System of Measurement System of Measurement |
---|
|
For Shaft Diameter For Shaft Diameter |
---|
|
Mounted Bearing Type Mounted Bearing Type |
---|
![]() | ![]() |
Base Mount | Two-Bolt Flange Mount |
Housing Material Housing Material |
---|
|
Length Length | Show |
---|
|
Length Length | Hide |
---|

Shaft Mount Type Shaft Mount Type |
---|
|
ID ID |
---|
|
Seal Type Seal Type |
---|
|
For Load Direction For Load Direction |
---|
![]() | Radial |
Dynamic Radial Load Capacity Dynamic Radial Load Capacity |
---|
|
REACH (Registration, Evaluation, Authorization and Restriction of Chemicals) REACH (Registration,Evaluation, Authorization and Restriction of Chemicals) |
---|
|
RoHS (Restriction of Hazardous Substances) RoHS (Restriction ofHazardous Substances) |
---|
|
DFARS (Defense Acquisition Regulations Supplement) DFARS (Defense AcquisitionRegulations Supplement) |
---|
Maximum Temperature Maximum Temperature |
---|
|
Minimum Temperature Minimum Temperature |
---|
|
About Ball and Roller Bearings
More
Dry-Running Mounted Sleeve Bearings for Extreme Misalignment

These nylon bearings swivel inside their housing to compensate for over 20° of shaft misalignment. They are 80% lighter than steel bearings and resist corrosion, wear, shock, and vibration.
Note: Dynamic load capacity is the maximum load a bearing can withstand at a given shaft speed. If your application’s load and speed requirements are below the values listed, the bearing will work.
For technical drawings and 3-D models, click on a part number.
Overall, mm | Mounting | ||||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
For Shaft Dia., mm | Center Ht., mm | Ht. | Lg. | Wd. | Bearing Wd., mm | Hole Lg., mm | Hole Wd., mm | Hole Ctr.-to-Ctr., mm | Dynamic Radial Load Cap. | Temp. Range, °F | Alignment Style | Misalignment Capability | Specifications Met | Each | |
Nylon Plastic Bearings with Nylon Plastic Housing | |||||||||||||||
25 | 27 | 54 | 124 | 31 | 31 | 17 | 9 | 94 | Not Rated | -40° to 170° | Self Aligning | 22° | ISO 12240 | 0000000 | 000000 |
Mounted Ball Bearings with Two-Bolt Flange

Bearings are self-aligning to compensate for shaft misalignment. Seals block out dust and contaminants.
Bearings with an eccentric-lock shaft mount are better than bearings with a set-screw shaft mount for high-speed applications, but only rotate in a single direction.
For technical drawings and 3-D models, click on a part number.
Overall | Mounting | Radial Load Cap., lbs. | ||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
For Shaft Dia. | Ht. | Lg. | Wd. | Flange Thick. | Hole Dia. | Hole Ctr.-to-Ctr. | Dynamic | Static | Max. Speed, rpm | Temp. Range, °F | Alignment Style | Lubrication | Each | |
Sealed Steel Bearings with Cast Iron Housing | ||||||||||||||
Shaft Mount Type: Eccentric Lock | ||||||||||||||
25mm | 70mm | 124mm | 42.5mm | 12mm | 11.5mm | 99mm | 3,100 | 1,750 | 7,000 | -20° to 210° | Self Aligning | Lubricated | 00000000 | 0000000 |
Washdown Mounted Ball Bearings with Two-Bolt Flange
Used in food, beverage, pharmaceutical, and chemical plants, these mounted ball bearings are IP69K certified for washdown environments and have a two-bolt flange for mounting. Their 316 stainless steel housing has excellent corrosion resistance and prevents rust caused by salt water, chlorine solutions, and chemicals. All have USDA H1 approved lubrication, which is certified for incidental contact with food and is suitable for food and beverage applications.
Set screw bearings grip shafts as you tighten their screw. They don’t use a collar, but the screw leaves some marring on shafts.
Snap optional covers onto bearings to protect them from moisture. Made of polypropylene, they resist corrosion, don’t absorb water, and are FDA compliant.
For technical drawings and 3-D models, click on a part number.

Overall | Mounting | Radial Load Cap., lbs. | ||||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
For Shaft Dia. | Center Ht. | Ht. | Lg. | Wd. | Flange Thick. | Hole Dp. | Hole Ctr.-to-Ctr. | Dynamic | Static | Max. Speed, rpm | Temp. Range, °F | Alignment Style | Lubrication | Specifications Met | Each | |
Sealed Steel Bearings with 316 Stainless Steel Housing | ||||||||||||||||
Shaft Mount Type: Set Screw | ||||||||||||||||
25mm | 35mm | 70mm | 124mm | 62mm | 27mm | 27mm | 99mm | 2,800 | 1,650 | 2,000 | -20° to 220° | Self Aligning | Lubricated | NSF Registered H1 | 0000000 | 0000000 |


Permanently Lubricated Washdown Mounted Ball Bearings with Two-Bolt Flange
Permanently lubricated and IP69K certified for washdown environments, these mounted ball bearings are useful for hard-to-reach areas in food, beverage, pharmaceutical, and chemical plants. Mount them using their two-bolt flange. For excellent corrosion resistance and preventing rust caused by salt water, chlorine solutions, and chemicals, their housing is made of 316 stainless steel. All have NSF registered H1 lubrication, which is certified for incidental contact with food and is suitable for food and beverage applications.
Concentric lock bearings have a locking collar to center shafts and secure them better than set screw bearings, so there’s less vibration and noise. Install them by tightening the locking collar’s screw until it presses against the inner ring.
Snap optional covers onto bearings to shield them from moisture. Made of polypropylene, they resist corrosion, don’t absorb water, and are FDA compliant.
For technical drawings and 3-D models, click on a part number.

Overall | Radial Load Cap., lbs. | |||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
For Shaft Dia. | Ht. | Lg. | Wd. | Flange Thick. | Mounting Hole Ctr.-to-Ctr. | Dynamic | Static | Max. Speed, rpm | Temp. Range, °F | Alignment Style | Lubrication | Specifications Met | Each | |
Sealed Steel Bearings with 316 Stainless Steel Housing | ||||||||||||||
Shaft Mount Type: Concentric Lock | ||||||||||||||
25mm | 70mm | 124mm | 61.9mm | 13.5mm | 99mm | 2,800 | 1,650 | 2,000 | -20° to 220° | Self Aligning | Lubricated | NSF Registered H1 | 00000000 | 0000000 |

