The handle is covered in rubber for a comfortable grip.

Twist the grip to rapidly turn a socket before final tightening or to remove a fastener once loosened. The handle also swings like a traditional ratchet wrench.

A gasket seals in permanent lubrication and keeps out dirt, dust, and moisture.

Pivot the head to access fasteners in tight spots.

The 25° offset head provides clearance when reaching over obstructions.

Bolts and threaded rod pass through these wrenches when used with bolt-through sockets.

A rubber coating provides a comfortable grip.

Position the head anywhere along the handle.

Fasten quickly with these crank-style handles.

Pivot the head to access fasteners in tight spots.

Unlike most torque wrenches, you don’t have to return the torque setting to the lowest value after use. These tools are also known as split-beam torque wrenches.

Turn sockets from above when there's not room to swing a standard wrench handle.

When the set torque is reached, these wrenches signal with an audible click and an impulse in the grip.

Trust the precision of your measurements—these wrenches are accurate to ±2%.

Trust the precision of your measurements—these wrenches are accurate to ±1%.

The most advanced torque wrenches we offer, these tools store and recall up to 1,500 torque and angle measurements.

Built for durability, these wrenches handle the demands of high-volume production and tough maintenance applications.

Use these wrenches for medium-volume production, general maintenance, and construction applications.

Made in the U.S.A., these tools handle the toughest industrial applications, provide the best grip on fasteners, and have a superior finish.

Suitable for occasional maintenance work, these sets are imported.

Made in the U.S.A., these tools handle the toughest industrial applications, provide the best grip on fasteners, and have a superior finish.

With sizes from EP10 to EP24, these sets have the sockets you need to install and remove a wide range of External Torx-Plus fasteners. Pair them with a square drive tool, such as a socket wrench, to deliver high levels of torque without slipping.

The ball end allows angled entry when you don't have exact alignment between the socket bit and fastener.

Extra-long bits allow access to hard-to-reach fasteners.

Keep a convenient mix of hex, Torx, Phillips, and slotted bit sockets on hand.

Lock your socket into the extension to prevent accidental disengagement..

A ratchet mechanism allows you to turn fasteners without removing and repositioning the socket.

The opening shape makes more contact with fasteners for a better grip than standard open-end sockets. Also known as flare-nut or line wrench sockets, they're often used with flared tube fittings and fuel and hydraulic lines.

Lock your socket into the extension to prevent accidental disengagement.

Pivot the head to access fasteners from an angle.

These sockets are made to withstand the high torque and force of impact tools.

Extra-long bits allow access to hard-to-reach fasteners.

These sockets are also known as pin-in-Torx bits.

Extra-long bits allow access to hard-to-reach fasteners.

These sockets fit the nuts found on water and gas valves.

Pivot the head to access fasteners from an angle.

Pivot the head to access fasteners from an angle.

Insulated to protect against accidental contact with live electrical circuits, these sockets are tested to 1,000 volts to meet IEC 60900.

Turn many sizes of square, hex, and 8-point fasteners with one socket. Place over the fastener and 54 pins move to grip it securely.

A ratchet mechanism allows you to turn fasteners without removing and repositioning the socket.

The opening shape makes more contact with fasteners for a better grip than standard open-end sockets. Also known as flare-nut or line wrench sockets, they're often used with flared tube fittings and fuel and hydraulic lines.

A rubber insert grips the plug to prevent damage.

A magnet holds the fastener securely enough to drive self-tapping screws.

With a smaller OD than standard sockets, these fit between tightly spaced fasteners.

Pivot the head to access fasteners from an angle.

The hex shape grips hex fasteners and prevents rounding.

Insulated to protect against accidental contact with live electrical circuits, these extensions are tested to 1,000 volts to meet IEC 60900.

Lock your socket into the extension to prevent accidental disengagement.

Pivot the head to access fasteners from an angle.

Change a standard wrench handle into a ratcheting wrench.

A digital display shows how torque measurements change as you turn the wrench. Set the desired torque and angle—lights and an audible alarm indicate when target has been reached or exceeded.

Lock the adapter on your tool and the socket to the adapter to prevent accidental disengagement.

Convert from one square drive size to another.

Bend these extensions around obstructions to access hard-to-reach fasteners.

Attach to your socket for a longer reach.

Pivot the head to access fasteners from an angle.