These wrenches are made of stainless steel for excellent corrosion resistance.

When working in tight spaces, these short wrenches fit where others can't.

Flip these wrenches over to ratchet in the opposite direction.

A lever reverses the ratchet direction.

A spline-shaped box end turns spline, hex, and 12-point fasteners. This shape also gets a better grip on rounded fasteners that can be difficult to turn with a traditional wrench.

Suitable for occasional maintenance work, these sets are imported.

These wrenches are made of stainless steel for excellent corrosion resistance.

When working in tight spaces, these short wrenches fit where others can't.

Suitable for occasional maintenance work, these sets are imported.

Pivot the box end for access to fasteners in tight spots.

Made in the U.S.A., these tools handle the toughest industrial applications, provide the best grip on fasteners, and have a superior finish.

A spline-shaped box end turns spline, hex, and 12-point fasteners. This shape also gets a better grip on rounded fasteners that can be difficult to turn with a traditional wrench.

These wrenches are made of stainless steel for excellent corrosion resistance.

The slim head fits into tight spaces and around thin fasteners.

The opening shape makes more contact with fasteners for a better grip than standard open-end wrenches. These tools are also known as flare-nut or line wrenches.

The head is offset 45° to provide additional clearance when reaching over obstructions.

One head is angled 60° for access to hard-to-reach fasteners. These are also known as ignition wrenches.

The slim heads fit into tight spaces and around thin fasteners.

The opening shape makes more contact with fasteners for a better grip than standard open-end wrenches. These tools are also known as flare-nut or line wrenches.

The shaft on these wrenches extends and locks.

Made of aluminum-bronze, these wrenches satisfy OSHA requirements that specify nonsparking tools for locations where flammable vapors and combustible residues are present.

Position the head anywhere along the handle.

Set the desired torque and the wrench indicates when it's reached with an audible click and an impulse in the grip.

Trust the precision of your measurements—these wrenches are accurate to ±1%.

A main pointer on the dial shows torque as it’s being applied and a memory pointer indicates the maximum torque reached.

Built for durability, these high-performance tools handle the demands of high-volume production and tough maintenance applications.

Made of aluminum-bronze, these sockets satisfy OSHA requirements that specify nonsparking tools for locations where flammable vapors and combustible residues are present.

These short sockets fit spaces where height clearance is limited.

Pivot the head to access fasteners from an angle.

Quickly position these sockets on square and external 8-point fasteners.

The opening shape makes more contact with fasteners for a better grip than standard open-end sockets. Also known as flare-nut or line wrench sockets, they're often used with flared tube fittings and fuel and hydraulic lines.

A ratchet mechanism allows you to turn fasteners without removing and repositioning the socket.

Insulated to protect against accidental contact with live electrical circuits, these sockets are tested to 1,000 volts to meet ASTM F1505 and IEC 60900.

Pivot the head to access fasteners from an angle.

With a smaller OD than standard sockets, these fit between tightly spaced fasteners.

Made of aluminum-bronze, these sockets satisfy OSHA requirements that specify nonsparking tools for locations where flammable vapors and combustible residues are present.

Extra length allows access to fasteners on long bolts.

Made of aluminum-bronze, these sockets satisfy OSHA requirements that specify nonsparking tools for locations where flammable vapors and combustible residues are present.

Made in the U.S.A., these tools handle the toughest industrial applications, provide the best grip on fasteners, and have a superior finish.

Pivot the head to access fasteners from an angle.

Quickly position these sockets on square fasteners.

Make maximum contact on all sides of a fastener to reduce slipping. These sockets are also known as torque adapters.

Often used with an extension, these sockets turn fasteners and fittings in obstructed areas that a regular socket can't reach. They are also known as crowfoot wrenches.

Turn nuts on bolts and threaded rod, which pass through these sockets.

Pivot the head to access fasteners from an angle.

Convert from one square drive size to another.

Convert from one square drive size to another.

Change a standard wrench handle into a ratcheting wrench.

A magnet holds the socket, making changes quicker.

Pivot the head to access fasteners from an angle.

The heads are angled to provide clearance around obstructions.

Ratchet mechanisms allow you to turn fasteners in tight spaces without removing and repositioning the tool.

An insulated handle protects against accidental contact with live electrical circuits. These wrenches are tested to 1,000 volts to meet IEC 60900.

The offset head gives you additional clearance to turn hard-to-reach fasteners.

Open the jaws to fit around a fastener like an open-end wrench; close the jaws and the wrench acts like a ratcheting box wrench.

The heads are offset to provide clearance for reaching over obstructions.

The heads are offset 45° to provide clearance for reaching over obstructions.

Turn lug bolts on car and truck wheels. These wrenches have a different socket size at each end.

Turn nuts on bolts and threaded rod, which can pass through the short end of the wrench. For additional leverage, slip a bar through the short end to create a T-handle.

These wrenches have one pivoting socket end and one open end.

Sets include an assortment of keys. These simple tools turn fasteners from either end and reach into tight spots.

Made of beryllium copper that is FM approved, these keys help meet OSHA requirements that specify nonsparking tools for locations where flammable vapors and combustible residues are present. They turn fasteners from either end and reach into tight spots.