System of Measurement System of Measurement |
---|
|
Mounted Bearing Type Mounted Bearing Type |
---|
![]() | ![]() |
Base Mount | Four-Bolt Flange Mount |
Length Length | Show |
---|
|
Length Length | Hide |
---|

Shaft Mount Type Shaft Mount Type |
---|
|
Lubrication Lubrication |
---|
|
For Shaft Type For Shaft Type |
---|
![]() | Round |
Seal Type Seal Type |
---|
|
Alignment Style Alignment Style |
---|
|
For Load Direction For Load Direction |
---|
![]() | Radial |
REACH (Registration, Evaluation, Authorization and Restriction of Chemicals) REACH (Registration,Evaluation, Authorization and Restriction of Chemicals) |
---|
|
DFARS (Defense Acquisition Regulations Supplement) DFARS (Defense AcquisitionRegulations Supplement) |
---|
RoHS (Restriction of Hazardous Substances) RoHS (Restriction ofHazardous Substances) |
---|
|
About Ball and Roller Bearings
More
Dry-Running Mounted Sleeve Bearings for Extreme Misalignment

These nylon bearings swivel inside their housing to compensate for over 20° of shaft misalignment. They are 80% lighter than steel bearings and resist corrosion, wear, shock, and vibration.
Note: Dynamic load capacity is the maximum load a bearing can withstand at a given shaft speed. If your application’s load and speed requirements are below the values listed, the bearing will work.
For technical drawings and 3-D models, click on a part number.
Overall, mm | Mounting | ||||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
For Shaft Dia., mm | Center Ht., mm | Ht. | Lg. | Wd. | Bearing Wd., mm | Hole Lg., mm | Hole Wd., mm | Hole Ctr.-to-Ctr., mm | Dynamic Radial Load Cap. | Temp. Range, °F | Alignment Style | Misalignment Capability | Specifications Met | Each | |
Nylon Plastic Bearings with Nylon Plastic Housing | |||||||||||||||
22 | 24 | 48 | 108 | 28 | 28 | 16 | 9 | 81 | Not Rated | -40° to 170° | Self Aligning | 22° | ISO 12240 | 0000000 | 000000 |
Mounted Ball Bearings with Four-Bolt Flange
Bearings are self-aligning to compensate for shaft misalignment. Seals block out dust and contaminants.
Set screw bearings secure to shafts as you tighten their screw. They don’t need a collar, but the screw leaves some marring on shafts. Use them in applications where shafts rotate in both directions.
Eccentric lock bearings are quick to install—twist them in one direction to tighten and the opposite to loosen. They’re better than set screw bearings for high speed applications, but they only work with shafts that rotate in one direction.
Concentric lock bearings enable high running speeds while maintaining low levels of vibration; you must pair them with an adapter sleeve (sold separately). They’re good for applications where shafts rotate in both directions.
For technical drawings and 3-D models, click on a part number.



Overall | Mounting | Radial Load Cap., lbs. | ||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
For Shaft Dia. | Ht. | Lg. | Wd. | Flange Thick. | Hole Dia. | Hole Ctr.-to-Ctr. | Dynamic | Static | Max. Speed, rpm | Temp. Range, °F | Alignment Style | Lubrication | Each | |
Sealed Steel Bearings with Cast Iron Housing | ||||||||||||||
Shaft Mount Type: Set Screw | ||||||||||||||
30mm | 108mm | 108mm | 39.7mm | 13.5mm | 11.9mm | 82.6mm | 4,350 | 2,550 | 5,400 | -20° to 220° | Self Aligning | Lubricated | 000000 | 0000000 |
Shaft Mount Type: Eccentric Lock | ||||||||||||||
30mm | 108mm | 108mm | 46.7mm | 13mm | 11.5mm | 82.5mm | 4,350 | 2,500 | 6,300 | -20° to 210° | Self Aligning | Lubricated | 0000000 | 000000 |
Shaft Mount Type: Concentric Lock | ||||||||||||||
25mm | 108mm | 108mm | 40.5mm | 13mm | 12mm | 83mm | 4,350 | 2,500 | 6,300 | -20° to 210° | Self Aligning | Lubricated | 0000000 | 000000 |

For Shaft Diameter, mm | ID, mm | Width, mm | Includes | Each | |
1137 Carbon Steel Sleeves | |||||
---|---|---|---|---|---|
25 | 25 | 38 | Lock Nut, Lock Washer | 00000000 | 000000 |