Rated for continuous use, these pumps are often used to move caustics such as antifreeze and salt water. Mount them in any position, even upside down. Also known as diaphragm pumps, they are typically used for low-flow spraying, draining, and washdown applications.

A high-horsepower motor moves oil with a viscosity similar to SAE 60 motor oil. Also known as gear pumps, these produce a smooth flow of liquid to lubricate equipment and blend oils.

An aluminum enclosure around the motor provides protection in dusty and dirty environments. Designed to fit into small equipment, these pumps have miniature gears and a subfractional horsepower motor for low-flow applications.

Commonly called rotary vane pumps, these are designed to pump water at high pressures in low-flow applications. Use at pressures up to 240 psi.

Keep your circulation pump in working order by replacing broken or worn parts.

A cast iron housing and steel gears allow these pumps to be used to dispense oil and fuel such as hydraulic oil and diesel fuel. Also known as gear pumps, they produce a smooth flow of liquid for applications such as engine lubrication.

Commonly called rotary vane pumps, they have a built-in bypass relief valve to prevent pressure buildup.

Replace worn or broken parts on your transfer pump.

The float switch is wired to the pump. Use with debris-free water.

The float switch has a separate cord that can unplug, so you can replace the switch without replacing the whole pump. Use with debris-free water.

Since the switch activates on increasing pressure caused by rising water levels, these pumps have no external moving parts to catch on sump pit walls. Use with debris-free water.

These pumps have an explosion-proof motor that is rated for use where hazardous material is present. Since the motor is totally enclosed fan cooled (TEFC) and never comes into contact with the water, the pump can be used with hot water up to 300° F.

The intake is 2" from the base of the pump to prevent dirt at the bottom of your sump pit from clogging the pump. Use with debris-free water.

An alarm and a red light alert you when water levels rise too high.

Place your pump inside these basins for ground-level applications and below-ground use without a sump pit.

These pumps provide over 50% more flow than standard plug-in activated pumps for sewage water. They activate when plugged in. You can add a plug-in switch to control when the pump activates. Pumps are equipped with a large intake and rugged impeller to transfer raw sewage water with solids up to 2” in diameter.

These pumps provide about 25% more flow than standard float-switch activated pumps for sewage water. The float switch has a separate cord that can unplug, so you can replace the switch without replacing the whole pump. Pumps are equipped with a large intake and rugged impeller to transfer raw sewage water with solids up to 2” in diameter.

The float switch has a separate cord that can unplug, so you can replace the switch without replacing the whole pump.

Equipped with a large intake and a rugged impeller, these pumps transfer raw sewage water with solids up to 2” in diameter. The float switch is wired to the pump.

These pumps have a heavy duty motor with sealed bearings that generates a flow rate similar to our other sump pumps for sewage water while using fewer amps. Use them to transfer raw sewage water with solids up to 2” in diameter. The float switch is wired to the pump.

Move higher volumes of water with solids than other sump pumps. The float switch has a separate cord that can unplug, so you can replace the switch without replacing the whole pump. Also known as effluent pumps, they accommodate solids up to 3/4” in diameter. They are often used with liquid waste that has passed through a septic tank, so most solids are removed.

These pumps activate when plugged in. You can add a plug-in switch to control when the pump activates. Also known as effluent pumps, these accommodate solids up to 3/4" in diameter. They're often used with liquid waste that has passed through a septic tank, so most solids are removed

The float switch has a separate cord that can unplug, so you can repair the switch without replacing the whole pump. Also known as effluent pumps, these accommodate solids up to 3/4" in diameter. They're often used with liquid waste that has passed through a septic tank, so most solids are removed.

If the primary float fails, the backup float kicks in and an alarm sounds to indicate float malfunction.

Hang these switches in a sump pit to detect rising water levels.

This pump has a totally enclosed nonventilated (TENV) motor that is cooled by the liquid being pumped. Also known as a flexible impeller pump, it creates a suction force that can draw liquid upward to fill the pump chamber when your liquid source is below the pump.

These pumps have an impact-resistant aluminum housing and handle larger solids than other battery-operated water-removal pumps. Use them to remove water from areas without power.

Also known as bilge pumps, these remove fresh and salt water from spots where other pumps don’t fit.

Move higher volumes of water than with other high-flow water-removal pumps. These pumps activate when plugged in. You can add a plug-in switch to control when the pump activates.

An aluminum housing provides excellent impact resistance. Use these pumps to clean up water in flooded areas without a sump pit. Pumps activate when plugged in. You can add a plug-in switch to control when the pump activates.

Fill the fuel tank with gasoline to remove water at sites without power.

Kits include 20 feet of PVC suction hose, 50 feet of PVC discharge hose, a suction strainer, and two steel thread adapters.

Wheel these pumps to remote areas with no power. They can handle sewage water with thick sludge, silt, and debris up to 2” in diameter.

The polypropylene housing provides good resistance to caustics such as ammonia, electropolishing solutions, and detergents and cleaning fluids.

A stainless steel construction allows these pumps to be used with aggressive chemicals such as methyl ethyl ketone and xylene.

These pumps are designed for use in food and beverage applications.

With wetted parts made of FDA listed materials, these pumps can be used with food, water, and beverage. They have a nonsparking motor for use in applications where electricity is unavailable or dangerous.

Often used with ammonia, etching and cleaning solutions, and other caustics, these pumps have a nonsparking air-powered motor for applications where electricity is unavailable or dangerous.

These pumps have a motor that is rated for IEC Zone 1, Groups IIB and IIA; and IEC Zone 21, Groups IIIC, IIIB, and IIIA hazardous locations with flammable gases and vapors, so they can be used with liquids such as acetone, ethanol, methyl ethyl ketone, xylene, and mineral spirits.

With a higher pressure than other air-powered drum pumps, these pumps move thick chemicals with a viscosity of up to 5,000 centipoise. A stainless steel housing stands up to acids, solvents, and other caustics.

These pumps have a selectable flow rate, so you can adjust flow for different dispensing applications. A lever handle maximizes output with each stroke for low-effort dispensing.

Rotate the handle to dispense a continuous flow of liquid.

Designed to move low volumes of caustic liquids in confined areas, these pumps have a thin intake tube and a small handle.

Eliminate leaks and waste with a faucet-style nondrip nozzle that quickly starts and stops flow.

Made with PTFE components, these pumps stand up to aggressive chemicals our other drum pumps can't, such as hydrochloric acid, bleach, sodium hydroxide, and methyl ethyl ketone.

Rotate the handle to dispense a continuous flow of liquid.

All of these pumps have bonding and grounding wires, while some also have an internal flame arrester, to pump fuel, cleaning solvents, and lacquer thinners.

These pumps have a discharge hose for transfer applications and a vacuum breaker that drains the hose to prevent siphoning. A lever handle delivers fluid on both the forward and backward strokes for faster dispensing than other drum pumps.

Eliminate leaks and waste with a faucet-style nondrip nozzle that quickly starts and stops flow.

For low‐effort dispensing, a lever handle maximizes output with each stroke. The handle delivers fluid on both the forward and backward strokes to quickly move drum contents.

Made with polypropylene components, these pumps withstand highly corrosive diesel exhaust fluid while preventing it from crystallizing.

Drain and transfer liquid more quickly and easily than hand-operated pumps and siphon pumps.

Designed to move 40 gallons of liquid per minute, these pumps quickly empty drum contents.

For accurate dispensing in extremely low-flow applications, these pumps allow you to adjust flow in 2% increments.

Commonly used in food, beverage, pharmaceutical, and cosmetic processing, these pumps are designed for sanitary environments.

Attach these pumps to any 12-volt battery for on-site diesel fuel dispensing at construction sites, on boats, and in other environments without electrical hookups.

Operating on a 12-volt battery, use these pumps to transfer and drain fuel such as gasoline, diesel fuel, and kerosene.

Quickly generate suction with battery power.

Made of PVDF components, these pumps resist harsh chemicals such as hydrochloric acid and sulfuric acid. They have a foot pedal for hands-free operation.

These pumps can be submerged or connected remotely to a pipe in your line. Use them to circulate water in small tanks, cooling baths, fountains, and other low-flow applications.

Magnets turn the impeller so there's no shaft seal to wear out. Submerge these pumps to circulate water in small tanks, cooling baths, fountains, and other low-flow applications.

Protected from impact by a durable epoxy-coated aluminum housing, these pumps can be submerged or connected remotely to a pipe in your line. Use to circulate water in small tanks, cooling baths, fountains, and other low-flow applications.

Also known as deep-well submersible pumps, use these pumps to transfer drinking water from wells and cisterns up to 250 ft. deep.

These pumps circulate solvent-based parts-washing solutions.

Also known as peristaltic pumps and tubing pumps, these maintain a fixed flow rate.

These pumps meter a consistent amount of liquid within ±2% of the maximum flow.

A 316 stainless steel housing provides corrosion resistance for a long life in harsh environments. These pumps meter a consistent amount of liquid within ±2% of the maximum flow.

With a footprint that's only a few inches in any direction, these pumps fit into compact systems to dispense small amounts of acids, cleaning fluids, and other chemicals. They're often used in sterilization, photochemical, and water treatment systems.

These pumps can be used with pressures four times higher than standard pumps for chemicals.

Rated for liquids with a viscosity up to 10,000 centipoise, these pumps can be used with very thick chemicals such as electropolishing solutions.

An adjustment screw lets you increase or decrease flow rate without the hassle of changing tubing. Often used in boiler feed systems and water treatment, these pumps are compatible with chemicals such as cleaning fluids and acid-washing solutions.

Generate a vacuum on demand with these pumps that come mounted on a 10-gal. ASME code vacuum tank for quick startup. They're often used in vacuum-forming applications, such as product packaging.

These pumps weigh only 16 pounds and have a handle, so they're convenient for on‐site sampling, atomizing, and vacuum filtration.

Achieve powerful vacuum and continuous flow for applications such as vacuum drying, solvent evaporation, and distillation.

Generate the suction you need to power end-of-arm tools, such as vacuum cups and grippers, without using an installed vacuum system. These pumps, also known as venturi devices, connect to any compressed air source and come with all the electrical connections you need to start lifting or moving objects.

Also known as venturi pumps, these compressed-air-powered pumps are commonly used in vacuum packaging, pick-and-place operations, and end-of-arm robotic tooling.

Equipped with a built-in container for condensate, these pumps work alongside your system to remove condensate from air conditioners, refrigerators, dehumidifiers, and other equipment. They are not submersible.

Use these pumps in low-pressure steam systems to capture hot condensate and return it to your boiler or feed unit.

To handle high condensate volume, the workload is distributed between two pumps for a longer service life than standard steam condensate pumps. Use in low-pressure steam systems to capture hot condensate and return it to your boiler or feed unit.

Move a higher volume of condensate than standard steam condensate pumps. Use these pumps in low-pressure steam systems to capture hot condensate and return it to your boiler or feed unit.