System of Measurement System of Measurement |
---|
|
End Type End Type |
---|
![]() | ![]() |
Threaded | With Retaining Ring Grooves |
![]() | ![]() |
Tapped | D-Profile |
Material Material |
---|
|
Thread Size Thread Size | Show |
---|
Thread Size Thread Size | Hide |
---|
Finish Finish |
---|
|
For Motion Type For Motion Type |
---|
![]() | Rotary |
Hardness Rating Hardness Rating |
---|
|
Yield Strength Yield Strength |
---|
|
Hole Diameter Hole Diameter |
---|
|
End-to-Groove Length End-to-Groove Length |
---|
|
Groove Width Groove Width |
---|
|
Number of Grooves Number of Grooves |
---|
|
Retaining Ring Included Retaining Ring Included |
---|
|
Mechanical Finish Mechanical Finish |
---|
|
Bolt Circle Diameter Bolt Circle Diameter |
---|
|
More
More
More
Mount the flange to a machine or wall to support idler sprockets and pulleys in tensioning applications. They include washers and a nut to position your component and hold it in place.
For technical drawings and 3-D models, click on a part number.
Overall | Thread | Mounting Holes | |||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
Dia. | Lg. | Lg. | Dia. | Size | Lg. | Flange Thick. | Bolt Circle Dia. | No. of | Dia. | Edge Type | Hardness Rating | Hardness | Yield Strength, psi | Each | |
Inch—Zinc-Plated 1215 Carbon Steel | |||||||||||||||
3/8" | 7/16" | 1 3/16" | 1 1/4" | 5/16"-18 | 15/32" | 9/32" | 29/32" | 4 | 5/32" | Straight | Not Rated | Not Rated | Not Rated | 0000000 | 000000 |
Thread these shafts into a tapped hole to support idler sprockets and pulleys in tensioning applications. They have a retaining-ring groove, retaining ring, and spacers to position your component and hold it in place.
For technical drawings and 3-D models, click on a part number.
Overall | Thread | Groove | ||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
Dia. | Lg. | Lg. | Dia. | Size | Lg. | Wd. | Dia. | End-to-Groove Lg. | Edge Type | Hardness Rating | Hardness | Yield Strength, psi | Each | |
Inch—Zinc-Plated 1215 Carbon Steel | ||||||||||||||
1/2" | 5/8" | 1 9/16" | 1" | 5/16"-18 | 1/2" | 0.046" | 0.396" | 0.125" | Chamfered | Not Rated | Not Rated | 65,000 | 000000 | 00000 |
5/8" | 5/8" | 1 19/32" | 1 1/8" | 5/16"-18 | 17/32" | 0.046" | 0.485" | 0.125" | Chamfered | Not Rated | Not Rated | 65,000 | 000000 | 00000 |
Connect these internally threaded shafts directly to threaded components, or use a fastener to secure. They have a flat surface area that allows set screws to dig into the shaft for securely mounting gears, sprockets, and bearings. Shafts are 1045 carbon steel, a general purpose shafting material that balances high strength and good machinability. The edges are chamfered to remove sharp corners, reducing damage to bearings, housings, and other components during installation. All are turned, ground, and polished to meet tight diameter and straightness tolerances.
For technical drawings and 3-D models, click on a part number.
Thread | ||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|
Lg. | Flat Wd. | D-Profile Lg. | Size | Lg. | Lg. Tolerance | Straightness Tolerance | Edge Type | Hardness Rating | Hardness | Yield Strength, psi | Each | |
Inch—1045 Carbon Steel | ||||||||||||
3/4" Dia. (Tolerance: -0.003" to 0") | ||||||||||||
6" | 3/8" | 6" | 5/16"-18 | 0.625" | -0.0625" to 0.0625" | 0.012" per ft. | Chamfered | Medium | Rockwell B90 | 60,000 | 000000 | 000000 |
12" | 3/8" | 12" | 5/16"-18 | 0.625" | -0.0625" to 0.0625" | 0.012" per ft. | Chamfered | Medium | Rockwell B90 | 60,000 | 0000000 | 00000 |
24" | 3/8" | 24" | 5/16"-18 | 0.625" | -0.0625" to 0.0625" | 0.012" per ft. | Chamfered | Medium | Rockwell B90 | 60,000 | 0000000 | 00000 |
36" | 3/8" | 36" | 5/16"-18 | 0.625" | -0.0625" to 0.0625" | 0.012" per ft. | Chamfered | Medium | Rockwell B90 | 60,000 | 0000000 | 00000 |
48" | 3/8" | 48" | 5/16"-18 | 0.625" | -0.0625" to 0.0625" | 0.012" per ft. | Chamfered | Medium | Rockwell B90 | 60,000 | 0000000 | 00000 |
A hollow center allows these studs to be used as an axle, a vent, or a passageway for wiring. Made from 18-8 stainless, they have good chemical resistance and may be mildly magnetic. Thread length is the same on both ends.
For technical drawings and 3-D models, click on a part number.