6.1mm ID Bearings | McMaster-Carr

Filter by

System of Measurement

Length

Plain Bearing Type

Shaft Diameter

Drill Bushing Type

Material

RoHS Compliance

DFARS Compliance

Installation Permanence

Drill Bushing Texture

Hardness

Internal Chamfer

For Housing ID

Drill Bit Size

Bearing Type

Dynamic Radial Load Capacity @ Speed

For Load Direction

Lubrication

Shaft Mount Type

Shaft Type

Specifications Met

Forward

How can we improve?

10 Products

About Plain Bearings

Good for underwater applications, these bearings won’t swell or warp when wet.

Note: Dynamic load capacity is the maximum load a bearing can withstand at a given shaft speed. If your application’s load and speed requirements are below the values listed, the bearing will work.

For technical drawings and 3-D models, click on a part number.

Rulon LR Plastic Bearings
ID	For Housing ID	Lg.	Dynamic Radial Load Capacity	Color	Temperature Range, °F		Each
For 6mm Shaft Dia.
6.1mm	12mm	10mm	90 lbs. @ 120 rpm	Maroon	-400° to 550°	000000	000000

Metric Press-Fit Drill Bushings

Also known as jig bushings, these metric drill bushings fit inside fixture plate holes to guide drill bits, counterbores, reamers, and other cutting tools. They improve accuracy so that your drilled holes and cuts are consistent from part to part. Known for their versatility, drill bushings are also used as spacers, shims, and machinery bushings. These bushings are made of hardened, ground steel that holds its shape and resists wear, so they last for many cycles without needing to be replaced.

All bushings have a chamfer on the outside that centers the bushing as you place it into the hole. Press into place with a manual or hydraulic press. They also have internal chamfers, so it's easier to insert bits, pins, and punches into the bushing. Some bushings have internal chamfers on both ends, so no matter which end of the bushing is inserted into your jig, your bits, pins, and other tooling enter easily. Having an internal chamfer on the bottom of your bushing may cause shavings to get caught and bind as you remove the bit, however.

DIN 179 bushings meet dimensional and material standards that make sure they're compatible with other parts and tools. Although DIN 179 is no longer an active standard, it's still a common reference point for designers.

Don't see the size you need? Additional sizes are available.

For technical drawings and 3-D models, click on a part number.

				Tolerance								Each
OD, mm	Lg., mm	Internal Chamfer	For Drill Bit Size	ID, mm	OD, mm	Lg., mm	Drill Bushing Type	Material	Hardness	Specifications Met		1-5	6-11	12-Up
6.1 mm ID
12	10	Both Ends	6.1 mm	0.013 to 0.028	0.012 to 0.023	-0.2 to 0.2	PM	Steel	Rockwell C61	__	000000000	000000	00000	00000
12	10	One End	6.1 mm	0.005 to 0.014	0.012 to 0.023	-0.4 to 0.4	PM	Steel	Rockwell C61	__	00000000	00000	00000	0000
12	16	Both Ends	6.1 mm	0.013 to 0.028	0.012 to 0.023	-0.2 to 0.2	PM	Steel	Rockwell C61	__	000000000	00000	0000	0000
12	16	One End	6.1 mm	0.013 to 0.028	0.012 to 0.023	-0.2 to 0.2	PM	Steel	Rockwell C61	DIN 179	000000000	00000	0000	0000
12	20	Both Ends	6.1 mm	0.013 to 0.028	0.012 to 0.023	-0.2 to 0.2	PM	Steel	Rockwell C61	__	000000000	00000	00000	00000
12	20	One End	6.1 mm	0.013 to 0.028	0.012 to 0.023	-0.2 to 0.2	PM	Steel	Rockwell C61	DIN 179	000000000	00000	00000	00000

Metric Press-Fit Drill Bushings with Head

Shown in Countersunk Hole

Shown in Standard Hole

Even under extreme drilling pressure, these metric bushings won't press through your jig plate. A flanged head on the top of the bushing acts as a stop, preventing it from moving as you push down your drill bit, reamer, or other cutting bit. Drill bushings ensure accurate, consistent cuts and drilled holes from one part to the next. They sometimes also work as spacers, shims, and machinery bushings. Made of hardened, ground steel, these bushings hold their shape and resist wear over time. The flanged head protects your jig plate from damage caused by heavy use.

Although it's no longer an active standard, DIN 172 is still a common reference point for making sure parts are compatible with other parts and tools.

These bushings work in both countersunk and standard drill holes. To install, place the bushing inside the hole in your jig. A chamfered edge on the bottom of the bushing helps center the bushing in the hole. Once centered, press the bushing into the hole with a hydraulic or lever press.

For technical drawings and 3-D models, click on a part number.

		Head		Tolerance								Each
OD, mm	Lg., mm	OD, mm	Thick., mm	ID, mm	OD, mm	Lg., mm	Drill Bushing Type	Material	Hardness	Specifications Met		1-5	6-11	12-Up
6.1 mm ID
12	7	15	3	0.013 to 0.028	0.012 to 0.023	-0.2 to 0.2	H	Steel	Rockwell C61	DIN 172	000000000	000000	000000	00000
12	13	15	3	0.013 to 0.028	0.012 to 0.023	-0.2 to 0.2	H	Steel	Rockwell C61	DIN 172	000000000	00000	00000	00000
12	17	15	3	0.013 to 0.028	0.012 to 0.023	-0.2 to 0.2	H	Steel	Rockwell C61	DIN 172	000000000	00000	00000	00000

Email Us

About Plain Bearings

Water-Resistant Dry-Running Sleeve Bearings

Metric Press-Fit Drill Bushings

Metric Press-Fit Drill Bushings with Head