Filter by
DFARS Compliance
Bearing Type
For Load Direction
About Plain Bearings
More
Selecting Compatible Lead Screws and Nuts
More
Oil-Embedded Sleeve Bearings
Startup friction causes these porous bronze bearings to release a thin layer of oil on the bearing’s surface. They are also known as Oilite® bearings.
Note: Dynamic load capacity is the maximum load a bearing can withstand at a given shaft speed. If your application’s load and speed requirements are below the values listed, the bearing will work.
For technical drawings and 3-D models, click on a part number.
841 Bronze Bearings
| For Housing ID | Lg. | Dynamic Radial Load Capacity | Lubrication | Lubricant | Temperature Range, °F | Each | |
For 5/16" Shaft Dia. | |||||||
|---|---|---|---|---|---|---|---|
| 7/16" | 1 3/8" | 850 lbs. @ 120 rpm | Lubricated | SAE 30 Oil | -35° to 300° | 00000000 | 00000 |
For 1/2" Shaft Dia. | |||||||
| 11/16" | 1 3/8" | 1,350 lbs. @ 120 rpm | Lubricated | SAE 30 Oil | 10° to 175° | 00000000 | 0000 |
For 9/16" Shaft Dia. | |||||||
| 3/4" | 1 3/8" | 1,500 lbs. @ 60 rpm | Lubricated | SAE 30 Oil | -35° to 300° | 00000000 | 0000 |
| 7/8" | 1 3/8" | 1,500 lbs. @ 60 rpm | Lubricated | SAE 30 Oil | 10° to 175° | 00000000 | 0000 |
For 5/8" Shaft Dia. | |||||||
| 13/16" | 1 3/8" | 1,700 lbs. @ 60 rpm | Lubricated | SAE 30 Oil | 10° to 175° | 0000000 | 0000 |
| 7/8" | 1 3/8" | 1,700 lbs. @ 60 rpm | Lubricated | SAE 30 Oil | -35° to 300° | 00000000 | 0000 |
For 3/4" Shaft Dia. | |||||||
| 7/8" | 1 3/8" | 2,050 lbs. @ 60 rpm | Lubricated | SAE 30 Oil | -35° to 300° | 00000000 | 0000 |
| 1" | 1 3/8" | 2,050 lbs. @ 60 rpm | Lubricated | SAE 30 Oil | -35° to 300° | 00000000 | 00000 |
For 7/8" Shaft Dia. | |||||||
| 1 1/8" | 1 3/8" | 2,400 lbs. @ 60 rpm | Lubricated | SAE 30 Oil | -35° to 300° | 00000000 | 0000 |
| 1 1/4" | 1 3/8" | 2,400 lbs. @ 60 rpm | Lubricated | SAE 30 Oil | 10° to 175° | 0000000 | 00000 |
For 1" Shaft Dia. | |||||||
| 1 1/8" | 1 3/8" | 2,750 lbs. @ 60 rpm | Lubricated | SAE 30 Oil | 10° to 175° | 00000000 | 0000 |
| 1 3/8" | 1 3/8" | 2,750 lbs. @ 60 rpm | Lubricated | SAE 30 Oil | 10° to 175° | 0000000 | 0000 |
For 1 1/4" Shaft Dia. | |||||||
| 1 1/2" | 1 3/8" | 3,400 lbs. @ 30 rpm | Lubricated | SAE 30 Oil | -35° to 300° | 00000000 | 0000 |
For 1 1/2" Shaft Dia. | |||||||
| 1 3/4" | 1 3/8" | 4,100 lbs. @ 30 rpm | Lubricated | SAE 30 Oil | -35° to 300° | 00000000 | 00000 |
High-Load Oil-Embedded Sleeve Bearings
Increased iron content makes these bearings stronger and more resistant to shock loads than standard oil-embedded bearings; however they operate at lower speeds. Startup friction causes them to release a thin layer of oil on the bearing’s surface. Color is silver because of the iron. These bearings are also magnetic due to the high iron content.
863 iron-copper bearings are also known as Super Oilite® bearings.
Note: Dynamic load capacity is the maximum load a bearing can withstand at a given shaft speed. If your application’s load and speed requirements are below the values listed, the bearing will work.
For technical drawings and 3-D models, click on a part number.
863 Iron-Copper Bearings
| For Housing ID | Lg. | Dynamic Radial Load Capacity | Lubrication | Lubricant | Temperature Range, °F | Each | |
For 9/16" Shaft Dia. | |||||||
|---|---|---|---|---|---|---|---|
| 3/4" | 1 3/8" | 3,050 lbs. @ 60 rpm | Lubricated | SAE 90 Oil | -15° to 300° | 00000000 | 00000 |
High-Temperature Dry-Running Sleeve Bearings
Graphite provides a layer of dry lubrication that operates in high-temperature environments.
Graphalloy bearings perform at extreme temperatures and under water. They are electrically conductive and wear resistant.
Note: Dynamic load capacity is the maximum load a bearing can withstand at a given shaft speed. If your application’s load and speed requirements are below the values listed, the bearing will work.
For technical drawings and 3-D models, click on a part number.
Embedded
| For Housing ID | Lg. | Dynamic Radial Load Capacity | Lubrication Method | Temperature Range, °F | Each | |
Graphalloy | ||||||
|---|---|---|---|---|---|---|
For 7/8" Shaft Dia. | ||||||
| 1 1/4" | 1 3/8" | 900 lbs. @ 60 rpm | Embedded | -450° to 750° | 0000000 | 000000 |
Press-Fit Drill Bushings
Mount flush with jig plates for precise drilling. These bushings can also be used as spacers, shims, and machinery bushings.
Don't see the size you need? Additional sizes are available.
For technical drawings and 3-D models, click on a part number.
Tolerance | Each | |||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|
| OD | Lg. | For Drill Bit Size | ID | OD | Lg. | Drill Bushing Type | Material | Hardness | 1-5 | 6-11 | 12-Up | |
0.0625" ID | ||||||||||||
| 13/64" | 1 3/8" | 1/16" | 0.0001" to 0.0004" | 0.0012" to 0.0015" | -0.01" to 0.01" | P | Steel | Rockwell C61 | 000000000 | 000000 | 000000 | 00000 |
0.073" ID | ||||||||||||
| 13/64" | 1 3/8" | No. 49 | 0.0001" to 0.0004" | 0.0012" to 0.0015" | -0.01" to 0.01" | P | Steel | Rockwell C61 | 000000000 | 00000 | 00000 | 0000 |
0.089" ID | ||||||||||||
| 13/64" | 1 3/8" | No. 43 | 0.0001" to 0.0004" | 0.0012" to 0.0015" | -0.01" to 0.01" | P | Steel | Rockwell C61 | 000000000 | 00000 | 00000 | 0000 |
0.0935" ID | ||||||||||||
| 13/64" | 1 3/8" | No. 42 | 0.0001" to 0.0004" | 0.0012" to 0.0015" | -0.01" to 0.01" | P | Steel | Rockwell C61 | 000000000 | 00000 | 00000 | 0000 |
0.0938" ID | ||||||||||||
| 13/64" | 1 3/8" | 3/32" | 0.0001" to 0.0004" | 0.0012" to 0.0015" | -0.01" to 0.01" | P | Steel | Rockwell C61 | 000000000 | 00000 | 00000 | 0000 |
0.096" ID | ||||||||||||
| 13/64" | 1 3/8" | No. 41 | 0.0001" to 0.0004" | 0.0012" to 0.0015" | -0.01" to 0.01" | P | Steel | Rockwell C61 | 000000000 | 00000 | 00000 | 0000 |
0.098" ID | ||||||||||||
| 1/4" | 1 3/8" | No. 40 | 0.0001" to 0.0004" | 0.0013" to 0.0016" | -0.01" to 0.01" | P | Steel | Rockwell C61 | 000000000 | 00000 | 0000 | 0000 |
0.0995" ID | ||||||||||||
| 1/4" | 1 3/8" | No. 39 | 0.0001" to 0.0004" | 0.0013" to 0.0016" | -0.01" to 0.01" | P | Steel | Rockwell C61 | 000000000 | 00000 | 0000 | 0000 |
0.1065" ID | ||||||||||||
| 1/4" | 1 3/8" | No. 36 | 0.0001" to 0.0004" | 0.0013" to 0.0016" | -0.01" to 0.01" | P | Steel | Rockwell C61 | 000000000 | 00000 | 0000 | 0000 |
0.11" ID | ||||||||||||
| 1/4" | 1 3/8" | No. 35 | 0.0001" to 0.0004" | 0.0013" to 0.0016" | -0.01" to 0.01" | P | Steel | Rockwell C61 | 000000000 | 00000 | 0000 | 0000 |
0.12" ID | ||||||||||||
| 1/4" | 1 3/8" | No. 31 | 0.0001" to 0.0004" | 0.0013" to 0.0016" | -0.01" to 0.01" | P | Steel | Rockwell C61 | 000000000 | 00000 | 0000 | 0000 |
0.125" ID | ||||||||||||
| 1/4" | 1 3/8" | 1/8" | 0.0001" to 0.0004" | 0.0013" to 0.0016" | -0.01" to 0.01" | P | Steel | Rockwell C61 | 000000000 | 00000 | 0000 | 0000 |
| 5/16" | 1 3/8" | 1/8" | 0.0001" to 0.0004" | 0.0013" to 0.0016" | -0.01" to 0.01" | P | Steel | Rockwell C61 | 000000000 | 00000 | 00000 | 0000 |
Tolerance | Each | |||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|
| OD | Lg. | For Drill Bit Size | ID | OD | Lg. | Drill Bushing Type | Material | Hardness | 1-5 | 6-11 | 12-Up | |
0.1285" ID | ||||||||||||
| 1/4" | 1 3/8" | No. 30 | 0.0001" to 0.0004" | 0.0013" to 0.0016" | -0.01" to 0.01" | P | Steel | Rockwell C61 | 000000000 | 000000 | 00000 | 00000 |
| 5/16" | 1 3/8" | No. 30 | 0.0001" to 0.0004" | 0.0013" to 0.0016" | -0.01" to 0.01" | P | Steel | Rockwell C61 | 000000000 | 00000 | 00000 | 0000 |
0.136" ID | ||||||||||||
| 1/4" | 1 3/8" | No. 29 | 0.0001" to 0.0004" | 0.0013" to 0.0016" | -0.01" to 0.01" | P | Steel | Rockwell C61 | 000000000 | 00000 | 0000 | 0000 |
0.1406" ID | ||||||||||||
| 5/16" | 1 3/8" | 9/64" | 0.0001" to 0.0004" | 0.0013" to 0.0016" | -0.01" to 0.01" | P | Steel | Rockwell C61 | 000000000 | 00000 | 00000 | 0000 |
0.1495" ID | ||||||||||||
| 5/16" | 1 3/8" | No. 25 | 0.0001" to 0.0004" | 0.0013" to 0.0016" | -0.01" to 0.01" | P | Steel | Rockwell C61 | 000000000 | 00000 | 00000 | 0000 |
0.1563" ID | ||||||||||||
| 5/16" | 1 3/8" | 5/32" | 0.0001" to 0.0004" | 0.0013" to 0.0016" | -0.01" to 0.01" | P | Steel | Rockwell C61 | 000000000 | 00000 | 00000 | 0000 |
0.157" ID | ||||||||||||
| 5/16" | 1 3/8" | No. 22 | 0.0001" to 0.0004" | 0.0013" to 0.0016" | -0.01" to 0.01" | P | Steel | Rockwell C61 | 000000000 | 00000 | 00000 | 0000 |
0.159" ID | ||||||||||||
| 5/16" | 1 3/8" | No. 21 | 0.0001" to 0.0004" | 0.0013" to 0.0016" | -0.01" to 0.01" | P | Steel | Rockwell C61 | 000000000 | 00000 | 00000 | 0000 |
0.161" ID | ||||||||||||
| 5/16" | 1 3/8" | No. 20 | 0.0001" to 0.0004" | 0.0013" to 0.0016" | -0.01" to 0.01" | P | Steel | Rockwell C61 | 000000000 | 00000 | 00000 | 0000 |
0.166" ID | ||||||||||||
| 5/16" | 1 3/8" | No. 19 | 0.0001" to 0.0004" | 0.0013" to 0.0016" | -0.01" to 0.01" | P | Steel | Rockwell C61 | 000000000 | 00000 | 00000 | 0000 |
0.1719" ID | ||||||||||||
| 5/16" | 1 3/8" | 11/64" | 0.0001" to 0.0004" | 0.0013" to 0.0016" | -0.01" to 0.01" | P | Steel | Rockwell C61 | 000000000 | 00000 | 00000 | 0000 |
0.18" ID | ||||||||||||
| 5/16" | 1 3/8" | No. 15 | 0.0001" to 0.0004" | 0.0013" to 0.0016" | -0.01" to 0.01" | P | Steel | Rockwell C61 | 000000000 | 00000 | 00000 | 0000 |
0.1875" ID | ||||||||||||
| 5/16" | 1 3/8" | 3/16" | 0.0001" to 0.0004" | 0.0013" to 0.0016" | -0.015" to 0.015" | P | Steel | Rockwell C61 | 00000000 | 00000 | 00000 | 00000 |
| 1/2" | 1 3/8" | 3/16" | 0.0001" to 0.0004" | 0.0014" to 0.0017" | -0.01" to 0.01" | P | Steel | Rockwell C61 | 000000000 | 00000 | 0000 | 0000 |
0.189" ID | ||||||||||||
| 5/16" | 1 3/8" | No. 12 | 0.0001" to 0.0004" | 0.0013" to 0.0016" | -0.01" to 0.01" | P | Steel | Rockwell C61 | 000000000 | 00000 | 00000 | 0000 |
| 1/2" | 1 3/8" | No. 12 | 0.0001" to 0.0004" | 0.0014" to 0.0017" | -0.01" to 0.01" | P | Steel | Rockwell C61 | 000000000 | 00000 | 0000 | 0000 |
Tolerance | Each | |||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|
| OD | Lg. | For Drill Bit Size | ID | OD | Lg. | Drill Bushing Type | Material | Hardness | 1-5 | 6-11 | 12-Up | |
0.191" ID | ||||||||||||
| 5/16" | 1 3/8" | No. 11 | 0.0001" to 0.0004" | 0.0013" to 0.0016" | -0.01" to 0.01" | P | Steel | Rockwell C61 | 000000000 | 000000 | 000000 | 00000 |
0.1935" ID | ||||||||||||
| 5/16" | 1 3/8" | No. 10 | 0.0001" to 0.0004" | 0.0013" to 0.0016" | -0.01" to 0.01" | P | Steel | Rockwell C61 | 000000000 | 00000 | 00000 | 0000 |
0.2031" ID | ||||||||||||
| 1/2" | 1 3/8" | 13/64" | 0.0001" to 0.0004" | 0.0014" to 0.0017" | -0.01" to 0.01" | P | Steel | Rockwell C61 | 000000000 | 00000 | 0000 | 0000 |
0.2188" ID | ||||||||||||
| 1/2" | 1 3/8" | 7/32" | 0.0001" to 0.0004" | 0.0014" to 0.0017" | -0.01" to 0.01" | P | Steel | Rockwell C61 | 000000000 | 00000 | 0000 | 0000 |
0.221" ID | ||||||||||||
| 1/2" | 1 3/8" | No. 2 | 0.0001" to 0.0004" | 0.0014" to 0.0017" | -0.01" to 0.01" | P | Steel | Rockwell C61 | 000000000 | 00000 | 0000 | 0000 |
0.25" ID | ||||||||||||
| 13/32" | 1 3/8" | 1/4", E | 0.0001" to 0.0004" | 0.0012" to 0.0016" | -0.01" to 0.01" | P | Steel | Rockwell C61 | 000000000 | 00000 | 0000 | 0000 |
| 1/2" | 1 3/8" | 1/4", E | 0.0001" to 0.0004" | 0.0014" to 0.0017" | -0.015" to 0.015" | P | Steel | Rockwell C61 | 00000000 | 00000 | 00000 | 0000 |
Tolerance | Each | |||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|
| OD | Lg. | For Drill Bit Size | ID | OD | Lg. | Drill Bushing Type | Material | Hardness | 1-5 | 6-11 | 12-Up | |
0.257" ID | ||||||||||||
| 1/2" | 1 3/8" | F | 0.0001" to 0.0005" | 0.0014" to 0.0017" | -0.01" to 0.01" | P | Steel | Rockwell C61 | 000000000 | 000000 | 00000 | 00000 |
0.2656" ID | ||||||||||||
| 1/2" | 1 3/8" | 17/64" | 0.0001" to 0.0005" | 0.0014" to 0.0017" | -0.01" to 0.01" | P | Steel | Rockwell C61 | 000000000 | 00000 | 0000 | 0000 |
0.266" ID | ||||||||||||
| 1/2" | 1 3/8" | H | 0.0001" to 0.0005" | 0.0014" to 0.0017" | -0.01" to 0.01" | P | Steel | Rockwell C61 | 000000000 | 00000 | 0000 | 0000 |
0.272" ID | ||||||||||||
| 1/2" | 1 3/8" | I | 0.0001" to 0.0005" | 0.0014" to 0.0017" | -0.01" to 0.01" | P | Steel | Rockwell C61 | 000000000 | 00000 | 0000 | 0000 |
0.2812" ID | ||||||||||||
| 1/2" | 1 3/8" | 9/32" | 0.0001" to 0.0005" | 0.0014" to 0.0017" | -0.01" to 0.01" | P | Steel | Rockwell C61 | 000000000 | 00000 | 0000 | 0000 |
0.29" ID | ||||||||||||
| 1/2" | 1 3/8" | L | 0.0001" to 0.0005" | 0.0014" to 0.0017" | -0.01" to 0.01" | P | Steel | Rockwell C61 | 000000000 | 00000 | 0000 | 0000 |
0.2969" ID | ||||||||||||
| 1/2" | 1 3/8" | 19/64" | 0.0001" to 0.0005" | 0.0014" to 0.0017" | -0.01" to 0.01" | P | Steel | Rockwell C61 | 000000000 | 00000 | 0000 | 0000 |
0.3125" ID | ||||||||||||
| 1/2" | 1 3/8" | 5/16" | 0.0001" to 0.0005" | 0.0014" to 0.0017" | -0.01" to 0.01" | P | Steel | Rockwell C61 | 000000000 | 00000 | 0000 | 0000 |
| 5/8" | 1 3/8" | 5/16" | 0.0001" to 0.0005" | 0.0014" to 0.0017" | -0.015" to 0.015" | P | Steel | Rockwell C61 | 00000000 | 00000 | 00000 | 00000 |
0.316" ID | ||||||||||||
| 1/2" | 1 3/8" | O | 0.0001" to 0.0005" | 0.0014" to 0.0017" | -0.01" to 0.01" | P | Steel | Rockwell C61 | 000000000 | 00000 | 0000 | 0000 |
| 5/8" | 1 3/8" | O | 0.0001" to 0.0005" | 0.0014" to 0.0017" | -0.01" to 0.01" | P | Steel | Rockwell C61 | 000000000 | 00000 | 0000 | 0000 |
0.3281" ID | ||||||||||||
| 5/8" | 1 3/8" | 21/64" | 0.0001" to 0.0005" | 0.0014" to 0.0017" | -0.015" to 0.015" | P | Steel | Rockwell C61 | 00000000 | 00000 | 00000 | 00000 |
Tolerance | Each | |||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|
| OD | Lg. | For Drill Bit Size | ID | OD | Lg. | Drill Bushing Type | Material | Hardness | 1-5 | 6-11 | 12-Up | |
0.3438" ID | ||||||||||||
| 5/8" | 1 3/8" | 11/32" | 0.0001" to 0.0005" | 0.0014" to 0.0017" | -0.015" to 0.015" | P | Steel | Rockwell C61 | 00000000 | 000000 | 000000 | 000000 |
0.375" ID | ||||||||||||
| 5/8" | 1 3/8" | 3/8" | 0.0001" to 0.0005" | 0.0014" to 0.0017" | -0.015" to 0.015" | P | Steel | Rockwell C61 | 00000000 | 00000 | 00000 | 00000 |
| 3/4" | 1 3/8" | 3/8" | 0.0001" to 0.0005" | 0.0015" to 0.0018" | -0.015" to 0.015" | P | Steel | Rockwell C61 | 00000000 | 00000 | 00000 | 00000 |
0.377" ID | ||||||||||||
| 5/8" | 1 3/8" | V | 0.0001" to 0.0005" | 0.0014" to 0.0017" | -0.01" to 0.01" | P | Steel | Rockwell C61 | 000000000 | 00000 | 0000 | 0000 |
| 3/4" | 1 3/8" | V | 0.0001" to 0.0005" | 0.0015" to 0.0018" | -0.01" to 0.01" | P | Steel | Rockwell C61 | 000000000 | 00000 | 0000 | 0000 |
0.3906" ID | ||||||||||||
| 5/8" | 1 3/8" | 25/64" | 0.0001" to 0.0005" | 0.0014" to 0.0017" | -0.015" to 0.015" | P | Steel | Rockwell C61 | 00000000 | 00000 | 00000 | 00000 |
0.4063" ID | ||||||||||||
| 5/8" | 1 3/8" | 13/32" | 0.0001" to 0.0005" | 0.0014" to 0.0017" | -0.015" to 0.015" | P | Steel | Rockwell C61 | 00000000 | 00000 | 00000 | 00000 |
0.4219" ID | ||||||||||||
| 5/8" | 1 3/8" | 27/64" | 0.0001" to 0.0005" | 0.0014" to 0.0017" | -0.015" to 0.015" | P | Steel | Rockwell C61 | 00000000 | 00000 | 00000 | 00000 |
| 3/4" | 1 3/8" | 27/64" | 0.0001" to 0.0005" | 0.0015" to 0.0018" | -0.01" to 0.01" | P | Steel | Rockwell C61 | 000000000 | 00000 | 0000 | 0000 |
0.4375" ID | ||||||||||||
| 5/8" | 1 3/8" | 7/16" | 0.0001" to 0.0005" | 0.0014" to 0.0017" | -0.015" to 0.015" | P | Steel | Rockwell C61 | 00000000 | 00000 | 00000 | 00000 |
| 3/4" | 1 3/8" | 7/16" | 0.0001" to 0.0005" | 0.0015" to 0.0018" | -0.015" to 0.015" | P | Steel | Rockwell C61 | 00000000 | 00000 | 00000 | 00000 |
0.4844" ID | ||||||||||||
| 3/4" | 1 3/8" | 31/64" | 0.0001" to 0.0005" | 0.0015" to 0.0018" | -0.01" to 0.01" | P | Steel | Rockwell C61 | 000000000 | 00000 | 0000 | 0000 |
Tolerance | Each | |||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|
| OD | Lg. | For Drill Bit Size | ID | OD | Lg. | Drill Bushing Type | Material | Hardness | 1-5 | 6-11 | 12-Up | |
0.5" ID | ||||||||||||
| 3/4" | 1 3/8" | 1/2" | 0.0001" to 0.0005" | 0.0015" to 0.0018" | -0.015" to 0.015" | P | Steel | Rockwell C61 | 00000000 | 000000 | 000000 | 000000 |
| 7/8" | 1 3/8" | 1/2" | 0.0001" to 0.0005" | 0.0015" to 0.0018" | -0.01" to 0.01" | P | Steel | Rockwell C61 | 000000000 | 00000 | 0000 | 0000 |
| 1" | 1 3/8" | 1/2" | 0.0001" to 0.0005" | 0.0015" to 0.0018" | -0.01" to 0.01" | P | Steel | Rockwell C61 | 000000000 | 00000 | 00000 | 0000 |
0.5156" ID | ||||||||||||
| 3/4" | 1 3/8" | 33/64" | 0.0001" to 0.0005" | 0.0015" to 0.0018" | -0.01" to 0.01" | P | Steel | Rockwell C61 | 000000000 | 00000 | 0000 | 0000 |
| 7/8" | 1 3/8" | 33/64" | 0.0001" to 0.0005" | 0.0015" to 0.0018" | -0.01" to 0.01" | P | Steel | Rockwell C61 | 000000000 | 00000 | 0000 | 0000 |
0.5312" ID | ||||||||||||
| 1" | 1 3/8" | 17/32" | 0.0001" to 0.0005" | 0.0015" to 0.0018" | -0.01" to 0.01" | P | Steel | Rockwell C61 | 000000000 | 00000 | 00000 | 0000 |
0.5313" ID | ||||||||||||
| 3/4" | 1 3/8" | 17/32" | 0.0001" to 0.0005" | 0.0015" to 0.0018" | -0.015" to 0.015" | P | Steel | Rockwell C61 | 00000000 | 00000 | 00000 | 00000 |
0.5625" ID | ||||||||||||
| 7/8" | 1 3/8" | 9/16" | 0.0001" to 0.0005" | 0.0015" to 0.0018" | -0.01" to 0.01" | P | Steel | Rockwell C61 | 000000000 | 00000 | 0000 | 0000 |
| 1" | 1 3/8" | 9/16" | 0.0001" to 0.0005" | 0.0015" to 0.0018" | -0.01" to 0.01" | P | Steel | Rockwell C61 | 000000000 | 00000 | 00000 | 0000 |
0.625" ID | ||||||||||||
| 7/8" | 1 3/8" | 5/8" | 0.0001" to 0.0005" | 0.0015" to 0.0018" | -0.015" to 0.015" | P | Steel | Rockwell C61 | 00000000 | 00000 | 00000 | 00000 |
| 1" | 1 3/8" | 5/8" | 0.0001" to 0.0005" | 0.0015" to 0.0018" | -0.015" to 0.015" | P | Steel | Rockwell C61 | 00000000 | 00000 | 00000 | 00000 |
| 1 1/8" | 1 3/8" | 5/8" | 0.0001" to 0.0005" | 0.0017" to 0.002" | -0.015" to 0.015" | P | Steel | Rockwell C61 | 00000000 | 00000 | 00000 | 00000 |
| 1 3/8" | 1 3/8" | 5/8" | 0.0001" to 0.0005" | 0.0018" to 0.0022" | -0.015" to 0.015" | P | Steel | Rockwell C61 | 00000000 | 00000 | 00000 | 00000 |
Tolerance | Each | |||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|
| OD | Lg. | For Drill Bit Size | ID | OD | Lg. | Drill Bushing Type | Material | Hardness | 1-5 | 6-11 | 12-Up | |
0.7031" ID | ||||||||||||
| 1" | 1 3/8" | 45/64" | 0.0001" to 0.0005" | 0.0015" to 0.0018" | -0.01" to 0.01" | P | Steel | Rockwell C61 | 000000000 | 000000 | 000000 | 00000 |
0.75" ID | ||||||||||||
| 1" | 1 3/8" | 3/4" | 0.0001" to 0.0005" | 0.0015" to 0.0018" | -0.015" to 0.015" | P | Steel | Rockwell C61 | 00000000 | 00000 | 00000 | 00000 |
| 1 3/8" | 1 3/8" | 3/4" | 0.0001" to 0.0005" | 0.0018" to 0.0022" | -0.015" to 0.015" | P | Steel | Rockwell C61 | 00000000 | 00000 | 00000 | 00000 |
0.7656" ID | ||||||||||||
| 1" | 1 3/8" | 49/64" | 0.0002" to 0.0006" | 0.0015" to 0.0018" | -0.01" to 0.01" | P | Steel | Rockwell C61 | 000000000 | 00000 | 00000 | 0000 |
0.8125" ID | ||||||||||||
| 1 3/8" | 1 3/8" | 13/16" | 0.0002" to 0.0006" | 0.0018" to 0.0022" | -0.01" to 0.01" | P | Steel | Rockwell C61 | 000000000 | 00000 | 00000 | 00000 |
0.875" ID | ||||||||||||
| 1 3/8" | 1 3/8" | 7/8" | 0.0002" to 0.0006" | 0.0018" to 0.0022" | -0.015" to 0.015" | P | Steel | Rockwell C61 | 00000000 | 00000 | 00000 | 00000 |
0.9688" ID | ||||||||||||
| 1 3/8" | 1 3/8" | 31/32" | 0.0002" to 0.0006" | 0.0018" to 0.0022" | -0.01" to 0.01" | P | Steel | Rockwell C61 | 000000000 | 00000 | 00000 | 00000 |
1" ID | ||||||||||||
| 1 3/8" | 1 3/8" | 1" | 0.0002" to 0.0006" | 0.0018" to 0.0022" | -0.015" to 0.015" | P | Steel | Rockwell C61 | 00000000 | 00000 | 00000 | 00000 |
| 1 3/4" | 1 3/8" | 1" | 0.0002" to 0.0006" | 0.0019" to 0.0023" | -0.015" to 0.015" | P | Steel | Rockwell C61 | 00000000 | 00000 | 00000 | 00000 |
1.0156" ID | ||||||||||||
| 1 3/4" | 1 3/8" | 1 1/64" | 0.0002" to 0.0006" | 0.0019" to 0.0023" | -0.015" to 0.015" | P | Steel | Rockwell C61 | 00000000 | 00000 | 00000 | 00000 |
Tolerance | Each | |||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|
| OD | Lg. | For Drill Bit Size | ID | OD | Lg. | Drill Bushing Type | Material | Hardness | 1-5 | 6-11 | 12-Up | |
1.0312" ID | ||||||||||||
| 1 3/8" | 1 3/8" | 1 1/32" | 0.0002" to 0.0006" | 0.0018" to 0.0022" | -0.01" to 0.01" | P | Steel | Rockwell C61 | 000000000 | 000000 | 000000 | 000000 |
1.0469" ID | ||||||||||||
| 1 3/4" | 1 3/8" | 1 3/64" | 0.0002" to 0.0006" | 0.0019" to 0.0023" | -0.015" to 0.015" | P | Steel | Rockwell C61 | 00000000 | 00000 | 00000 | 00000 |
1.0625" ID | ||||||||||||
| 1 3/4" | 1 3/8" | 1 1/16" | 0.0002" to 0.0006" | 0.0019" to 0.0023" | -0.015" to 0.015" | P | Steel | Rockwell C61 | 00000000 | 00000 | 00000 | 00000 |
1.125" ID | ||||||||||||
| 1 3/4" | 1 3/8" | 1 1/8" | 0.0002" to 0.0006" | 0.0019" to 0.0023" | -0.015" to 0.015" | P | Steel | Rockwell C61 | 00000000 | 00000 | 00000 | 00000 |
1.25" ID | ||||||||||||
| 1 5/8" | 1 3/8" | 1 1/4" | 0.0002" to 0.0006" | 0.0018" to 0.0022" | -0.015" to 0.015" | P | Steel | Rockwell C61 | 00000000 | 00000 | 00000 | 00000 |
| 1 3/4" | 1 3/8" | 1 1/4" | 0.0002" to 0.0006" | 0.0019" to 0.0023" | -0.015" to 0.015" | P | Steel | Rockwell C61 | 00000000 | 00000 | 00000 | 00000 |
1.2812" ID | ||||||||||||
| 1 3/4" | 1 3/8" | 1 9/32" | 0.0002" to 0.0006" | 0.0019" to 0.0023" | -0.01" to 0.01" | P | Steel | Rockwell C61 | 000000000 | 00000 | 00000 | 00000 |
1.375" ID | ||||||||||||
| 1 3/4" | 1 3/8" | 1 3/8" | 0.0002" to 0.0006" | 0.0019" to 0.0023" | -0.01" to 0.01" | P | Steel | Rockwell C61 | 000000000 | 00000 | 00000 | 00000 |
| 2 1/4" | 1 3/8" | 1 3/8" | 0.0002" to 0.0006" | 0.0021" to 0.0025" | -0.01" to 0.01" | P | Steel | Rockwell C61 | 000000000 | 00000 | 00000 | 00000 |
1.4375" ID | ||||||||||||
| 2 1/4" | 1 3/8" | 1 7/16" | 0.0002" to 0.0006" | 0.0021" to 0.0025" | -0.01" to 0.01" | P | Steel | Rockwell C61 | 000000000 | 00000 | 00000 | 00000 |
1.5" ID | ||||||||||||
| 2 1/4" | 1 3/8" | 1 1/2" | 0.0002" to 0.0006" | 0.0021" to 0.0025" | -0.01" to 0.01" | P | Steel | Rockwell C61 | 000000000 | 00000 | 00000 | 00000 |
1.5625" ID | ||||||||||||
| 2 1/4" | 1 3/8" | 1 9/16" | 0.0003" to 0.0007" | 0.0021" to 0.0025" | -0.01" to 0.01" | P | Steel | Rockwell C61 | 000000000 | 00000 | 00000 | 00000 |
1.75" ID | ||||||||||||
| 2 1/4" | 1 3/8" | 1 3/4" | 0.0003" to 0.0007" | 0.0021" to 0.0025" | -0.015" to 0.015" | P | Steel | Rockwell C61 | 00000000 | 00000 | 00000 | 00000 |
Press-Fit Drill Bushings with Head
The head prevents these bushings from being pushed through the jig when drilling pressure is extreme. The head sits above the jig plate or can be mounted flush by installing in a counterbored hole. Drill bushings can also be used as spacers, shims, and machinery bushings.
Don't see the size you need? Additional sizes are available.
For technical drawings and 3-D models, click on a part number.
Head | Tolerance | Each | ||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| OD | Lg. | For Drill Bit Size | OD | Thick. | ID | OD | Lg. | Drill Bushing Type | Material | Hardness | 1-5 | 6-11 | 12-Up | |
0.1875" ID | ||||||||||||||
| 5/16" | 1 3/8" | 3/16" | 27/64" | 1/8" | 0.0001" to 0.0004" | 0.0013" to 0.0016" | -0.015" to 0.015" | H | Steel | Rockwell C61 | 00000000 | 000000 | 000000 | 000000 |
| 13/32" | 1 3/8" | 3/16" | 1/2" | 5/32" | 0.0001" to 0.0004" | 0.0013" to 0.0016" | -0.015" to 0.015" | H | Steel | Rockwell C61 | 00000000 | 00000 | 00000 | 00000 |
| 1/2" | 1 3/8" | 3/16" | 39/64" | 7/32" | 0.0001" to 0.0004" | 0.0014" to 0.0017" | -0.015" to 0.015" | H | Steel | Rockwell C61 | 00000000 | 00000 | 00000 | 00000 |
Head | Tolerance | Each | ||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| OD | Lg. | For Drill Bit Size | OD | Thick. | ID | OD | Lg. | Drill Bushing Type | Material | Hardness | 1-5 | 6-11 | 12-Up | |
0.25" ID | ||||||||||||||
| 13/32" | 1 3/8" | 1/4", E | 1/2" | 5/32" | 0.0001" to 0.0004" | 0.0013" to 0.0016" | -0.015" to 0.015" | H | Steel | Rockwell C61 | 00000000 | 000000 | 000000 | 000000 |
| 1/2" | 1 3/8" | 1/4", E | 39/64" | 7/32" | 0.0001" to 0.0004" | 0.0014" to 0.0017" | -0.015" to 0.015" | H | Steel | Rockwell C61 | 00000000 | 00000 | 00000 | 00000 |
Head | Tolerance | Each | ||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| OD | Lg. | For Drill Bit Size | OD | Thick. | ID | OD | Lg. | Drill Bushing Type | Material | Hardness | 1-5 | 6-11 | 12-Up | |
0.3125" ID | ||||||||||||||
| 1/2" | 1 3/8" | 5/16" | 39/64" | 7/32" | 0.0001" to 0.0005" | 0.0014" to 0.0017" | -0.015" to 0.015" | H | Steel | Rockwell C61 | 00000000 | 000000 | 000000 | 000000 |
| 5/8" | 1 3/8" | 5/16" | 51/64" | 7/32" | 0.0001" to 0.0005" | 0.0014" to 0.0017" | -0.015" to 0.015" | H | Steel | Rockwell C61 | 00000000 | 00000 | 00000 | 00000 |
| 3/4" | 1 3/8" | 5/16" | 59/64" | 7/32" | 0.0001" to 0.0005" | 0.0015" to 0.0018" | -0.015" to 0.015" | H | Steel | Rockwell C61 | 00000000 | 00000 | 00000 | 00000 |
0.375" ID | ||||||||||||||
| 5/8" | 1 3/8" | 3/8" | 51/64" | 7/32" | 0.0001" to 0.0005" | 0.0014" to 0.0017" | -0.015" to 0.015" | H | Steel | Rockwell C61 | 00000000 | 00000 | 00000 | 00000 |
| 3/4" | 1 3/8" | 3/8" | 59/64" | 7/32" | 0.0001" to 0.0005" | 0.0015" to 0.0018" | -0.015" to 0.015" | H | Steel | Rockwell C61 | 00000000 | 00000 | 00000 | 00000 |
0.4375" ID | ||||||||||||||
| 5/8" | 1 3/8" | 7/16" | 51/64" | 7/32" | 0.0001" to 0.0005" | 0.0014" to 0.0017" | -0.015" to 0.015" | H | Steel | Rockwell C61 | 00000000 | 00000 | 00000 | 00000 |
0.4531" ID | ||||||||||||||
| 3/4" | 1 3/8" | 29/64" | 59/64" | 7/32" | 0.0001" to 0.0005" | 0.0015" to 0.0018" | -0.015" to 0.015" | H | Steel | Rockwell C61 | 00000000 | 00000 | 00000 | 00000 |
0.5" ID | ||||||||||||||
| 3/4" | 1 3/8" | 1/2" | 59/64" | 7/32" | 0.0001" to 0.0005" | 0.0015" to 0.0018" | -0.015" to 0.015" | H | Steel | Rockwell C61 | 00000000 | 00000 | 00000 | 00000 |
| 1" | 1 3/8" | 1/2" | 1 15/64" | 5/16" | 0.0001" to 0.0005" | 0.0015" to 0.0018" | -0.015" to 0.015" | H | Steel | Rockwell C61 | 00000000 | 00000 | 00000 | 00000 |
Head | Tolerance | Each | ||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| OD | Lg. | For Drill Bit Size | OD | Thick. | ID | OD | Lg. | Drill Bushing Type | Material | Hardness | 1-5 | 6-11 | 12-Up | |
0.625" ID | ||||||||||||||
| 7/8" | 1 3/8" | 5/8" | 1 7/64" | 1/4" | 0.0001" to 0.0005" | 0.0015" to 0.0018" | -0.015" to 0.015" | H | Steel | Rockwell C61 | 00000000 | 000000 | 000000 | 000000 |
| 1" | 1 3/8" | 5/8" | 1 15/64" | 5/16" | 0.0001" to 0.0005" | 0.0015" to 0.0018" | -0.015" to 0.015" | H | Steel | Rockwell C61 | 00000000 | 00000 | 00000 | 00000 |
0.75" ID | ||||||||||||||
| 1" | 1 3/8" | 3/4" | 1 15/64" | 5/16" | 0.0001" to 0.0005" | 0.0015" to 0.0018" | -0.015" to 0.015" | H | Steel | Rockwell C61 | 00000000 | 00000 | 00000 | 00000 |
0.875" ID | ||||||||||||||
| 1 1/4" | 1 3/8" | 7/8" | 1 1/2" | 1/4" | 0.0002" to 0.0006" | 0.0017" to 0.002" | -0.01" to 0.01" | H | Steel | Rockwell C61 | 00000000 | 00000 | 00000 | 00000 |
1" ID | ||||||||||||||
| 1 3/8" | 1 3/8" | 1" | 1 39/64" | 3/8" | 0.0002" to 0.0006" | 0.0018" to 0.0022" | -0.015" to 0.015" | H | Steel | Rockwell C61 | 0000000 | 00000 | 00000 | 00000 |
| 1 3/4" | 1 3/8" | 1" | 1 63/64" | 3/8" | 0.0002" to 0.0006" | 0.0019" to 0.0023" | -0.015" to 0.015" | H | Steel | Rockwell C61 | 00000000 | 00000 | 00000 | 00000 |
1.0625" ID | ||||||||||||||
| 1 3/4" | 1 3/8" | 1 1/16" | 1 63/64" | 3/8" | 0.0002" to 0.0006" | 0.0019" to 0.0023" | -0.015" to 0.015" | H | Steel | Rockwell C61 | 00000000 | 00000 | 00000 | 00000 |
Head | Tolerance | Each | ||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| OD | Lg. | For Drill Bit Size | OD | Thick. | ID | OD | Lg. | Drill Bushing Type | Material | Hardness | 1-5 | 6-11 | 12-Up | |
1.125" ID | ||||||||||||||
| 1 3/4" | 1 3/8" | 1 1/8" | 1 63/64" | 3/8" | 0.0002" to 0.0006" | 0.0019" to 0.0023" | -0.015" to 0.015" | H | Steel | Rockwell C61 | 00000000 | 000000 | 000000 | 000000 |
1.25" ID | ||||||||||||||
| 1 3/4" | 1 3/8" | 1 1/4" | 1 63/64" | 3/8" | 0.0002" to 0.0006" | 0.0019" to 0.0023" | -0.015" to 0.015" | H | Steel | Rockwell C61 | 00000000 | 00000 | 00000 | 00000 |
1.3125" ID | ||||||||||||||
| 1 3/4" | 1 3/8" | 1 5/16" | 1 63/64" | 3/8" | 0.0002" to 0.0006" | 0.0019" to 0.0023" | -0.015" to 0.015" | H | Steel | Rockwell C61 | 00000000 | 00000 | 00000 | 00000 |
1.375" ID | ||||||||||||||
| 1 3/4" | 1 3/8" | 1 3/8" | 1 63/64" | 3/8" | 0.0002" to 0.0006" | 0.0019" to 0.0023" | -0.015" to 0.015" | H | Steel | Rockwell C61 | 00000000 | 00000 | 00000 | 00000 |
1.625" ID | ||||||||||||||
| 2 1/4" | 1 3/8" | 1 5/8" | 2 31/64" | 3/8" | 0.0003" to 0.0007" | 0.0021" to 0.0025" | -0.015" to 0.015" | H | Steel | Rockwell C61 | 00000000 | 00000 | 00000 | 00000 |
1.7656" ID | ||||||||||||||
| 2 1/4" | 1 3/8" | 1 49/64 | 2 31/64" | 3/8" | 0.0003" to 0.0007" | 0.0021" to 0.0025" | -0.015" to 0.015" | H | Steel | Rockwell C61 | 00000000 | 00000 | 00000 | 00000 |
Removable Drill Bushings
Replace worn bushings and quickly change IDs without needing to repeatedly use a lever press. Instead of pressing bushings in and out of your jig fixture, which can cause damage, these bushings slide in and out of sleeves (sold separately). By swapping in a bushing with a different ID, you can change the size of your bit and still use the same hole in your fixture. All are made to tight dimensional tolerances for consistent, accurate results, even as you change them in and out. They're also known as slip-fixed and renewable bushings.
Choose a sleeve with a length that matches the length of your bushing. To prevent bushings from spinning inside the sleeve as you drill, pair a standard sleeve with a lock screw, or use a locking sleeve.
Lock screws thread into a hole in your jig. The head of the screw fits into a notch on the bushing's head, which keeps the bushing from spinning.
For additional sizes, see Made-to-Order Removable Drill Bushings.
For technical drawings and 3-D models, click on a part number.
Bushings
Head | Tolerance | Each | ||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| OD | Lg. | For Drill Bit Size | OD | Thick. | Lock Screw/Bushing Ctr.-to-Ctr. | ID | OD | Lg. | Drill Bushing Type | Material | 1-5 | 6-11 | 12-Up | |
0.125" ID | ||||||||||||||
| 5/16" | 1 3/8" | 1/8" | 35/64" | 1/4" | 1/2" | 0.0001" to 0.0004" | -0.0002" to 0" | -0.015" to 0.015" | SF | Steel | 00000000 | 000000 | 000000 | 000000 |
0.1875" ID | ||||||||||||||
| 1/2" | 1 3/8" | 3/16" | 51/64" | 1/4" | 5/8" | 0.0001" to 0.0004" | -0.0002" to 0" | -0.015" to 0.015" | SF | Steel | 00000000 | 00000 | 00000 | 00000 |
0.25" ID | ||||||||||||||
| 1/2" | 1 3/8" | 1/4", E | 51/64" | 1/4" | 5/8" | 0.0001" to 0.0004" | -0.0002" to 0" | -0.015" to 0.015" | SF | Steel | 00000000 | 00000 | 00000 | 00000 |
0.3125" ID | ||||||||||||||
| 1/2" | 1 3/8" | 5/16" | 51/64" | 1/4" | 5/8" | 0.0001" to 0.0005" | -0.0002" to 0" | -0.015" to 0.015" | SF | Steel | 00000000 | 00000 | 00000 | 00000 |
0.3438" ID | ||||||||||||||
| 3/4" | 1 3/8" | 11/32" | 1 3/64" | 1/4" | 3/4" | 0.0001" to 0.0005" | -0.0002" to 0" | -0.015" to 0.015" | SF | Steel | 00000000 | 00000 | 00000 | 00000 |
0.3594" ID | ||||||||||||||
| 3/4" | 1 3/8" | 23/64" | 1 3/64" | 1/4" | 3/4" | 0.0001" to 0.0005" | -0.0002" to 0" | -0.015" to 0.015" | SF | Steel | 00000000 | 00000 | 00000 | 00000 |
0.4375" ID | ||||||||||||||
| 3/4" | 1 3/8" | 7/16" | 1 3/64" | 1/4" | 3/4" | 0.0001" to 0.0005" | -0.0002" to 0" | -0.015" to 0.015" | SF | Steel | 00000000 | 00000 | 00000 | 00000 |
0.5" ID | ||||||||||||||
| 3/4" | 1 3/8" | 1/2" | 1 3/64" | 1/4" | 3/4" | 0.0001" to 0.0005" | -0.0002" to 0" | -0.015" to 0.015" | SF | Steel | 00000000 | 00000 | 00000 | 00000 |
| 1" | 1 3/8" | 1/2" | 1 27/64" | 3/8" | 59/64" | 0.0001" to 0.0005" | -0.0002" to 0" | -0.015" to 0.015" | SF | Steel | 00000000 | 00000 | 00000 | 00000 |
0.625" ID | ||||||||||||||
| 1" | 1 3/8" | 5/8" | 1 27/64" | 3/8" | 59/64" | 0.0001" to 0.0005" | -0.0002" to 0" | -0.015" to 0.015" | SF | Steel | 00000000 | 00000 | 00000 | 00000 |
0.75" ID | ||||||||||||||
| 1" | 1 3/8" | 3/4" | 1 27/64" | 3/8" | 59/64" | 0.0001" to 0.0005" | -0.0002" to 0" | -0.015" to 0.015" | SF | Steel | 00000000 | 00000 | 00000 | 00000 |
| 1 3/8" | 1 3/8" | 3/4" | 1 51/64" | 3/8" | 1 7/64" | 0.0001" to 0.0005" | -0.0003" to 0" | -0.015" to 0.015" | SF | Steel | 00000000 | 00000 | 00000 | 00000 |
1" ID | ||||||||||||||
| 1 3/8" | 1 3/8" | 1" | 1 51/64" | 3/8" | 1 7/64" | 0.0002" to 0.0006" | -0.0003" to 0" | -0.015" to 0.015" | SF | Steel | 00000000 | 00000 | 00000 | 00000 |
| 1 3/4" | 1 3/8" | 1" | 2 19/64" | 3/8" | 1 25/64" | 0.0002" to 0.0006" | -0.0003" to 0" | -0.015" to 0.015" | SF | Steel | 00000000 | 00000 | 00000 | 00000 |
1.0469" ID | ||||||||||||||
| 1 3/4" | 1 3/8" | 1 3/64" | 2 19/64" | 3/8" | 1 25/64" | 0.0002" to 0.0006" | -0.0003" to 0" | -0.015" to 0.015" | SF | Steel | 00000000 | 00000 | 00000 | 00000 |
1.0625" ID | ||||||||||||||
| 1 3/4" | 1 3/8" | 1 1/16" | 2 19/64" | 3/8" | 1 25/64" | 0.0002" to 0.0006" | -0.0003" to 0" | -0.015" to 0.015" | SF | Steel | 00000000 | 00000 | 00000 | 00000 |
1.125" ID | ||||||||||||||
| 1 3/4" | 1 3/8" | 1 1/8" | 2 19/64" | 3/8" | 1 25/64" | 0.0002" to 0.0006" | -0.0003" to 0" | -0.015" to 0.015" | SF | Steel | 00000000 | 00000 | 00000 | 00000 |
1.25" ID | ||||||||||||||
| 1 3/4" | 1 3/8" | 1 1/4" | 2 19/64" | 3/8" | 1 25/64" | 0.0002" to 0.0006" | -0.0003" to 0" | -0.015" to 0.015" | SF | Steel | 00000000 | 00000 | 00000 | 00000 |
1.3125" ID | ||||||||||||||
| 1 3/4" | 1 3/8" | 1 5/16" | 2 19/64" | 3/8" | 1 25/64" | 0.0002" to 0.0006" | -0.0003" to 0" | -0.015" to 0.015" | SF | Steel | 00000000 | 00000 | 00000 | 00000 |
1.375" ID | ||||||||||||||
| 1 3/4" | 1 3/8" | 1 3/8" | 2 19/64" | 3/8" | 1 25/64" | 0.0002" to 0.0006" | -0.0003" to 0" | -0.015" to 0.015" | SF | Steel | 00000000 | 00000 | 00000 | 00000 |
1.875" ID | ||||||||||||||
| 2 1/4" | 1 3/8" | 1 7/8" | 2 51/64" | 3/8" | 1 41/64" | 0.0003" to 0.0007" | -0.0004" to 0" | -0.015" to 0.015" | SF | Steel | 00000000 | 00000 | 00000 | 00000 |
Lock Screws
Slotted
Hex
Shoulder | ||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|
| For Bushing OD | Thread Size  | Head OD | O'all Lg. | Head-to-Shoulder Lg. | Lg. | Wd. | Hex Size | For Drill Bushing Type | Material | Pkg. Qty. | Pkg. | |
Slotted | ||||||||||||
| 5/16", 1/2", 3/4" | 5/16"-18 | 5/8" | 5/8" | 1/4" | 0.138" | 3/8" | __ | SF | Steel | 10 | 0000000 | 000000 |
| 1", 1 3/8" | 5/16"-18 | 5/8" | 7/8" | 3/8" | 0.2" | 3/8" | __ | SF | Steel | 10 | 0000000 | 00000 |
| 1 3/4", 2 1/4" | 3/8"-16 | 3/4" | 1" | 3/8" | 0.2" | 7/16" | __ | SF | Steel | 10 | 0000000 | 00000 |
Hex | ||||||||||||
| 5/16", 1/2", 3/4" | 5/16"-18 | 5/8" | 5/8" | 1/4" | 0.138" | 3/8" | 3/16" | SF | Steel | 10 | 0000000 | 00000 |
| 1", 1 3/8" | 5/16"-18 | 5/8" | 7/8" | 3/8" | 0.2" | 3/8" | 3/16" | SF | Steel | 10 | 0000000 | 00000 |
| 1 3/4", 2 1/4" | 3/8"-16 | 3/4" | 1" | 3/8" | 0.2" | 7/16" | 7/32" | SF | Steel | 10 | 0000000 | 00000 |
Sleeves
| For Bushing OD | ID | OD | Lg. | ID Tolerance | For Drill Bushing Type | Material | Hardness | Sleeve ANSI Number | Each | |
| 1/2" | 1/2" | 3/4" | 1 3/8" | 0.0002" to 0.0005" | SF | Steel | Rockwell C61 | L-48-22 | 00000000 | 000000 |
| 3/4" | 3/4" | 1" | 1 3/8" | 0.0003" to 0.0006" | SF | Steel | Rockwell C61 | L-64-22 | 00000000 | 00000 |
| 1" | 1" | 1 3/8" | 1 3/8" | 0.0004" to 0.0007" | SF | Steel | Rockwell C61 | L-88-22 | 00000000 | 00000 |
| 1 3/8" | 1 3/8" | 1 3/4" | 1 3/8" | 0.0006" to 0.001" | SF | Steel | Rockwell C61 | L-112-22 | 00000000 | 00000 |
Metric Fast-Travel Ultra-Precision Lead Screws and Nuts
Multiple thread channels (also known as thread starts) create faster linear travel than lead screws with a single thread start. Operating with less backlash (play) than Metric Precision Acme Lead Screws and Nuts, these lead screws and nuts provide increased nut life and more reliable movement in automated systems. To ensure compatibility, select components that have the same thread size, thread pitch, and number of thread starts.
Acetal nuts have good wear and corrosion resistance.
Travel distance per turn, also known as screw lead, is the distance a nut moves with one revolution of the lead screw.
For technical drawings and 3-D models, click on a part number.
Flange Nuts—Right-Hand Threaded
F
Flange | ||||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| Thread Size | Thread Pitch, mm | Lg. | Dia. | Dia. | Thick. | No. of Thread Starts | Thread Type | Speed Ratio | Travel Distance per Turn, mm | Bolt Circle Dia. | Dynamic Thrust Load Cap., lbs. | Each | ||
Acetal Plastic | ||||||||||||||
| F | M12 | 2.5 | 1 3/8" | 1.102" | 1 57/64" | 15/32" | 2 | Metric Rounded Trapezoidal | 2:1 | 5 | 1 1/2" | Not Rated | 0000000 | 000000 |
| F | M16 | 5 | 1 3/8" | 1.102" | 1 57/64" | 15/32" | 7 | Metric Rounded Trapezoidal | 7:1 | 35 | 1 1/2" | Not Rated | 0000000 | 00000 |
Wheel Bearings
Replace worn or damaged wheel bearings to keep your equipment rolling. Use flanged bearings and ball bearings in pairs. Change the axle diameter with wheel reducer bushings (sold separately).
Note: Not for use in towing applications.
For impact-resistant tapered roller bearings, as well as other bearing materials and sizes, please see Ball and Roller Bearings and Sleeve Bearings. Roller bearings provide smooth rolling.
Retaining washers hold roller bearings in place.
For technical drawings and 3-D models, click on a part number.
Steel
Roller Bearing
| For Axle Dia. | OD | Lg. | Each | |
Roller Bearings | ||||
|---|---|---|---|---|
| 5/8" | 1 3/16" | 1 3/8" | 00000000 | 00000 |