We will reply to your message within an hour.
More
In addition to a low-friction surface that prevents sticking and binding, this tough material is impact and wear resistant to handle the scuffs, scrapes, and strikes that other plastics can’t.
More sustainable than standard UHMW, these sheets and bars are made from partially recycled material, so they have a lower carbon footprint.
This material suppresses static charges to prevent dust from building up.
Made with carbon black, these recycled UHMW sheets are a sustainable alternative to standard UHMW sheets in applications where static electricity is a concern, such as in conveying equipment and chute liners.
The addition of carbon gives this material the ability to divert static electricity faster than antistatic UHMW.
Compared to our standard UHMW polyethylene, these sheets and bars hold up better to scuffs and scrapes in high-speed, high-precision, and high-impact applications—such as conveyor equipment, chute liners, and machine guards. Also known as Tivar HPV.
Often used in high-speed, high-precision, and high-impact applications, such as conveyor rollers and bearings, these rods stand up to scratches and scuffs better than our standard UHMW polyethylene rods. Also known as Tivar HPV.
Also known as Tivar H.O.T., this material lasts up to 10 times longer in high-temperature applications than standard UHMW.
The addition of glass fibers makes this material more abrasion resistant than standard UHMW. It’s also known as Tivar 88.
If a chip of this material breaks off, it can be located by metal detectors to reduce contamination risks.
This cast nylon 6 material is easier to machine than other types of nylon. It’s comparable to Nylatron and Nycast.
The addition of MDS results in a nylon with exceptional wear resistance as well as self-lubricating properties.
Often used to make gears and wear strips, these cast nylon 6 sheets and bars withstand higher temperatures and are easier to machine than standard nylon 6/6 sheets and bars.
Use these cast nylon 6 rods to make sheaves, bushings, and pulleys. All withstand higher temperatures and are easier to machine than standard nylon 6/6 rods.
A good choice for making sprockets and pulleys, these cast nylon 6 tubes withstand higher temperatures and are easier to machine than standard nylon 6/6 tubes.
This nylon stays lubricated over time because it’s filled with oil. Use it to fabricate parts for hard-to-reach places where adding lubricants would be difficult.
Practically nonabsorbent, HDPE won't swell when exposed to moisture. It is denser and more rigid than LDPE, plus it's more chemical resistant.
Also known as pipe-grade HDPE, these sheets are about four times more impact resistant than standard HDPE and hold up outdoors, and in wet environments.
Because PVC resists many acids and alkalies, it’s widely used for tanks and in chemical-processing applications. Also known as PVC Type 1.
Made of PVC Type 2 plastic, these 90° angles resist impact and chemicals.
Offering greater impact resistance than standard PVC Type 1 with similar chemical resistance, this PVC Type 2 is widely used for parts that are subject to shock.
CPVC is just as chemical resistant as standard PVC Type 1 and can handle hotter temperatures up to 200° F.
Create signs and partitions with this easy to cut PVC foam.
One of the softest and most flexible plastics we offer, LDPE is more formable than HDPE.
Often used for packaging and construction applications, this film is also known as Visqueen.
A polyester string reinforcement gives this material better tear resistance than standard LDPE film.
Polyester resists swelling in wet environments.
This film is often used as a separator when heating parts in an oven.
These black polyester rods protect from UV rays better than off-white polyester. Strong and semi-rigid, they won't swell in moist environments, so they're often made into valves, pump components, and spacers.
These black polyester sheets protect from UV rays better than off-white polyester. Strong and semi-rigid, they won't swell in moist environments, so they're often made into pump components and spacers.
When moisture-resistant polyester is combined with PTFE, the result is this self-lubricating material. It’s also called Hydex and PBT.
Known for its electrical insulating properties, this polystyrene is often used for cable connectors, electrical housings, and in microwave applications. It is also known as Rexolite.
Use Noryl PPO for electrical insulating applications where moisture is a concern. It remains dimensionally stable over time, even when temperatures fluctuate.
A satin texture on one side of these PETG sheets makes them semiclear. You can see light from the other side, but not detailed shapes. They are more resistant to scratching and glare than standard PETG.
Made with Teflon® PTFE resins, these sheets and bars surpass most plastics when it comes to chemical resistance and performance in extreme temperatures.
Known for its naturally slippery surface, PTFE surpasses most plastics when it comes to chemical resistance and performance in extreme temperatures.
This film is made with virgin Teflon® PTFE resins. It can handle extreme temperatures and resists most solvents.
Often used in assemblies that rub against each other, this powder blends into plastic, rubber, composites, and lubricants to keep them from sticking.
This glass-filled PTFE is more rigid than standard PTFE for increased durability in high-stress applications.
Also called reprocessed and mechanical-grade PTFE, this material is an economical alternative to standard PTFE.
Manufactured from Rulon PTFE, a PTFE that's modified with filler material for a super-slippery, impact-resistant surface that resists wear.
Protect sensitive equipment from damaging electrical static charges.
Not only does PEEK provide superior wear resistance in repetitive processes, it is also resists wear caused by abrasion. PEEK can be used as a lightweight substitute for metal parts in chemical-processing applications.
A glass filler is added to this this PEEK material to offer increased durability over standard PEEK in high-stress structural applications.
Common in food and pharmaceutical plants, these PEEK bars help you identify contaminated batches.
Often used in food and pharmaceutical plants, these PEEK rods help you prevent contaminated products from leaving your facility.
These PEEK sheets can be machined to tight tolerances for use in electrical and semiconductor parts, such as test sockets.
This film conducts electricity to prevent the buildup of static charges.
Kapton® polyimide film is an excellent electrical insulator.
Because this film dissipates heat, it is often used for printed circuit boards and power supplies.
Just as chemical resistant as PTFE, yet FEP offers greater impact strength. Use it to make valve components and gaskets.
Stronger than PTFE, PVDF offers good chemical resistance. Comparable to Kynar and Solef, it’s widely used for pump parts, tank liners, and seals.
When excellent chemical resistance is combined with an ability to hold tight tolerances, the result is PPS—a material that’s widely machined into parts for chemical-processing applications. It is comparable to Techtron and Ryton.
Offering excellent resistance to shock, PPSU is frequently fabricated into vehicle parts and machine components that are subject to vibration. It withstands higher temperatures than polysulfone and can handle repeated autoclaving cycles.
Often used as gaskets and bearings, this slippery-surface material absorbs virtually no moisture. PCTFE is equivalent to Kel-F and Neoflon.
Use PFA in place of PTFE and FEP for durability in repetitive processes, such as pump parts. It is chemical resistant across a wide temperature range.
A static-dissipative coating on this cast acrylic prevents electrostatic discharge from damaging sensitive electronic equipment.
Modified for increased impact strength over other types of acrylic, this acrylic is often used for skylights and outdoor signs.
This polycarbonate has a static-dissipative coating that prevents electrostatic discharge from damaging sensitive electronic equipment.
Because PVC resists acids and alkalies, it is often used in tanks and chemical-processing applications where visibility is essential.
Carbon mesh is embedded into this clear PVC film to dissipate electrostatic discharge and protect sensitive electronic equipment.
Static cling allows this PVC film to stick without an adhesive.
PETG can be formed into complex shapes without sacrificing durability.
The slippery surface on this FEP film prevents sticking. Use it as a release film when making molded parts.
PFA film retains its performance properties through a wide range of temperatures. It is often used to insulate cables.
Stronger and more chemical resistant than FEP and PFA film, ETFE film resists cracking over time.
This FRP fiberglass is made with a chemical-resistant resin that stands up to harsh environments.
Originally designed for the automotive and aerospace industries, these PAEK and carbon fiber sheets are a substitute for metal because they’re as light as aluminum and as strong as a nickel alloy.
Fabricate custom bottles, packaging, and other parts for chemical processing.
Print tough, long-lasting parts that won’t scratch or wear out from constant motion and friction, such as gears and washers.
Parts printed with these polyester filaments absorb less moisture than other types of plastic, making them ideal for use in wet or humid environments.
Print these polypropylene filaments into filters, gaskets, and other lightweight, foam-like parts that let air and gas pass through but repel water.
With a low coefficient of friction, these pellets won't wear away from abrasion that’s often caused by contact with moving parts. Melt and mold them into desired shapes.
Absorbing impact without cracking or breaking, these plastic pellets are molded into parts that endure bumps, scrapes, and falls.