System of Measurement System of Measurement |
---|
|
For Shaft Diameter For Shaft Diameter |
---|
|
Mounted Bearing Type Mounted Bearing Type |
---|
![]() | ![]() |
Base Mount | Two-Bolt Flange Mount |
Bearing Type Bearing Type |
---|
![]() | Plain |
Plain Bearing Type Plain Bearing Type |
---|
![]() | Sleeve |
Alignment Style Alignment Style |
---|
|
Dynamic Radial Load Capacity Dynamic RadialLoad Capacity | Show |
---|
|
Dynamic Radial Load Capacity Dynamic RadialLoad Capacity | Hide |
---|
For Load Direction For Load Direction |
---|
![]() | Radial |
REACH (Registration, Evaluation, Authorization and Restriction of Chemicals) REACH (Registration,Evaluation, Authorization and Restriction of Chemicals) |
---|
|
RoHS (Restriction of Hazardous Substances) RoHS (Restriction ofHazardous Substances) |
---|
|
For Shaft Type For Shaft Type |
---|
![]() | Round |
OD OD |
---|
|
DFARS (Defense Acquisition Regulations Supplement) DFARS (Defense AcquisitionRegulations Supplement) |
---|
About Plain Bearings
More
Panel-Mount Dry-Running Sleeve Bearings

Permanently and securely install these self-clinching bearings into panels, with no need for precision-bored holes or machined mounts. They’re often used in areas with tight space restrictions. Install them into sheet metal panels with an air-powered or hydraulic press. They’re not for use in plastic panels. These bearings are self-aligning to compensate for small amounts of shaft misalignment. Made of acetal plastic, they won’t warp or swell when exposed to water, so they’re good for use in washdown environments.
For technical drawings and 3-D models, click on a part number.
Length | Spline OD | For Minimum Sheet Metal Thickness | Dynamic Radial Load Capacity | Misalignment Capability | Temperature Range, °F | Each | |
Acetal Plastic Bearings | |||||||
---|---|---|---|---|---|---|---|
For 5/8" Shaft Diameter | |||||||
0.77" | 1.11" | 0.058" | 145 lbs. @ 60 rpm | 5° | -40° to 180° | 0000000 | 000000 |
Mounted Sleeve Bearings


A reliable classic—these babbitt bearings are strong and corrosion resistant.
Bearings with split housing have a removable section for easy maintenance.
Note: Dynamic load capacity is the maximum load a bearing can withstand at a given shaft speed. If your application’s load and speed requirements are below the values listed, the bearing will work.
For technical drawings and 3-D models, click on a part number.
Overall | Mounting | |||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
For Shaft Dia. | Center Ht. | Ht. | Lg. | Wd. | Bearing Wd. | Hole Lg. | Hole Wd. | Hole Ctr.-to-Ctr. | Dynamic Radial Load Cap. | Temp. Range, °F | Alignment Style | Lubrication | Each | |
Babbitt Bearings with Solid Cast Iron Housing | ||||||||||||||
5/8" | 13/16" | 1 19/32" | 3 3/4" | 1 5/8" | 1 5/8" | 1/2" | 5/16" | 2 5/8" | 145 lbs. @ 60 rpm | 0° to 130° | Fixed Alignment | Required | 0000000 | 000000 |
Babbitt Bearings with Split Cast Iron Housing | ||||||||||||||
5/8" | 7/8" | 1 3/4" | 4 1/4" | 1 5/8" | 1 5/8" | 1/2" | 5/16" | 3 1/4" | 145 lbs. @ 60 rpm | 0° to 130° | Fixed Alignment | Required | 0000000 | 00000 |
Dry-Running Mounted Sleeve Bearings with Two-Bolt Flange

Embedded lubricant particles increase the load capacity of these bearings while also making them slippery. Bearings are self-aligning to compensate for shaft misalignment.
Acetal sleeve bearings won’t warp or swell when exposed to water, making them good for use in washdown environments.
Note: Dynamic load capacity is the maximum load a bearing can withstand at a given shaft speed. If your application’s load and speed requirements are below the values listed, the bearing will work.
For technical drawings and 3-D models, click on a part number.
Overall | Mounting | |||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|
For Shaft Dia. | Ht. | Lg. | Wd. | Bearing Wd. | Flange Thick. | Hole Dia. | Hole Ctr.-to-Ctr. | Dynamic Radial Load Cap. | Temp. Range, °F | Alignment Style | Each | |
Acetal Plastic Bearings with Aluminum Housing | ||||||||||||
5/8" | 1 5/8" | 3 1/4" | 25/32" | 25/32" | 1/4" | 13/32" | 2 1/2" | 145 lbs. @ 60 rpm | -40° to 180° | Self Aligning | 00000000 | 000000 |