these guns to your garden hose and automatically dispense solution from the attached bottle instead of dragging around a siphon hose.
With a high maximum pressure and quick-disconnect nozzle connection, these wash guns work with pressure washers and high-pressure spray systems and it’s easy to swap out their nozzles.
Use these guns to clean as well as apply chemicals and solvents.
Clean hard-to-access areas by extending the reach of your quick-disconnect wash gun.
Combine the power of steam and detergent—siphon detergent from a drum and use the control panel to regulate the steam/detergent mixture and change the temperature and flow rate.
Clean and sanitize surfaces with the power of steam—with or without detergents and other chemicals.
Connect these cleaners to existing steam lines to remove dirt, grease, and heavy oils from most surfaces.
Use for cleaning small areas and devices, such as computer keyboards.
Add brushes, crevice tools, blower nozzles, extension wands, and other attachments to your vacuum hose.
These brushes, crevice tools, blower nozzles, extension wands, and other fittings work with any vacuum hose with the same diameter and manufacturer.
Attach these nozzles to your high-pressure water line to flush grit and grime out of blocked pipes.
Add a straw to an aerosol can for precise applications or replace a lost or clogged straw.
Keep torch tips clear for a pinpoint flame.
Scrape away solder buildup to keep desoldering nozzles clean.
Use one of these attachments with a vacuum to suck up concrete dust during drilling to help meet OSHA standards for silica dust exposure.