Startup friction causes these porous bronze bearings to release a thin layer of oil on the bearing’s surface. Bearings are self-aligning to compensate for shaft misalignment.

Note: Dynamic load capacity is the maximum load a bearing can withstand at a given shaft speed. If your application’s load and speed requirements are below the values listed, the bearing will work.

For technical drawings and 3-D models, click on a part number.

Bearings are for use with round end-supported shafts. To install, slide bearings into a housing (not included). For bearings with retaining ring grooves, secure with two retaining rings (sold individually).

Bearings with end seals keep lubricant in and dust out.

Bearings with stainless steel balls are more corrosion resistant than bearings with steel balls.

Self-aligning bearings compensate for shaft misalignment.

Fixed-alignment bearings are for use where shaft misalignment is unlikely.

For technical drawings and 3-D models, click on a part number.

The choice for low-friction motion in high-temperature environments. Bearings are for use with round end-supported shafts and have a fixed-alignment design for applications where shaft misalignment is unlikely. To install, slide bearings into a housing (not included). For bearings with retaining ring grooves, secure with two retaining rings (sold individually).

For technical drawings and 3-D models, click on a part number.

Engineered for simultaneous linear and rotary motion, these bearings are used with round end-supported shafts. The fixed-alignment design is for use where shaft misalignment is unlikely. To install, slide bearings into a housing (not included) and secure with two retaining rings (sold individually).

Bearings with end seals are designed to keep lubricant in and dirt out.

Bearings without a maximum stroke length are only limited by the length of shaft they're used on.

For technical drawings and 3-D models, click on a part number.

Designed to handle heavy loads, these bearings have higher load capacities than comparable standard linear ball bearings. They are for use with round end-supported shafts and have a self-aligning design to compensate for shaft misalignment. To install, slide bearings into a housing (not included). For bearings with retaining ring grooves, secure with two retaining rings (sold individually).

Bearings with end seals keep lubricant in and dust out.

For technical drawings and 3-D models, click on a part number.

Bearings are for use with round end-supported shafts. To install, slide bearings into a housing (not included) and secure with two retaining rings (sold individually).

Bearings with 0.0005" shaft clearance are best for precision applications. Bearings with 0.001" or 0.0015" shaft clearance are less likely to bind on your shaft than bearings with 0.0005" shaft clearance.

Self Aligning—Bearings compensate for shaft misalignment.

Fixed Alignment—Bearings are for use where shaft misalignment is unlikely.

Frelon-lined bearings are wear and chemical resistant. Frelon-lined aluminum bearings have good corrosion resistance. Note: Not for use with bare aluminum, chrome-plated steel, or 300 series stainless steel shafts. Frelon-lined 316 stainless steel bearings have excellent corrosion resistance. Note: Not for use with chrome-plated steel.

PTFE-lined bearings are chemical resistant and nonabrasive. They have a ceramic coating for added corrosion resistance.

For technical drawings and 3-D models, click on a part number.

Ridges on the inside of these bearings wipe away dust and debris. To install, slide bearings into a housing (not included) and secure with two retaining rings (sold individually). All bearings are lined with lightweight, corrosion- and chemical-resistant PTFE.

Self-aligning bearings compensate for shaft misalignment. Fixed-alignment bearings are designed for use with round, end-supported shafts where shaft misalignment is unlikely.

6061 aluminum bearings have good corrosion resistance, and have a higher load capacity than bearings made entirely of PTFE.

For technical drawings and 3-D models, click on a part number.

A ceramic liner makes high speeds as well as rapid acceleration and deceleration possible. Bearings are for use with round end-supported shafts. They have a fixed-alignment design for applications where shaft misalignment is unlikely. To install, slide bearings into a housing (not included) and secure with two retaining rings (sold individually).

For technical drawings and 3-D models, click on a part number.

Made of FDA-listed materials for use in food applications, these bearings also have excellent chemical and corrosion resistance. They have a fixed-alignment design for applications where shaft misalignment is unlikely. To install, slide bearings into a housing (not included).

For bearings with retaining ring grooves, secure them in your housing with two retaining rings (sold individually).

For technical drawings and 3-D models, click on a part number.

These fiberglass bearings are lightweight, nonmagnetic, and won’t conduct electricity. Bearings are for use with round end-supported shafts. All have a fixed-alignment design for applications where shaft misalignment is unlikely. To install, slide bearings into a housing (not included) and secure with two retaining rings (sold individually).

For technical drawings and 3-D models, click on a part number.

Mount these bearings on a support rail shaft for applications requiring maximum rigidity. All have end seals to keep lubricant in and dirt out. To install, slide bearings into a housing (not included). For bearings with retaining ring grooves, secure with two retaining rings (sold individually).

Bearings with stainless steel balls are more corrosion resistant than bearings with steel balls.

Self-aligning bearings compensate for shaft misalignment.

Fixed-alignment bearings are for use where shaft misalignment is unlinkely.

For technical drawings and 3-D models, click on a part number.

Designed for heavy loads, these bearings have higher load capacities than comparable standard linear ball bearings for support rails. Use them for applications that require maximum rigidity. All are self-aligning to compensate for shaft misalignment. To install, slide bearings into a housing (not included). For bearings with retaining ring grooves, secure with two retaining rings (sold individually).

Bearings with end seals keep lubricants in and dirt out.

Bearings with stainless steel balls are more corrosion resistant than bearings with steel balls.

For technical drawings and 3-D models, click on a part number.

The choice for low-friction motion in high-temperature environments. Mount these bearings on a support rail shaft for applications requiring maximum rigidity. They have a fixed-alignment design for applications where shaft misalignment is unlikely. To install, slide bearings into a housing (not included) and secure in place with two retaining rings (sold separately).

For technical drawings and 3-D models, click on a part number.

Mount these bearings on a support rail shaft for applications requiring maximum rigidity. To install, slide bearings into a housing (not included) and secure with two retaining rings (sold individually).

Bearings with 0.0005" shaft clearance are best for precision applications. Bearings with 0.001" or 0.0015" shaft clearance are less likely to bind on your shaft than bearings with 0.0005" shaft clearance.

Self Aligning—Bearings compensate for shaft misalignment.

Fixed Alignment—Bearings are for use where shaft misalignment is unlikely.

Frelon-lined bearings are wear and chemical resistant. Note: Not for use with bare aluminum, chrome-plated steel, or 300 series stainless steel shafts.

PTFE-lined bearings are chemical resistant and nonabrasive. They have a ceramic coating for added corrosion resistance.

For technical drawings and 3-D models, click on a part number.

These bearings for use in food applications also have excellent chemical and corrosion resistance. Mount them on a support rail shaft for applications requiring maximum rigidity. They have a fixed-alignment design for applications where shaft misalignment is unlikely. To install, slide bearings into a housing (not included) and secure in place with two retaining rings (sold individually).

For technical drawings and 3-D models, click on a part number.

The flanged housing makes these bearings a good solution for vertical linear motion applications. All are for use with round end-supported shafts and have a fixed-alignment design for use where shaft misalignment is unlikely. End seals keep lubricant in and dirt out.

For technical drawings and 3-D models, click on a part number.

The bearing, housing, and balls of these mounted bearings are stainless steel for excellent corrosion resistance. The flanged housing is good for vertical linear motion applications. All bearings are for use with round end-supported shafts and have a fixed-alignment design for use where shaft misalignment is unlikely. End seals keep lubricant in and dirt out.

For technical drawings and 3-D models, click on a part number.

Replace worn or damaged wheel bearings to keep your equipment rolling. Use flanged bearings and ball bearings in pairs. Change the axle diameter with wheel reducer bushings (sold separately).

Note: Not for use in towing applications.

For impact-resistant tapered roller bearings, as well as other bearing materials and sizes, please see Ball and Roller Bearings and Sleeve Bearings.

Acetal bearings are a good choice for washdown and dusty environments.

Plain bearings prevent wear to the wheel bore.

Retaining washers hold roller bearings in place.

For technical drawings and 3-D models, click on a part number.

Reduce the inside diameter of a bearing to fit a particular axle size. Also known as spanner bushings, they also reduce wear on the axle when used in plain bores and with straight roller bearings. All have a hole for lubrication.

Washers slide over the bushing and add 3/32" to the hub length of your wheel. Multiple washers can be used to match the length of the bushing.

For technical drawings and 3-D models, click on a part number.

Mount flush with jig plates for precise drilling. These bushings can also be used as spacers, shims, and machinery bushings.

Don't see the size you need? Additional sizes are available.

For technical drawings and 3-D models, click on a part number.