Convert from one square drive size to another.

These adapters are insulated to protect against accidental contact with live electrical circuits. They are tested to 1,000 volts to meet IEC 60900.

Insulated to protect against accidental contact with live electrical circuits, these extensions are tested to 1,000 volts to meet IEC 60900.

The square drive has a rounded shape that allows the extension to pivot inside the socket opening and turn it from an angle.

Fit these adapters between your wrench and socket to enable finger tightening.

Set a desired torque within the range.

Pivot the head to access fasteners from an angle.

Use sockets with tools that accept hex shanks, such as impact drivers and power drills.

Convert from one square drive size to another.

Lock your socket into the extension to prevent accidental disengagement.

Extra-long bits allow access to hard-to-reach fasteners.

The ball end allows angled entry when you don't have exact alignment between the socket bit and fastener.

These sockets are also known as pin-in-hex or pin-in-socket bits.

Also known as pipe plug sockets, these sockets have a square shape that provides the best possible grip on square fasteners and prevents rounding.

These short sockets fit spaces where height clearance is limited.

Quickly position these sockets on square fasteners.

Insulated to protect against accidental contact with live electrical circuits, these sockets are tested to 1,000 volts to meet IEC 60900.

Turn many sizes of square, hex, and 8-point fasteners with one socket. Place over the fastener and 54 pins move to grip it securely.

Grip the indentations around the outside of tri-groove fasteners.

Often used with an extension, these sockets turn fasteners and fittings in obstructed areas that a regular socket can't reach. They are also known as crowfoot wrenches.

A ratchet mechanism allows you to turn fasteners without removing and repositioning the socket.

Pivot the head to access fasteners from an angle.

Achieve the best possible grip on hex fasteners and prevent rounding.

With a smaller OD than standard sockets, these fit between tightly spaced fasteners.

Extra length allows access to fasteners on long bolts.

The 12-point shape quickly positions on hex fasteners.

The hex shape grips hex fasteners and prevents rounding.

Pivot the head for access to fasteners in tight spots.

Position the head anywhere along the handle.

The handle is covered in rubber for a comfortable grip.

The shaft on these wrenches extends and locks.

A gasket seals in permanent lubrication and keeps out dirt, dust, and moisture.

Rather than teeth, these wrenches use a series of rollers to engage the ratchet, enabling work in the tightest of spaces. Also known as silent ratchets, they don't make the traditional click sound when turned.

No need to pull the socket off the tool—push a button to release.

Pivot the head to access fasteners in tight spots.

Turn sockets from above when there's not room to swing a standard wrench handle.

Set the desired torque and the wrench indicates when it's reached with an audible click and an impulse in the grip.

Unlike most torque wrenches, you don’t have to return the torque setting to the lowest value after use. These tools are also known as split-beam torque wrenches.

Insulated to protect against accidental contact with live electrical circuits, these wrenches are tested to 1,000 volts to meet IEC 60900.

Turn sockets from above when there's not room to swing a standard wrench handle.

Measure with an accuracy of ±2%.

A main pointer on the dial shows torque as it’s being applied and a memory pointer indicates the maximum torque reached.

Measure with an accuracy of ±7%.

Use these wrenches for medium-volume production, general maintenance, and construction applications.

Set torque and the wrench will prevent you from exceeding it. These are also known as nutrunners.

The short bit on these sockets fits in spaces where height clearance is limited.

Extra-long bits allow access to hard-to-reach fasteners.

Keep a convenient mix of hex, Torx, Phillips, and slotted bit sockets on hand.

Made in the U.S.A., these tools handle the toughest industrial applications, provide the best grip on fasteners, and have a superior finish.

Suitable for occasional maintenance work, these sets are imported.

Suitable for occasional maintenance work, these sets are imported.

For high quality at a lower price, choose these U.S.A.-made sets.

With sizes from EP10 to EP24, these sets have the sockets you need to install and remove a wide range of External Torx-Plus fasteners. Pair them with a square drive tool, such as a socket wrench, to deliver high levels of torque without slipping.

Lock your socket into the extension to prevent accidental disengagement..

Often used with an extension, these sockets turn fasteners and fittings in obstructed areas that a regular socket can't reach. They are also known as crowfoot wrenches.

The opening shape makes more contact with fasteners for a better grip than standard open-end sockets. Also known as flare-nut or line wrench sockets, they're often used with flared tube fittings and fuel and hydraulic lines.

Convert from one square drive size to another.

Attach to your socket for a longer reach.

Pivot the head to access fasteners from an angle.

Use your ratchet wrench as a handle to reach filters and other round objects in tight spots.