A rubber coating provides a comfortable grip.

Position the head anywhere along the handle.

The handle is covered in rubber for a comfortable grip.

A gasket seals in permanent lubrication and keeps out dirt, dust, and moisture.

Also known as a construction or spud handle, wrenches use the pointed end to align bolt holes.

Insulated to protect against accidental contact with live electrical circuits, these wrenches are tested to 1,000 volts to meet IEC 60900.

No need to pull the socket off the tool—push a button to release.

Pivot the head to access fasteners in tight spots.

Unlike most torque wrenches, you don’t have to return the torque setting to the lowest value after use. These tools are also known as split-beam torque wrenches.

Made of beryllium copper, these wrenches satisfy OSHA requirements that specify nonsparking tools for locations where flammable vapors and combustible residues are present.

Measure with an accuracy of ±2%.

The most advanced torque wrenches we offer, these tools store and recall up to 1,500 torque and angle measurements.

A main pointer on the dial shows torque as it’s being applied and a memory pointer indicates the maximum torque reached.

These wrenches slip to disengage and stop turning the fastener when the set torque is reached, preventing overtightening.

Use these wrenches for medium-volume production, general maintenance, and construction applications.

Use these tools for general shop applications.

Made of aluminum-bronze, these sockets satisfy OSHA requirements that specify nonsparking tools for locations where flammable vapors and combustible residues are present.

With a plastic insert, these sockets firmly grip hex nuts and bolts without rounding them or scratching highly polished finishes.

Extra length allows access to fasteners on long bolts.

Quickly position these sockets on square and external 8-point fasteners.

Pivot the head to access fasteners from an angle.

These sockets fit the nuts found on water and gas valves.

Make maximum contact with all sides of a fastener to reduce slipping. These sockets are also known as torque adapters.

The opening shape makes more contact with fasteners for a better grip than standard open-end sockets. Also known as flare-nut or line wrench sockets, they're often used with flared tube fittings and fuel and hydraulic lines.

Insulated to protect against accidental contact with live electrical circuits, these sockets are tested to 1,000 volts to meet ASTM F1505 and IEC 60900.

The short bit on these sockets fits in spaces where height clearance is limited.

These sockets are also known as pin-in-Torx bits.

A magnet holds the fastener securely enough to drive self-tapping screws.

Pivot the head to access fasteners from an angle.

Tighten or loosen nuts and bolts without damaging the finish.

Extra length allows access to fasteners on long bolts.

Made of aluminum-bronze, these sockets satisfy OSHA requirements that specify nonsparking tools for locations where flammable vapors and combustible residues are present.

The hex shape grips hex fasteners and prevents rounding.

Push the square drive through the adapter to change size.

Extend your socket's reach.

Insulated to protect against accidental contact with live electrical circuits, these extensions are tested to 1,000 volts to meet IEC 60900.

Lock your socket into the extension to prevent accidental disengagement.

Pivot the head to access fasteners from an angle.

Adapters are set to a specific torque and cannot be adjusted.

Lock the adapter on your tool and the socket to the adapter to prevent accidental disengagement.

A magnet holds the socket, making changes quicker.

Lock your socket into the extension to prevent accidental disengagement.

Prevent overtightening that can damage fasteners. These adapters spring back slightly when the set torque is reached.

Bend these extensions around obstructions to access hard-to-reach fasteners.

A ratchet mechanism allows you to turn fasteners without removing and repositioning the socket.

The opening shape makes more contact with fasteners for a better grip than standard open-end sockets. Also known as flare-nut or line wrench sockets, they're often used with flared tube fittings and fuel and hydraulic lines.

The short bit on these sockets fits in spaces where height clearance is limited.

These sockets are also known as pin-in-Torx bits.

Made in the U.S.A., these tools handle the toughest industrial applications, provide the best grip on fasteners, and have a superior finish.

For high quality at a lower price, choose these U.S.A.-made sets.

Made in the U.S.A., these tools handle the toughest industrial applications, provide the best grip on fasteners, and have a superior finish.

Made of aluminum-bronze, these sockets satisfy OSHA requirements that specify nonsparking tools for locations where flammable vapors and combustible residues are present.

Quickly position these sockets on square fasteners.

Attach to your socket for a longer reach.

Use these sockets as an alternative to a screwdriver or L-key. They are made to withstand the high torque and force of impact tools.

Lock your socket into the extension to prevent accidental disengagement.

The hex shape grips hex fasteners and prevents rounding. These sockets are made to withstand the high torque and force of impact tools.

Pair these tools with your ratchet wrench to get more leverage.