Bearing Type Bearing Type |
|---|
 | Plain |
For Load Direction For Load Direction |
|---|
 | Radial |
 | Combined Radial and Thrust |
For Shaft Type For Shaft Type |
|---|
 | Round |
Mounted Bearing Type Mounted Bearing Type |
|---|
 | Two-Bolt Flange Mount |
Shaft Mount Type Shaft Mount Type |
|---|
| Slip Fit |
Lubrication Lubrication |
|---|
|
Dynamic Radial Load Capacity Dynamic RadialLoad Capacity | Show |
|---|
|
Dynamic Radial Load Capacity Dynamic RadialLoad Capacity | Hide |
|---|
Housing Material Housing Material |
|---|
|
Mounting Hole Center-to-Center Mounting HoleCenter-to-Center |
|---|
|
Maximum Temperature Maximum Temperature |
|---|
|
Bearing Material Bearing Material |
|---|
|
Lubrication Method Lubrication Method |
|---|
|
Material Material |
|---|
|
DFARS (Defense Acquisition Regulations Supplement) DFARS (Defense AcquisitionRegulations Supplement) |
|---|
Minimum Temperature Minimum Temperature |
|---|
|
About Plain Bearings
More
Ultra-Low-Friction Dry-Running Sleeve Bearings
Use these bearings in applications with frequent starts and stops because they operate with very little friction.
Rulon J bearings create the least amount of friction of any bearing that we offer. They handle heavier loads than PTFE bearings.
Note: Dynamic load capacity is the maximum load a bearing can withstand at a given shaft speed. If your application’s load and speed requirements are below the values listed, the bearing will work.
For technical drawings and 3-D models, click on a part number.
| For Housing ID | Lg. | Dynamic Radial Load Capacity | Color | Temperature Range, °F | Each | |
Rulon J Bearings | ||||||
|---|---|---|---|---|---|---|
For 1 1/4" Shaft Dia. | ||||||
| 1 1/2" | 1 1/2" | 1,400 lbs. @ 30 rpm | Gold | -400° to 550° | 0000000 | 000000 |
Chemical-Resistant Dry-Running Flanged Sleeve Bearings
These bearings stand up to a wider range of chemicals than other dry-running flanged sleeve bearings. They are lightweight and strong.
Note: Dynamic load capacity is the maximum load a bearing can withstand at a given shaft speed. If your application’s load and speed requirements are below the values listed, the bearing will work.
For technical drawings and 3-D models, click on a part number.
| For Housing ID | Lg. | Flange OD | Flange Thick. | Dynamic Radial Load Capacity | Dynamic Thrust Load Capacity | Color | Temperature Range, °F | Each | |
PEEK Plastic Bearings | |||||||||
|---|---|---|---|---|---|---|---|---|---|
For 30 mm Shaft Dia. | |||||||||
| 38mm | 20mm | 46mm | 4mm | 1,400 lbs. @ 30 rpm | 1,450 lbs. @ 30 rpm | Beige | -20° to 450° | 00000000 | 000000 |
For 40 mm Shaft Dia. | |||||||||
| 46mm | 20mm | 56mm | 5mm | 1,400 lbs. @ 30 rpm | 1,500 lbs. @ 30 rpm | Beige | -20° to 450° | 00000000 | 00000 |
Extreme-Temperature Dry-Running Mounted Sleeve Bearings with Two-Bolt Flange
Capable of handling temperatures from -400° to 750° F, these graphalloy bearings have the widest temperature range of any of our mounted bearings. They are self-aligning to compensate for shaft misalignment.
Note: Dynamic load capacity is the maximum load a bearing can withstand at a given shaft speed. If your application’s load and speed requirements are below the values listed, the bearing will work.
For technical drawings and 3-D models, click on a part number.
Overall | Mounting | |||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|
| For Shaft Dia. | Ht. | Lg. | Wd. | Bearing Wd. | Flange Thick. | Hole Dia. | Hole Ctr.-to-Ctr. | Dynamic Radial Load Cap. | Temp. Range, °F | Alignment Style | Each | |
Graphalloy Bearings with Cast Iron Housing | ||||||||||||
| 1 1/4" | 3 5/32" | 5 13/16" | 1 1/2" | 1 1/2" | 1/2" | 5/8" | 4 39/64" | 1,400 lbs. @ 30 rpm | -400° to 750° | Self Aligning | 0000000 | 0000000 |