With strength for higher load capacities than other ball-grip positioning arms, these arms have a heavy duty construction.

Heavy duty construction adds strength for higher load capacities than other positioning arms.

Bend these arms to hold small equipment such as lights and microphones in almost any position.

Stronger and with greater load capacities than gooseneck-style positioning arms, these arms keep their shape even when moving or when exposed to vibration. They’re often used in robotics and conveyor applications when frequent repositioning isn’t required.

A suction base makes it easy to move and attach these arms to smooth surfaces such as glass and polished metal.

Adjust the flexible arm to nearly any position.

The base is comprised of adjustable magnetic pins which allow it to conform to any shape and grip most metal surfaces.

For more versatility than other low-profile holders, this holder has six locations for mounting indicators and accessories, including two mounting holes and four places to mount an indicator lug back with the included thumb screws.

Use this holder in areas with limited space. It has a nut and bolt for holding a 1/4” lug-back indicator.

Adjust the flexible arm to nearly any position.

Adjust the flexible arm to nearly any position.

Attach the C-clamp on these holders to your milling machine head to take indicator measurements without obstructing the cutting tool.

These Mitutoyo indicators have a magnetic base with V-grooved bottom to provide a solid mount on flat and curved metal surfaces. They also have a magnetic release switch for easy setups.

For a solid mount on metal surfaces, these indicators come with a magnetic base. They have a continuous dial numbered clockwise around the face for direct measurements. A spring-loaded plunger retracts and extends to measure objects.

A magnetic base provides a solid mount on metal surfaces.

Suspend tools to keep them out of the way but still within reach.

The head rotates 360° and tilts up and down.

Bend and wrap the legs around almost anything while keeping a level mounting surface.

Attached to an arm you can flex into position, these clamps hold objects such as a flashlight, tool, or instructions.

Mount these clamps to a bench top or other surface to keep workpieces in place.

Hold workpieces of slightly different thicknesses with one clamp. These clamps automatically adjust to compensate for imperfections or small inconsistencies on the material’s surface.

Push the lever to lock the handle and prevent accidental opening.

Hold workpieces of different thicknesses without adjustment.

A highly durable construction with hardened steel pivot pins and bushings provides a long service life.

Push the lever to lock the handle and prevent accidental opening.

Weld these clamps to the side of an object or drill your own holes in the mounting plate and bolt into place.

Two sets of mounting holes allow mounting on the bottom or side.

The handle locks in a horizontal position for more clearance above the clamp.

Replace worn screws or customize your clamps.

Suitable for production applications, these clamps have double the service life of other air-powered toggle clamps.

The base fits into round or square holes on most workholding tables for clamping anywhere on the work surface.

Push or pull the plunger to hold your workpiece from the side.

Moving parts are sealed to prevent dirt and dust from clogging the clamp.

A highly durable construction with hardened steel pivot pins and bushings provides a long service life.

Secure your workpiece from the side by fully extending the plunger, and push a lever to lock the handle in place.

The handle can be rotated 125° for easier access or extra clearance above the clamp.

Push the lever to lock the handle and prevent accidental opening.

The plunger can be locked at any position along its travel.

Fit the draw arm over a latch plate and pull the handle to clamp.

Push the lever to lock the handle and prevent accidental opening.

When loosened, you can spin the body of this clamp around its mounting point for better access to the workpiece.

The clamping arm slides freely along the bar for quick, one handed positioning. Tighten the screw onto a workpiece and the arm locks in place.

For the most demanding jobs, these clamps have almost five times the capacity of standard fast-action bar clamps.

Hold up to five times the capacity of standard bar clamps. These are also known as I-beam clamps.

Pull the lever to slide the clamping arm along the bar; release to lock in place.

All adjustments can be made from one end, allowing clamping in tight spaces.

Each arm slides freely for quick, one-handed positioning. They lock when the screws are tightened onto a workpiece.

Press the trigger to slide the clamping arm along the bar. Release the trigger and squeeze the pistol-grip handle to lock the clamp in place.

Clamp much farther in from the edge of the workpiece than with standard bar clamps.

Mount using the holes in the base.

Secure small parts in spring clamps to keep hands free for soldering, gluing, and assembly.

Manually control these standard free-moving lid supports through their full range of motion. Raise or lower the lid until the hold-open mechanism on the support is engaged; slightly lift it again to release the hold and close the lid.

Also known as hatch springs, these supports are commonly used on hatches and other top-opening lids. Raise the lid to extend the spring, which props the lid open—an internal cable keeps the spring from overextending. Press the center of the spring to release the hold and close the lid.

Commonly used on hood and trunk lids, these simple, three-piece rods telescope from 18 1/2" to 46 3/4" to prop lids open at a variety of angles.

Providing constant resistance through the full range of motion, these supports hold lids open at any angle up to 70° or 90°.

Springs provide lifting assistance to raise and hold lids open—slightly lift the lid to get it started and the support will do the rest. Manually shut the lids and the supports will hold them in the closed position.

For frequently used doors, these closers last twice as long as standard door closers. They can replace Yale, Dorma, Falcon, Stanley, Parker, and Cal-Royal models with the same mounting hole pattern.

To protect doors and walls, these closers have a shock-absorbing stop to damp the force of doors when they’re pushed open. Designed for frequently used doors, these last twice as long as standard door closers. They can replace Yale, Dorma, Falcon, Stanley, Parker, and Cal-Royal models with the same mounting hole pattern.

Save time and money by replacing worn or damaged arms instead of the entire closer.

No need to drill new holes—these closers have a mounting plate that fits the hole patterns of most closers from Norton, LCN, Yale, Corbin Russwin, and Dorma.

Nudge your door and these openers will open it the rest of the way.

Simple and compact, these closers have an arm that rolls along gates to push them closed.

Springs retract to pull storm doors and gates closed.

Use these closers when your door-to-door clearance is limited. They close storm doors more smoothly than standard spring closers.

These openers are often used on older casement and awning windows.

Add or replace parts such as die sets, power drives, and die head adapters on Ridgid Pipe and Conduit Threaders.

Also known as clamping handles, use these standard adjustable handles for applications involving frequent positioning, tightening, and holding adjustments. Lift the handle to rotate freely; then release the handle to engage and tighten.

Identify equipment controls and components at a glance by their color. Also known as clamping handles, use these handles for applications involving frequent positioning, tightening, and holding adjustments. Lift the handle to rotate freely; then release the handle to engage and tighten.

For fast clamping anywhere along a threaded rod, press the button to slide the handle into position; release the button to secure. These handles are also known as clamping handles.

A soft textured surface provides a comfortable grip for applications involving frequent positioning, tightening, and holding adjustments. Lift the handle to rotate freely; then release the handle to engage and tighten. These handles are also known as clamping handles.

Attach a ball knob to one of these shafts to create custom handles for operating machinery.

Also known as finger handles, these are less than 1" long. Use them as tiny grips on small hand wheels and cranks to operate machinery.

These handles are often used for operating machinery.

Press fit one of these handles into a shaft, rod, or hand wheel to operate machinery.

Ratcheting action allows for quick adjustment to machinery and valves in tight spaces. All of these handles have a straight, open socket head for long shafts to pass through.

Add a pin, rod-end bolt, or other mounting hardware to build a custom assembly. Also known as double cams, these handles have a durable, extra-large handle for clamping on fixture bases, plates, and workpieces. For fast adjustments, push down on the handle and the head applies pressure to quickly draw two parts together.

Round long shafts can pass through these handles for mounting versatility. Create custom threads or drill a hole in the side of the hub to secure with a set screw. Often used on cross-slide tables, these crank handles provide leverage to maximize force for turning and tightening.

Square long shafts can pass through these handles for mounting versatility. Drill a hole in the side of the hub to secure with a set screw. These crank handles provide leverage to maximize force for turning and tightening. They are often used on cross-slide tables.

Use these crank handles for applications that involve frequent machinery adjustments. They provide leverage to maximize force for turning and tightening.