About Plain Bearings
More
Oil-Embedded Sleeve Bearings
Startup friction causes these porous bronze bearings to release a thin layer of oil on the bearing’s surface. They are also known as Oilite® bearings.
Note: Dynamic load capacity is the maximum load a bearing can withstand at a given shaft speed. If your application’s load and speed requirements are below the values listed, the bearing will work.
For technical drawings and 3-D models, click on a part number.
For Housing ID | Lg. | Dynamic Radial Load Capacity | Lubrication | Lubricant | Temperature Range, °F | Each | |
For 3/16" Shaft Dia. | |||||||
---|---|---|---|---|---|---|---|
5/16" | 3/16" | 70 lbs. @ 120 rpm | Lubricated | SAE 30 Oil | -35° to 300° | 00000000 | 00000 |
For Housing ID, mm | Lg., mm | Dynamic Radial Load Capacity | Lubrication | Lubricant | Temperature Range, °F | Each | |
For 4 mm Shaft Dia. | |||||||
---|---|---|---|---|---|---|---|
7 | 6 | 70 lbs. @ 120 rpm | Lubricated | SAE 30 Oil | -35° to 300° | 0000000 | 00000 |
8 | 6 | 70 lbs. @ 120 rpm | Lubricated | SAE 30 Oil | -35° to 300° | 00000000 | 0000 |
For 6 mm Shaft Dia. | |||||||
9 | 4 | 70 lbs. @ 120 rpm | Lubricated | SAE 30 Oil | -35° to 300° | 00000000 | 0000 |
10 | 4 | 70 lbs. @ 120 rpm | Lubricated | SAE 30 Oil | -35° to 300° | 00000000 | 0000 |
High-Load Oil-Embedded Sleeve Bearings
Increased iron content makes these bearings stronger and more resistant to shock loads than standard oil-embedded bearings; however they operate at lower speeds. Startup friction causes them to release a thin layer of oil on the bearing’s surface. Color is silver because of the iron. These bearings are also magnetic due to the high iron content.
863 iron-copper bearings are also known as Super Oilite® bearings.
Note: Dynamic load capacity is the maximum load a bearing can withstand at a given shaft speed. If your application’s load and speed requirements are below the values listed, the bearing will work.
For technical drawings and 3-D models, click on a part number.
For Housing ID | Lg. | Dynamic Radial Load Capacity | Lubrication | Lubricant | Temperature Range, °F | Each | |
For 3mm Shaft Dia. | |||||||
---|---|---|---|---|---|---|---|
6mm | 4mm | 70 lbs. @ 120 rpm | Lubricated | SAE 90 Oil | -15° to 300° | 00000000 | 00000 |
Ultra-Low-Friction Oil-Embedded Sleeve Bearings
For applications with frequent starts and stops, the oil in these bearings contains particles of slippery PTFE that lubricate the bearing during startup.
Note: Dynamic load capacity is the maximum load a bearing can withstand at a given shaft speed. If your application’s load and speed requirements are below the values listed, the bearing will work.
For technical drawings and 3-D models, click on a part number.
For Housing ID, mm | Lg., mm | Dynamic Radial Load Capacity | Lubrication | Lubricant | Temperature Range, °F | Each | |
For 4mm Shaft Dia. | |||||||
---|---|---|---|---|---|---|---|
7 | 6 | 70 lbs. @ 120 rpm | Lubricated | SAE 20 Oil with PTFE | -60° to 300° | 00000000 | 00000 |
Panel-Mount Oil-Embedded Sleeve Bearings
Unlike other sleeve bearings, these do not need to be fully inserted into a housing. Their unique shape creates a permanent, secure hold in thin panels. Bearings swivel to accommodate up to 5° of shaft misalignment. On startup, friction causes the bronze to release a thin layer of oil on the bearing’s surface. Not for use with plastic panels.
Note: Dynamic load capacity is the maximum load a bearing can withstand at a given shaft speed. If your application’s load and speed requirements are below the values listed, the bearing will work.
For technical drawings and 3-D models, click on a part number.
Lg. | Spline OD | For Min. Sheet Metal Thick. | Dynamic Radial Load Capacity | Misalignment Capability | Lubrication | Lubricant | Temperature Range, °F | Each | |
840 Bronze Bearings | |||||||||
---|---|---|---|---|---|---|---|---|---|
For 1/8" Shaft Dia. | |||||||||
0.29" | 0.39" | 0.04" | 70 lbs. @ 120 rpm | 5° | Lubricated | SAE 45 Oil | -20° to 200° | 0000000 | 000000 |
High-Load Ultra-Low-Friction Oil-Embedded Sleeve Bearings
With extra iron and filled with oil containing slippery PTFE, these bearings support heavy loads that frequently start and stop along shafts. Startup friction causes a thin layer of oil to release onto the surface. Their high iron content also means they resist failing if their load suddenly and drastically increases, but they won’t run as fast as standard bearings.
Note: Dynamic load capacity is the maximum load a bearing can withstand at a given shaft speed. If your application’s load and speed requirements are below the values listed, the bearing will work.
For technical drawings and 3-D models, click on a part number.
For Housing ID, mm | Length, mm | Dynamic Radial Load Capacity | Lubrication | Lubricant | Temperature Range, °F | Each | |
863 Iron-Copper | |||||||
---|---|---|---|---|---|---|---|
For 3 mm Shaft Dia. | |||||||
6 | 4 | 70 lbs. @ 120 rpm | Lubricated | SAE 20 Oil with PTFE | -60° to 300° | 00000000 | 00000 |
Food Industry Oil-Embedded Sleeve Bearings
The oil in these bearings is suitable for incidental contact with food. Startup friction produces a thin layer of oil on the bearing’s surface.
Note: Dynamic load capacity is the maximum load a bearing can withstand at a given shaft speed. If your application’s load and speed requirements are below the values listed, the bearing will work.
For technical drawings and 3-D models, click on a part number.
For Housing ID | Lg. | Dynamic Radial Load Capacity | Lubrication | Lubricant | Temperature Range, °F | Each | |
For 4mm Shaft Dia. | |||||||
---|---|---|---|---|---|---|---|
7mm | 6mm | 70 lbs. @ 120 rpm | Lubricated | SAE 20 Oil | -75° to 300° | 00000000 | 00000 |
High-Load Food Industry Oil-Embedded Sleeve Bearings
Embedded with oil that is safe for incidental contact with food, these bearings are suitable for use in high-load applications such as bottling and filling lines in food processing plants. They are also known as Super Oilite® bearings. Startup friction releases the embedded oil onto their surface in a thin layer. Bearings are made of 863 iron-copper, which makes these bearings strong and resistant to shock loads.
Bearings with NSF H1 registered lubrication comply with NSF standards for incidental contact with food.
For technical drawings and 3-D models, click on a part number.
For Housing ID | Length | Dynamic Radial Load Capacity | Lubrication | Lubricant | Temperature Range, °F | Specifications Met | Each | |
863 Iron-Copper | ||||||||
---|---|---|---|---|---|---|---|---|
For 3mm Shaft Dia. | ||||||||
6mm | 4mm | 70 lbs. @ 120 rpm | Lubricated | SAE 20 Oil | -75° to 300° | ASTM B439, NSF Registered H1 | 00000000 | 00000 |
Light Duty Dry-Running Sleeve Bearings
Use where high loads and speeds are not required.
MDS-filled nylon bearings create less friction than standard nylon bearings, making them more wear resistant.
Note: Dynamic load capacity is the maximum load a bearing can withstand at a given shaft speed. If your application’s load and speed requirements are below the values listed, the bearing will work.
For technical drawings and 3-D models, click on a part number.
For Housing ID | Lg. | Dynamic Radial Load Capacity | Color | Temperature Range, °F | Each | |
Nylon Bearings | ||||||
---|---|---|---|---|---|---|
For 3/8" Shaft Dia. | ||||||
1/2" | 3/4" | 70 lbs. @ 120 rpm | White | -10° to 220° | 00000000 | 00000 |
5/8" | 3/4" | 70 lbs. @ 120 rpm | White | -10° to 220° | 00000000 | 0000 |
For 1/2" Shaft Dia. | ||||||
5/8" | 3/4" | 70 lbs. @ 120 rpm | White | -10° to 220° | 00000000 | 0000 |
3/4" | 3/4" | 70 lbs. @ 120 rpm | White | -10° to 220° | 00000000 | 0000 |
MDS-Filled Nylon Bearings | ||||||
For 3/8" Shaft Dia. | ||||||
5/8" | 3/4" | 70 lbs. @ 120 rpm | Black | -40° to 170° | 000000 | 0000 |
For 1/2" Shaft Dia. | ||||||
3/4" | 3/4" | 70 lbs. @ 120 rpm | Black | -40° to 170° | 000000 | 0000 |
Ultra-Low-Friction Dry-Running Sleeve Bearings
Use these bearings in applications with frequent starts and stops because they operate with very little friction.
Rulon J bearings create the least amount of friction of any bearing that we offer. They handle heavier loads than PTFE bearings.
Note: Dynamic load capacity is the maximum load a bearing can withstand at a given shaft speed. If your application’s load and speed requirements are below the values listed, the bearing will work.
For technical drawings and 3-D models, click on a part number.
For Housing ID | Lg. | Dynamic Radial Load Capacity | Color | Temperature Range, °F | Each | |
Rulon J Bearings | ||||||
---|---|---|---|---|---|---|
For 3/16" Shaft Dia. | ||||||
1/4" | 1/2" | 70 lbs. @ 120 rpm | Gold | -400° to 550° | 000000 | 000000 |
5/16" | 1/2" | 70 lbs. @ 120 rpm | Gold | -400° to 550° | 0000000 | 0000 |
For 1/4" Shaft Dia. | ||||||
3/8" | 3/8" | 70 lbs. @ 120 rpm | Gold | -400° to 550° | 0000000 | 0000 |
Metric Rulon J Bearings | ||||||
For 8mm Shaft Dia. | ||||||
12mm | 8mm | 70 lbs. @ 120 rpm | Gold | -400° to 550° | 00000000 | 00000 |
Food Industry Dry-Running Sleeve Bearings
Made of FDA-listed materials or FDA compliant, these bearings are for use in food applications. They also withstand caustic and washdown environments.
Rulon 641 bearings are stronger than UHMW and acetal bearings, and withstand a wider range of temperatures.
Note: Dynamic load capacity is the maximum load a bearing can withstand at a given shaft speed. If your application’s load and speed requirements are below the values listed, the bearing will work.
For technical drawings and 3-D models, click on a part number.
For Housing ID | Lg. | Dynamic Radial Load Capacity | Color | Temperature Range, °F | Specifications Met | Each | |
Rulon 641 Plastic Bearings | |||||||
---|---|---|---|---|---|---|---|
For 3/16" Shaft Dia. | |||||||
5/16" | 3/8" | 70 lbs. @ 120 rpm | White | -400° to 550° | FDA Compliant 21 CFR 177.1550, USP Class VI | 000000 | 000000 |
Chemical-Resistant Dry-Running Sleeve Bearings
These bearings stand up to a wider range of chemicals than other dry-running sleeve bearings.
Glass-filled PTFE bearings have the same low-friction properties as PTFE bearings, along with increased load capacity.
Note: Dynamic load capacity is the maximum load a bearing can withstand at a given shaft speed. If your application’s load and speed requirements are below the values listed, the bearing will work.
For technical drawings and 3-D models, click on a part number.
For Housing ID | Lg. | Dynamic Radial Load Cap. | Color | Temp. Range, °F | Each | |
Glass-Filled PTFE Plastic Bearings | ||||||
---|---|---|---|---|---|---|
For 3/16" Shaft Dia. | ||||||
5/16" | 3/8" | 70 lbs. @ 120 rpm | White | -350° to 500° | 000000 | 00000 |
Water-Resistant Dry-Running Sleeve Bearings
Good for underwater applications, these bearings won’t swell or warp when wet.
Note: Dynamic load capacity is the maximum load a bearing can withstand at a given shaft speed. If your application’s load and speed requirements are below the values listed, the bearing will work.
For technical drawings and 3-D models, click on a part number.
Oil-Embedded Flanged Sleeve Bearings
Startup friction causes these porous bronze bearings to release a thin layer of oil on the bearing’s surface. They are also known as Oilite® bearings.
Note: Dynamic load capacity is the maximum load a bearing can withstand at a given shaft speed. If your application’s load and speed requirements are below the values listed, the bearing will work.
For technical drawings and 3-D models, click on a part number.
For Housing ID | Lg. | Flange OD | Flange Thick. | Dynamic Radial Load Capacity | Dynamic Thrust Load Capacity | Lubrication | Lubricant | Temperature Range, °F | Each | |
Metric 841 Bearing Bronze Bearings | ||||||||||
---|---|---|---|---|---|---|---|---|---|---|
For 4mm Shaft Dia. | ||||||||||
7mm | 6mm | 10mm | 1.5mm | 70 lbs. @ 120 rpm | 200 lbs. @ 120 rpm | Lubricated | SAE 30 Oil | -35° to 300° | 0000000 | 00000 |
For 6mm Shaft Dia. | ||||||||||
10mm | 4mm | 14mm | 2mm | 70 lbs. @ 120 rpm | 380 lbs. @ 120 rpm | Lubricated | SAE 30 Oil | 10° to 220° | 00000000 | 0000 |
High-Load Oil-Embedded Flanged Sleeve Bearings
Increased iron content makes these bearings stronger and more resistant to shock loads than standard oil-embedded bearings; however they operate at lower speeds. Startup friction causes these bearings to release a thin layer of oil onto their surface. Color is silver because of the iron.
863 iron-copper bearings are also known as Super Oilite® bearings.
Note: Dynamic load capacity is the maximum load a bearing can withstand at a given shaft speed. If your application’s load and speed requirements are below the values listed, the bearing will work.
For technical drawings and 3-D models, click on a part number.
For Housing ID | Lg. | Flange OD | Flange Thick. | Dynamic Radial Load Capacity | Dynamic Thrust Load Capacity | Lubrication | Lubricant | Temperature Range, °F | Each | |
863 Iron-Copper Bearings | ||||||||||
---|---|---|---|---|---|---|---|---|---|---|
For 3mm Shaft Dia. | ||||||||||
6mm | 4mm | 9mm | 1.5mm | 70 lbs. @ 120 rpm | 270 lbs. @ 120 rpm | Lubricated | ISO 460 Oil | -15° to 300° | 0000000 | 00000 |
Ultra-Low-Friction Oil-Embedded Flanged Sleeve Bearings
For applications with frequent starts and stops, the oil in these bearings contains particles of slippery PTFE that lubricate the bearing during startup.
Note: Dynamic load capacity is the maximum load a bearing can withstand at a given shaft speed. If your application’s load and speed requirements are below the values listed, the bearing will work.
For technical drawings and 3-D models, click on a part number.
For Housing ID | Lg. | Flange OD | Flange Thick. | Dynamic Radial Load Capacity | Dynamic Thrust Load Capacity | Lubrication | Lubricant | Temperature Range, °F | Each | |
841 Bronze Bearings | ||||||||||
---|---|---|---|---|---|---|---|---|---|---|
For 3/16" Shaft Dia. | ||||||||||
5/16" | 3/16" | 7/16" | 1/16" | 70 lbs. @ 120 rpm | 240 lbs. @ 120 rpm | Lubricated | ISO 68 Oil | -140° to 460° | 00000000 | 00000 |
For 4mm Shaft Dia. | ||||||||||
7mm | 6mm | 10mm | 1.5mm | 70 lbs. @ 120 rpm | 200 lbs. @ 120 rpm | Lubricated | SAE 20 Oil with PTFE | -60° to 300° | 00000000 | 0000 |
High-Load Ultra-Low-Friction Oil-Embedded Flanged Sleeve Bearings
With oil for reduced friction and iron for added strength, these bearings handle frequent stops and starts in high-load applications. They withstand greater weight and shock loads than standard bearings, but operate at lower speeds.
For technical drawings and 3-D models, click on a part number.
For Housing ID, mm | Length, mm | Flange OD, mm | Flange Thickness, mm | Dynamic Radial Load Capacity | Dynamic Thrust Load Capacity | Lubrication | Lubricant | Temperature Range, °F | Each | |
863 Iron-Copper Bearings | ||||||||||
---|---|---|---|---|---|---|---|---|---|---|
3 mm Shaft Dia. | ||||||||||
6 | 4 | 9 | 1.5 | 70 lbs. @ 120 rpm | 270 lbs. @ 120 rpm | Lubricated | ISO 460 Oil | -60° to 300° | 00000000 | 00000 |
Food Industry Oil-Embedded Flanged Sleeve Bearings
The oil in these bearings is suitable for incidental contact with food. Startup friction produces a thin layer of oil on the bearing’s surface.
Note: Dynamic load capacity is the maximum load a bearing can withstand at a given shaft speed. If your application’s load and speed requirements are below the values listed, the bearing will work.
For technical drawings and 3-D models, click on a part number.
For Housing ID | Lg. | Flange OD | Flange Thick. | Dynamic Radial Load Capacity | Dynamic Thrust Load Capacity | Lubrication | Lubricant | Temperature Range, °F | Specifications Met | Each | |
841 Bronze Bearings | |||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|
For 4mm Shaft Dia. | |||||||||||
7mm | 6mm | 10mm | 1.5mm | 70 lbs. @ 120 rpm | 200 lbs. @ 120 rpm | Lubricated | SAE 20 Oil | -75° to 300° | FDA Compliant 21 CFR 178.3570 | 0000000 | 00000 |
High-Load Food Industry Oil-Embedded Flanged Sleeve Bearings
Support heavy loads that are often found in bottling and filling lines in food plants—these bearings contain extra iron and FDA-compliant oil. The oil is safe to touch food, though it shouldn’t regularly come in contact. Startup friction causes these bearings to release a thin layer of oil onto their surface. They’re flanged, so they handle loads both parallel and perpendicular to the shaft.
841 bearing bronze bearings run at higher speeds than 863 iron-copper bearings. They’re also known as Oilite® bearings.
For technical drawings and 3-D models, click on a part number.
For Housing ID | Length | Flange OD | Flange Thickness | Dynamic Radial Load Capacity | Dynamic Thrust Load Capacity | Lubrication | Lubricant | Temperature Range, °F | Specifications Met | Each | |
841 Bearing Bronze Bearings | |||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|
For 4mm Shaft Dia. | |||||||||||
7mm | 6mm | 10mm | 1.5mm | 70 lbs. @ 120 rpm | 200 lbs. @ 120 rpm | Lubricated | SAE 20 Oil | -75° to 300° | FDA Compliant 21 CFR 178.3570 | 00000000 | 00000 |
Light Duty Dry-Running Flanged Sleeve Bearings
Use where high loads and speeds are not required.
MDS-filled nylon bearings create less friction than standard nylon bearings, making them more wear resistant.
Thermoplastic-blend bearings have low moisture absorption and create very low friction in applications with light loads, and frequent starts and stops.
Note: Dynamic load capacity is the maximum load a bearing can withstand at a given shaft speed. If your application’s load and speed requirements are below the values listed, the bearing will work.
For technical drawings and 3-D models, click on a part number.
For Housing ID | Lg. | Flange OD | Flange Thick. | Dynamic Radial Load Capacity | Dynamic Thrust Load Capacity | Color | Temperature Range, °F | Each | |
Nylon Bearings | |||||||||
---|---|---|---|---|---|---|---|---|---|
For 3/8" Shaft Dia. | |||||||||
1/2" | 3/4" | 5/8" | 1/16" | 70 lbs. @ 120 rpm | 30 lbs. @ 120 rpm | White | -20° to 250° | 00000000 | 00000 |
1/2" | 3/4" | 5/8" | 1/8" | 70 lbs. @ 120 rpm | 30 lbs. @ 120 rpm | White | -20° to 250° | 00000000 | 0000 |
5/8" | 3/4" | 7/8" | 1/8" | 70 lbs. @ 120 rpm | 50 lbs. @ 120 rpm | White | -20° to 250° | 00000000 | 0000 |
For 1/2" Shaft Dia. | |||||||||
5/8" | 3/4" | 3/4" | 1/16" | 70 lbs. @ 120 rpm | 31 lbs. @ 120 rpm | White | -20° to 250° | 00000000 | 0000 |
5/8" | 3/4" | 7/8" | 1/16" | 70 lbs. @ 120 rpm | 44 lbs. @ 120 rpm | White | -20° to 250° | 00000000 | 0000 |
3/4" | 3/4" | 7/8" | 1/16" | 70 lbs. @ 120 rpm | 44 lbs. @ 120 rpm | White | -20° to 250° | 00000000 | 0000 |
MDS-Filled Nylon Bearings | |||||||||
For 3/8" Shaft Dia. | |||||||||
1/2" | 3/4" | 5/8" | 1/8" | 70 lbs. @ 120 rpm | 30 lbs. @ 120 rpm | Black | -40° to 170° | 00000000 | 0000 |
5/8" | 3/4" | 7/8" | 1/8" | 70 lbs. @ 120 rpm | 50 lbs. @ 120 rpm | Black | -40° to 170° | 00000000 | 0000 |
For 1/2" Shaft Dia. | |||||||||
5/8" | 3/4" | 3/4" | 1/16" | 70 lbs. @ 120 rpm | 31 lbs. @ 120 rpm | Black | -40° to 170° | 00000000 | 0000 |
3/4" | 3/4" | 7/8" | 1/16" | 70 lbs. @ 120 rpm | 44 lbs. @ 120 rpm | Black | -40° to 170° | 00000000 | 0000 |
Thermoplastic-Blend Bearings | |||||||||
For 4mm Shaft Dia. | |||||||||
5.5mm | 6mm | 9.5mm | 0.75mm | 70 lbs. @ 120 rpm | 70 lbs. @ 120 rpm | Yellow | -50° to 190° | 00000000 | 0000 |
For 6mm Shaft Dia. | |||||||||
8mm | 6mm | 12mm | 1mm | 70 lbs. @ 120 rpm | 85 lbs. @ 120 rpm | Yellow | -50° to 190° | 00000000 | 0000 |
For 8mm Shaft Dia. | |||||||||
10mm | 6mm | 15mm | 1mm | 70 lbs. @ 120 rpm | 100 lbs. @ 120 rpm | Yellow | -50° to 190° | 00000000 | 0000 |
Ultra-Low-Friction Dry-Running Flanged Sleeve Bearings
Use these bearings in applications with frequent starts and stops because they operate with very little friction.
Rulon J bearings create the least amount of friction of any bearing that we offer. They handle heavier loads than PTFE bearings.
Note: Dynamic load capacity is the maximum load a bearing can withstand at a given shaft speed. If your application’s load and speed requirements are below the values listed, the bearing will work.
For technical drawings and 3-D models, click on a part number.
For Housing ID | Lg. | Flange OD | Flange Thick. | Dynamic Radial Load Capacity | Dynamic Thrust Load Capacity | Color | Temperature Range, °F | Each | |
Rulon J Plastic Bearings | |||||||||
---|---|---|---|---|---|---|---|---|---|
For 3/16" Shaft Dia. | |||||||||
1/4" | 1/2" | 3/8" | 1/32" | 70 lbs. @ 120 rpm | 50 lbs. @ 120 rpm | Gold | -400° to 550° | 00000000 | 000000 |
5/16" | 1/2" | 7/16" | 1/16" | 70 lbs. @ 120 rpm | 65 lbs. @ 120 rpm | Gold | -400° to 550° | 0000000 | 0000 |
For 1/4" Shaft Dia. | |||||||||
3/8" | 3/8" | 1/2" | 1/16" | 70 lbs. @ 120 rpm | 70 lbs. @ 120 rpm | Gold | -400° to 550° | 0000000 | 0000 |
Chemical-Resistant Dry-Running Flanged Sleeve Bearings
These bearings stand up to a wider range of chemicals than other dry-running flanged sleeve bearings. They are lightweight and strong.
Note: Dynamic load capacity is the maximum load a bearing can withstand at a given shaft speed. If your application’s load and speed requirements are below the values listed, the bearing will work.
For technical drawings and 3-D models, click on a part number.
For Housing ID | Lg. | Flange OD | Flange Thick. | Dynamic Radial Load Capacity | Dynamic Thrust Load Capacity | Color | Temperature Range, °F | Each | |
PEEK Plastic Bearings | |||||||||
---|---|---|---|---|---|---|---|---|---|
For 3 mm Shaft Dia. | |||||||||
6mm | 4mm | 9mm | 1.5mm | 70 lbs. @ 120 rpm | 110 lbs. @ 120 rpm | Beige | -20° to 450° | 00000000 | 000000 |
Multipurpose Flanged Sleeve Bearings
These bronze bearings are strong, wear resistant, and excellent at handling shock loads. They’re sometimes called 660 leaded bronze bearings.
Note: Dynamic load capacity is the maximum load a bearing can withstand at a given shaft speed. If your application’s load and speed requirements are below the values listed, the bearing will work.
For technical drawings and 3-D models, click on a part number.
For Housing ID | Lg. | Flange OD | Flange Thick. | Dynamic Radial Load Capacity | Dynamic Thrust Load Capacity | Lubrication | Temperature Range, °F | PV Max. | Each | |
Metric 932 Bearing Bronze Bearings | ||||||||||
---|---|---|---|---|---|---|---|---|---|---|
For 3mm Shaft Dia. | ||||||||||
6mm | 4mm | 9mm | 1.5mm | 70 lbs. @ 120 rpm | 350 lbs. @ 120 rpm | Required | -350° to 450° | 75,000 | 00000000 | 00000 |
High-Speed Light Duty Dry-Running Mounted
Sleeve Bearings with Two-Bolt Flange
Made of acetal with a PTFE filling, these light duty bearings handle speeds twice as fast as standard acetal bearings can. The material is self-lubricating for less wear and longer life in your system. These bearings swivel to compensate for small amounts of shaft misalignment.
For technical drawings and 3-D models, click on a part number.
Overall | Mounting | |||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|
For Shaft Diameter | Height | Length | Width | Bearing Width | Flange Thickness | Hole Diameter | Hole Center-to-Center | Dynamic Radial Load Capacity | Temperature Range, °F | Alignment Style | Each | |
PTFE-Filled Acetal Plastic Bearings with Black-Oxide Steel Housing | ||||||||||||
5/16" | 1 3/16" | 2 3/32" | 25/64" | 21/64" | 1/16" | 7/32" | 1 17/32" | 85 lbs. @ 120 rpm | -40° to 180° | Self Aligning | 0000000 | 000000 |
8mm | 30.3mm | 53.4mm | 10mm | 8.5mm | 1.5mm | 5.6mm | 38.9mm | 85 lbs. @ 120 rpm | -40° to 180° | Self Aligning | 000000 | 00000 |