For Load Direction For Load Direction |
---|
![]() | Radial |
![]() | Combined Radial and Thrust |
Ball Bearing Type Ball Bearing Type |
---|
![]() | Standard |
For Shaft Type For Shaft Type |
---|
![]() | Round |
Dynamic Radial Load Capacity Dynamic RadialLoad Capacity | Show |
---|
|
Dynamic Radial Load Capacity Dynamic RadialLoad Capacity | Hide |
---|
Construction Construction |
---|
|
Ring Material Ring Material |
---|
|
Cage Material Cage Material |
---|
|
DFARS (Defense Acquisition Regulations Supplement) DFARS (Defense AcquisitionRegulations Supplement) |
---|
Static Thrust Load Capacity Static Thrust Load Capacity |
---|
|
Lubrication Lubrication |
---|
|
Shaft Mount Type Shaft Mount Type |
---|
|
REACH (Registration, Evaluation, Authorization and Restriction of Chemicals) REACH (Registration,Evaluation, Authorization and Restriction of Chemicals) |
---|
|
RoHS (Restriction of Hazardous Substances) RoHS (Restriction ofHazardous Substances) |
---|
|
About Ball and Roller Bearings
More
Self-Aligning Ball Bearings

With a spherical raceway and two rows of balls, these bearings compensate for shaft misalignment.
Sealed bearings block out dust and other contaminants better than open bearings, but retain more heat.
For technical drawings and 3-D models, click on a part number.
Radial Load Cap., lbs. | |||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|
Bearing Trade Number | For Shaft Dia., mm | For Housing ID, mm | Wd., mm | Ring Material | Dynamic | Static | Max. Speed, rpm | Lubrication | Misalignment Capability | Temp. Range, °F | ABEC Rating | Each | |
Sealed | |||||||||||||
2207-2RS | 35 | 72 | 23 | Steel | 4,250 | 1,300 | 6,300 | Lubricated | 1.5° | -30° to 210° | ABEC-1 | 0000000 | 0000000 |
2305-2RS | 25 | 62 | 24 | Steel | 4,250 | 1,200 | 7,500 | Lubricated | 1.5° | -30° to 210° | ABEC-1 | 0000000 | 000000 |
Ultra-Thin Ball Bearings


These bearings have twice as many contact points as angular-contact ball bearings. Fit onto large-diameter hollow shafts to run air and hydraulic lines, electrical wiring, and other components through moving parts in assemblies such as index and rotary tables, packaging equipment, and robotics.
Open bearings dissipate heat more efficiently than shielded bearings.
Shielded bearings block out dust and other contaminants, but do not dissipate heat as efficiently as open bearings.
For technical drawings and 3-D models, click on a part number.
Radial Load Cap., lbs. | Thrust Load Cap., lbs. | Moment Load Cap., ft.-lbs. | ||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
For Shaft Dia. | For Housing ID | Wd. | Dynamic | Static | Dynamic | Static | Dynamic | Static | Max. Speed, rpm | Lubrication | Temp. Range, °F | ABEC Rating | Each | |
Steel Ring | ||||||||||||||
Open | ||||||||||||||
90mm | 115mm | 13mm | 4,250 | 4,400 | Not Rated | Not Rated | Not Rated | Not Rated | 6,300 | Lubricated | -50° to 130° | ABEC-1 | 00000000 | 0000000 |
Shielded | ||||||||||||||
90mm | 115mm | 13mm | 4,250 | 4,400 | Not Rated | Not Rated | Not Rated | Not Rated | 5,300 | Lubricated | -40° to 150° | ABEC-1 | 00000000 | 000000 |
Combination Ball/Needle-Roller Bearings


A built-in thrust ball bearing reduces wear from adjacent shaft components, while the needle rollers support high radial loads. Install anywhere you would use separate bearings for radial and thrust loads.
For technical drawings and 3-D models, click on a part number.
Radial Load Cap., lbs. | Thrust Load Cap., lbs. | ||||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
For Shaft Dia., mm | For Housing ID, mm | Wd., mm | Ball Bearing OD, mm | Ball Bearing Wd., mm | Ring Material | Dynamic | Static | Dynamic | Static | Max. Speed, rpm | Lubrication | For Shaft Surface Smoothness (Ra), microinch | Temp. Range, °F | Each | |
Open | |||||||||||||||
25 | 37 | 30 | 43 | 11 | Steel | 4,250 | 6,700 | 4,050 | 6,670 | 6,300 | Required | 8 | -20° to 230° | 00000000 | 000000 |
Needle-Roller Bearings

Also known as drawn-cup roller bearings, these are our thinnest roller bearings. The outer ring is drawn out to form a lip that holds the bearing together. Bearings take on the shape of their housing and may be oblong prior to installation.
Open bearings dissipate heat more efficiently than sealed bearings.
For technical drawings and 3-D models, click on a part number.
Radial Load Cap., lbs. | |||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|
For Shaft Dia. | For Housing ID | Wd. | Ring Material | Dynamic | Static | Max. Speed, rpm | Lubrication | For Shaft Surface Smoothness (Ra), microinch | Temp. Range, °F | Each | |
Open | |||||||||||
1 1/8" | 1 3/8" | 3/4" | Steel | 4,250 | 7,700 | 9,800 | Required | 8 | -40° to 280° | 00000000 | 000000 |