About Track Rollers
Also known as cam followers, track rollers have a thick outer roller that runs directly on a flat surface.
More
About Ball and Roller Bearings
More
Permanently Lubricated Ball Bearings
A solid polymer lubricant surrounds the balls, eliminating the need for additional lubrication. Because it's solid, the lubricant blocks out water and dust, extending the life of the bearing.
Sealed bearings have even better resistance to dust and contaminants than open bearings.
For technical drawings and 3-D models, click on a part number.
Radial Load Cap., lbs. | ||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|
Bearing Trade Number | For Shaft Dia. | For Housing ID | Wd. | Ring Material | Dynamic | Static | Max. Speed, rpm | Lubrication | Temp. Range, °F | ABEC Rating | Each | |
Open | ||||||||||||
6002 | 15mm | 32mm | 9mm | Steel | 1,050 | 510 | 12,500 | Lubricated | 10° to 200° | ABEC-1 | 00000000 | 000000 |
Sealed | ||||||||||||
6002-2RS | 15mm | 32mm | 9mm | Steel | 1,050 | 510 | 12,500 | Lubricated | 10° to 200° | ABEC-1 | 00000000 | 00000 |
Precision Ball Bearings
For greater accuracy and higher speeds, these bearings are made to tighter tolerances than standard ball bearings.
Shielded bearings dissipate heat more efficiently than sealed bearings.
Sealed bearings block out dust and other contaminants better than shielded bearings.
For technical drawings and 3-D models, click on a part number.
Radial Load Cap., lbs. | ||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|
Bearing Trade Number | For Shaft Dia., mm | For Housing ID, mm | Wd., mm | Ring Material | Dynamic | Static | Max. Speed, rpm | Lubrication | Temp. Range, °F | ABEC Rating | Each | |
Shielded | ||||||||||||
629-2Z | 9 | 26 | 8 | Steel | 1,050 | 440 | 30,000 | Lubricated | -20° to 230° | ABEC-3 | 0000000 | 000000 |
6000-2Z | 10 | 26 | 8 | Steel | 1,050 | 440 | 34,000 | Lubricated | -20° to 230° | ABEC-3 | 0000000 | 00000 |
Sealed | ||||||||||||
6000-2RS | 10 | 26 | 8 | Steel | 1,050 | 440 | 19,000 | Lubricated | -30° to 210° | ABEC-3 | 0000000 | 00000 |
Electrically Insulated Ball Bearings
Good for use in electric motors and power generators, these bearings have ceramic balls that insulate against stray current to prevent damage to the bearing. The ceramic balls generate less heat than steel balls, so they require lubrication less frequently.
Sealed bearings block out dust and other contaminants better than open and shielded bearings but retain the most heat.
For technical drawings and 3-D models, click on a part number.
Radial Load Cap., lbs. | ||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|
Bearing Trade Number | For Shaft Dia., mm | For Housing ID, mm | Wd., mm | Ring Material | Dynamic | Static | Max. Speed, rpm | Lubrication | Temp. Range, °F | ABEC Rating | Each | |
Sealed | ||||||||||||
6000-2RS | 10 | 26 | 8 | Steel | 1,050 | 440 | 32,000 | Lubricated | -40° to 210° | ABEC-1 | 0000000 | 0000000 |
Stainless Steel Ball Bearings
Bearings are 440C stainless steel for good corrosion resistance.
Open bearings dissipate heat more efficiently than shielded and sealed bearings.
Shielded bearings block out dust and other contaminants, but do not dissipate heat as efficiently as open bearings.
Sealed bearings block out dust and other contaminants better than open and shielded bearings, but retain the most heat.
For technical drawings and 3-D models, click on a part number.
Radial Load Cap., lbs. | ||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|
Bearing Trade Number | For Shaft Dia. | For Housing ID | Wd. | Ring Material | Dynamic | Static | Max. Speed, rpm | Lubrication | Temp. Range, °F | ABEC Rating | Each | |
R10 | 5/8" | 1 3/8" | 9/32" | 440C Stainless Steel | 1,050 | 650 | 21,000 | Lubricated | -40° to 240° | ABEC-1 | 0000000 | 000000 |
6002 | 15mm | 32mm | 9mm | 440C Stainless Steel | 1,050 | 510 | 26,000 | Lubricated | -40° to 240° | ABEC-1 | 00000000 | 00000 |
Radial Load Cap., lbs. | ||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|
Bearing Trade Number | For Shaft Dia. | For Housing ID | Wd. | Ring Material | Dynamic | Static | Max. Speed, rpm | Lubrication | Temp. Range, °F | ABEC Rating | Each | |
R10-2Z | 5/8" | 1 3/8" | 11/32" | 440C Stainless Steel | 1,050 | 650 | 21,000 | Lubricated | -40° to 240° | ABEC-1 | 0000000 | 000000 |
6002-2Z | 15mm | 32mm | 9mm | 440C Stainless Steel | 1,050 | 510 | 22,000 | Lubricated | -40° to 240° | ABEC-1 | 00000000 | 00000 |
Radial Load Cap., lbs. | ||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|
Bearing Trade Number | For Shaft Dia. | For Housing ID | Wd. | Ring Material | Dynamic | Static | Max. Speed, rpm | Lubrication | Temp. Range, °F | ABEC Rating | Each | |
R10-2RS | 5/8" | 1 3/8" | 11/32" | 440C Stainless Steel | 1,050 | 650 | 21,000 | Lubricated | -40° to 240° | ABEC-1 | 0000000 | 000000 |
Permanently Lubricated Stainless Steel Ball Bearings
A solid polymer lubricant surrounds the balls, eliminating the need for additional lubrication. The solid lubricant blocks out water and dust, extending the life of the bearing.
Sealed bearings have even better resistance to dust and contaminants than open bearings.
For technical drawings and 3-D models, click on a part number.
Radial Load Cap., lbs. | ||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|
Bearing Trade Number | For Shaft Dia., mm | For Housing ID, mm | Wd., mm | Ring Material | Dynamic | Static | Max. Speed, rpm | Lubrication | Temp. Range, °F | ABEC Rating | Each | |
Open | ||||||||||||
6201 | 12 | 32 | 10 | 440C Stainless Steel | 1,050 | 590 | 13,000 | Lubricated | -10° to 200° | ABEC-1 | 00000000 | 000000 |
Sealed | ||||||||||||
6201-2RS | 12 | 32 | 10 | 440C Stainless Steel | 1,050 | 590 | 13,000 | Lubricated | -10° to 200° | ABEC-1 | 00000000 | 00000 |
Food Industry Permanently Lubricated Stainless Steel Ball Bearings
Good for applications with incidental food contact, these 440C stainless steel bearings have a food-grade, solid polymer lubricant between the balls and ring that eliminates the need for additional lubrication. The solid lubricant blocks out water and dust, extending the life of the bearing.
Sealed bearings have even better resistance to dust and contaminants than open bearings.
For technical drawings and 3-D models, click on a part number.
Radial Load Cap., lbs. | |||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|
Bearing Trade Number | For Shaft Dia., mm | For Housing ID, mm | Wd., mm | Ring Material | Dynamic | Static | Max. Speed, rpm | Lubrication | Temp. Range, °F | ABEC Rating | Specifications Met | Each | |
Sealed | |||||||||||||
6002-2RS | 15 | 32 | 9 | 440C Stainless Steel | 1,050 | 510 | 12,000 | Lubricated | -40° to 200° | ABEC-1 | FDA Compliant 21 CFR 178.3570 | 00000000 | 000000 |
Ultra-Thin Ball Bearings
These bearings have twice as many contact points as angular-contact ball bearings. Fit onto large-diameter hollow shafts to run air and hydraulic lines, electrical wiring, and other components through moving parts in assemblies such as index and rotary tables, packaging equipment, and robotics.
440 stainless steel bearings are more corrosion resistant than steel bearings.
Open bearings dissipate heat more efficiently than shielded bearings.
Shielded bearings block out dust and other contaminants, but do not dissipate heat as efficiently as open bearings.
For technical drawings and 3-D models, click on a part number.
Radial Load Cap., lbs. | Thrust Load Cap., lbs. | Moment Load Cap., ft.-lbs. | |||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
For Shaft Dia. | For Housing ID | Wd. | Dynamic | Static | Dynamic | Static | Dynamic | Static | Max. Speed, rpm | Lubrication | Contact Angle | Temp. Range, °F | ABEC Rating | Each | |
Steel Ring | |||||||||||||||
Open | |||||||||||||||
4" | 4 5/8" | 5/16" | 1,050 | 1,750 | 1,700 | 4,350 | 140 | 310 | 600 | Required | 30° | -60° to 250° | ABEC-1F | 0000000 | 0000000 |
Shielded | |||||||||||||||
35mm | 47mm | 7mm | 1,050 | 850 | Not Rated | Not Rated | Not Rated | Not Rated | 13,000 | Lubricated | __ | -40° to 150° | ABEC-1 | 00000000 | 00000 |
440 Stainless Steel Ring | |||||||||||||||
Open | |||||||||||||||
35mm | 47mm | 7mm | 1,050 | 850 | Not Rated | Not Rated | Not Rated | Not Rated | 16,000 | Lubricated | __ | -50° to 130° | ABEC-1 | 00000000 | 00000 |
Shielded | |||||||||||||||
35mm | 47mm | 7mm | 1,050 | 850 | Not Rated | Not Rated | Not Rated | Not Rated | 13,000 | Lubricated | __ | -40° to 150° | ABEC-1 | 00000000 | 00000 |
Needle-Roller Bearings
Also known as drawn-cup roller bearings, these are our thinnest roller bearings. The outer ring is drawn out to form a lip that holds the bearing together. Bearings take on the shape of their housing and may be oblong prior to installation.
Open bearings dissipate heat more efficiently than sealed bearings.
For technical drawings and 3-D models, click on a part number.
Radial Load Cap., lbs. | |||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|
For Shaft Dia. | For Housing ID | Wd. | Ring Material | Dynamic | Static | Max. Speed, rpm | Lubrication | For Shaft Surface Smoothness (Ra), microinch | Temp. Range, °F | Each | |
Open | |||||||||||
5/16" | 1/2" | 7/16" | Steel | 1,050 | 1,050 | 29,000 | Required | 8 | -40° to 280° | 00000000 | 00000 |
Precision Needle-Roller Bearings
Install these bearings directly onto hardened and ground shafts. They have higher load capacity, speed, and accuracy than standard needle-roller bearings.
Open bearings dissipate heat more efficiently than sealed bearings.
Shaft liners allow you to use the bearing on unhardened and unground shafts.
For technical drawings and 3-D models, click on a part number.
One-Way Locking Needle-Roller Bearing Clutches
The needles in these bearings roll freely in one direction, but lock to transmit torque when the rotation of the shaft is reversed. Also known as drawn-cup roller clutches. An arrow on the lip indicates the rotational direction that locks the bearings.
Triple-row bearings support radial loads.
Bearings with 301 stainless steel springs handle higher temperatures than bearings with acetal springs.
For technical drawings and 3-D models, click on a part number.
Radial Load Cap., lbs. | ||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|
For Shaft Dia. | For Housing ID | Wd. | Ring Material | Dynamic | Static | Max. Speed, rpm | Max. Torque, ft.-lbs. | Lubrication | For Shaft Surface Smoothness (Ra), microinch | Temp. Range, °F | Each | |
Triple Row | ||||||||||||
301 Stainless Steel Springs | ||||||||||||
10mm | 16mm | 20mm | Steel | 1,050 | 850 | 19,000 | 4.2 | Required | 16 | -20° to 250° | 0000000 | 000000 |
Low-Profile Mounted Ball Bearings
Designed with a thin, compact housing, these bearings are good for space-constrained applications.
Sealed bearings block out dust and other contaminants better than shielded bearings.
Shielded bearings dissipate heat more efficiently than sealed bearings.
For technical drawings and 3-D models, click on a part number.
Overall | Radial Load Cap., lbs. | ||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|
For Shaft Dia. | Center Ht. | Ht. | Lg. | Wd. | Hole Ctr.-to-Ctr. | Dynamic | Static | Max. Speed, rpm | Temp. Range, °F | Alignment Style | Lubrication | Each | |
Sealed 440C Stainless Steel Bearings with Aluminum Housing | |||||||||||||
Shaft Mount Type: Press Fit | |||||||||||||
5/8" | 1" | 1 61/64" | 4 1/32" | 41/64" | 3 1/8" | 1,050 | 590 | 10,500 | 0° to 230° | Fixed Alignment | Lubricated | 0000000 | 000000 |
Overall | Radial Load Cap., lbs. | ||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|
For Shaft Dia. | Center Ht. | Ht. | Lg. | Wd. | Hole Ctr.-to-Ctr. | Dynamic | Static | Max. Speed, rpm | Temp. Range, °F | Alignment Style | Lubrication | Each | |
Shielded 440C Stainless Steel Bearings with Aluminum Housing | |||||||||||||
Shaft Mount Type: Press Fit | |||||||||||||
5/8" | 1" | 1 61/64" | 4 1/32" | 41/64" | 3 1/8" | 1,050 | 590 | 21,000 | -30° to 300° | Fixed Alignment | Lubricated | 00000000 | 000000 |
Threaded V-Groove Track Rollers
Thread the stud directly into a component or secure with a nut for through-hole mounting. Rollers are for use with Angle Rails for V-Groove Track Rollers. They handle radial and thrust (top and side) loads and work well in dirty environments because debris falls off the angled rail. Also known as cam followers, track rollers support loads while guiding and positioning work. All rollers are permanently lubricated.
Rollers with a seal block out dust and other contaminants better than shielded rollers, but they hold more heat. Their seal also helps retain lubricant.
For technical drawings and 3-D models, click on a part number.
Roller, mm | Stud, mm | Thread | Shoulder, mm | Groove, mm | Radial Load Cap., lbs. | ||||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
Dia. | Wd. | Dia. | Lg. | Size | Pitch, mm | Lg., mm | Dia. | Lg. | Wd. | Dp. | Max. Speed | Static | Dynamic | Static Thrust Load Cap., lbs. | Max. Temp., °F | Bearing Type | Includes | Each | |
Steel V-Groove Rollers with Seal | |||||||||||||||||||
60 | 31.4 | 14 | 40 | M14 | 2 | 26 | 18 | 1.6 | 20 | 10 | Not Rated | 1,100 | 1,050 | 680 | 225° | Ball | Mounting Hardware | 0000000 | 000000 |