System of Measurement System of Measurement |
---|
|
Length Length | Show |
---|
|
Length Length | Hide |
---|
OD OD |
---|
ID ID |
---|
|
Linear Bearing Component Linear Bearing Component |
---|
![]() | ![]() |
Bearing | Bearing in Housing |
For Shaft Type For Shaft Type |
---|
![]() | ![]() |
Round | Round with Support Rail |
For Shaft Material For Shaft Material |
---|
|
Housing Type Housing Type |
---|
![]() | ![]() |
Base Mount | Flange Mount |
Alignment Style Alignment Style |
---|
|
Lubrication Lubrication |
---|
|
Maximum Temperature Maximum Temperature |
---|
|
Minimum Temperature Minimum Temperature |
---|
|
Bearing Material Bearing Material |
---|
|
DFARS (Defense Acquisition Regulations Supplement) DFARS (Defense AcquisitionRegulations Supplement) |
---|
RoHS (Restriction of Hazardous Substances) RoHS (Restriction ofHazardous Substances) |
---|
|
REACH (Registration, Evaluation, Authorization and Restriction of Chemicals) REACH (Registration,Evaluation, Authorization and Restriction of Chemicals) |
---|
|
Material Material |
---|
|
About Linear Bearings
More
About Plain Bearings
More
Oil-Embedded Sleeve Bearings

Startup friction causes these porous bronze bearings to release a thin layer of oil on the bearing’s surface. They are also known as Oilite® bearings.
Note: Dynamic load capacity is the maximum load a bearing can withstand at a given shaft speed. If your application’s load and speed requirements are below the values listed, the bearing will work.
For technical drawings and 3-D models, click on a part number.
For Housing ID, mm | Lg., mm | Dynamic Radial Load Capacity | Lubrication | Lubricant | Temperature Range, °F | Each | |
For 16 mm Shaft Dia. | |||||||
---|---|---|---|---|---|---|---|
20 | 32 | 1,580 lbs. @ 60 rpm | Lubricated | SAE 30 Oil | -35° to 300° | 00000000 | 00000 |
For 20 mm Shaft Dia. | |||||||
24 | 32 | 1,950 lbs. @ 60 rpm | Lubricated | SAE 30 Oil | -35° to 300° | 00000000 | 0000 |
For 25 mm Shaft Dia. | |||||||
32 | 32 | 2,450 lbs. @ 60 rpm | Lubricated | SAE 30 Oil | -35° to 300° | 00000000 | 00000 |
For 32 mm Shaft Dia. | |||||||
40 | 32 | 3,150 lbs. @ 30 rpm | Lubricated | SAE 30 Oil | -35° to 300° | 00000000 | 00000 |
High-Load Oil-Embedded Sleeve Bearings

Increased iron content makes these bearings stronger and more resistant to shock loads than standard oil-embedded bearings; however they operate at lower speeds. Startup friction causes them to release a thin layer of oil on the bearing’s surface. Color is silver because of the iron. These bearings are also magnetic due to the high iron content.
Note: Dynamic load capacity is the maximum load a bearing can withstand at a given shaft speed. If your application’s load and speed requirements are below the values listed, the bearing will work.
For technical drawings and 3-D models, click on a part number.
For Housing ID | Lg. | Dynamic Radial Load Capacity | Lubrication | Lubricant | Temperature Range, °F | Each | |
For 32mm Shaft Dia. | |||||||
---|---|---|---|---|---|---|---|
40mm | 32mm | 5,600 lbs. @ 30 rpm | Lubricated | SAE 90 Oil | -15° to 300° | 00000000 | 000000 |
For Housing ID | Lg. | Dynamic Radial Load Capacity | Lubrication | Lubricant | Temperature Range, °F | Each | |
For 20mm Shaft Dia. | |||||||
---|---|---|---|---|---|---|---|
24mm | 32mm | 6,000 lbs. @ 60 rpm | Lubricated | SAE 90 Oil | 10° to 510° | 00000000 | 000000 |
Ultra-Low-Friction Oil-Embedded Sleeve Bearings

For applications with frequent starts and stops, the oil in these bearings contains particles of slippery PTFE that lubricate the bearing during startup.
Note: Dynamic load capacity is the maximum load a bearing can withstand at a given shaft speed. If your application’s load and speed requirements are below the values listed, the bearing will work.
For technical drawings and 3-D models, click on a part number.
For Housing ID, mm | Lg., mm | Dynamic Radial Load Capacity | Lubrication | Lubricant | Temperature Range, °F | Each | |
For 32mm Shaft Dia. | |||||||
---|---|---|---|---|---|---|---|
40 | 32 | 3,150 lbs. @ 30 rpm | Lubricated | SAE 20 Oil with PTFE | -60° to 300° | 00000000 | 000000 |
High-Load Ultra-Low-Friction Oil-Embedded Sleeve Bearings

With extra iron and filled with oil containing slippery PTFE, these bearings support heavy loads that frequently start and stop along shafts. Startup friction causes a thin layer of oil to release onto the surface. Their high iron content also means they resist failing if their load suddenly and drastically increases, but they won’t run as fast as standard bearings. As sleeve bearings, they handle loads parallel to the shaft.
Note: Dynamic load capacity is the maximum load a bearing can withstand at a given shaft speed. If your application’s load and speed requirements are below the values listed, the bearing will work.
For technical drawings and 3-D models, click on a part number.
For Housing ID, mm | Length, mm | Dynamic Radial Load Capacity | Lubrication | Lubricant | Temperature Range, °F | Each | |
863 Iron-Copper | |||||||
---|---|---|---|---|---|---|---|
For 25 mm Shaft Dia. | |||||||
32 | 32 | 2,800 lbs. @ 60 rpm | Lubricated | SAE 20 Oil with PTFE | -60° to 300° | 00000000 | 000000 |
Oil-Embedded Flanged Sleeve Bearings

Startup friction causes these porous bronze bearings to release a thin layer of oil on the bearing’s surface. They are also known as Oilite® bearings.
Note: Dynamic load capacity is the maximum load a bearing can withstand at a given shaft speed. If your application’s load and speed requirements are below the values listed, the bearing will work.
For technical drawings and 3-D models, click on a part number.
For Housing ID | Lg. | Flange OD | Flange Thick. | Dynamic Radial Load Capacity | Dynamic Thrust Load Capacity | Lubrication | Lubricant | Temperature Range, °F | Each | |
Metric 841 Bearing Bronze Bearings | ||||||||||
---|---|---|---|---|---|---|---|---|---|---|
For 20mm Shaft Dia. | ||||||||||
26mm | 32mm | 27mm | 3mm | 1,950 lbs. @ 60 rpm | 800 lbs. @ 60 rpm | Lubricated | SAE 30 Oil | 10° to 220° | 00000000 | 000000 |
For 32mm Shaft Dia. | ||||||||||
38mm | 32mm | 46mm | 4mm | 3,150 lbs. @ 30 rpm | 2,650 lbs. @ 30 rpm | Lubricated | SAE 30 Oil | -35° to 300° | 00000000 | 00000 |
For 35mm Shaft Dia. | ||||||||||
40mm | 32mm | 45mm | 2.5mm | 3,450 lbs. @ 30 rpm | 1,900 lbs. @ 30 rpm | Lubricated | SAE 30 Oil | -35° to 300° | 00000000 | 00000 |
For 45mm Shaft Dia. | ||||||||||
51mm | 32mm | 57mm | 3mm | 4,450 lbs. @ 30 rpm | 2,950 lbs. @ 30 rpm | Lubricated | SAE 30 Oil | -35° to 300° | 00000000 | 00000 |
For 50mm Shaft Dia. | ||||||||||
60mm | 32mm | 70mm | 5mm | 4,950 lbs. @ 30 rpm | 5,800 lbs. @ 30 rpm | Lubricated | SAE 30 Oil | -35° to 300° | 00000000 | 00000 |
High-Load Oil-Embedded Flanged Sleeve Bearings

Increased iron content makes these bearings stronger and more resistant to shock loads than standard oil-embedded bearings; however they operate at lower speeds. Startup friction causes these bearings to release a thin layer of oil onto their surface. Color is silver because of the iron.
863 iron-copper bearings are also known as Super Oilite® bearings.
Note: Dynamic load capacity is the maximum load a bearing can withstand at a given shaft speed. If your application’s load and speed requirements are below the values listed, the bearing will work.
For technical drawings and 3-D models, click on a part number.
For Housing ID | Lg. | Flange OD | Flange Thick. | Dynamic Radial Load Capacity | Dynamic Thrust Load Capacity | Lubrication | Lubricant | Temperature Range, °F | Each | |
863 Iron-Copper Bearings | ||||||||||
---|---|---|---|---|---|---|---|---|---|---|
For 32mm Shaft Dia. | ||||||||||
38mm | 32mm | 46mm | 4mm | 5,600 lbs. @ 30 rpm | 3,250 lbs. @ 30 rpm | Lubricated | ISO 460 Oil | -15° to 300° | 00000000 | 000000 |
For 35mm Shaft Dia. | ||||||||||
40mm | 32mm | 45mm | 2.5mm | 5,600 lbs. @ 30 rpm | 2,400 lbs. @ 30 rpm | Lubricated | ISO 460 Oil | -15° to 300° | 0000000 | 00000 |
For 45mm Shaft Dia. | ||||||||||
51mm | 32mm | 57mm | 3mm | 5,600 lbs. @ 30 rpm | 2,950 lbs. @ 30 rpm | Lubricated | ISO 460 Oil | -15° to 300° | 00000000 | 00000 |
For 50mm Shaft Dia. | ||||||||||
60mm | 32mm | 70mm | 5mm | 5,600 lbs. @ 30 rpm | 4,700 lbs. @ 30 rpm | Lubricated | ISO 460 Oil | -15° to 300° | 00000000 | 00000 |
High-Load Ultra-Low-Friction Oil-Embedded Flanged Sleeve Bearings

With oil for reduced friction and iron for added strength, these bearings handle frequent stops and starts in high-load applications. They withstand greater weight and shock loads than standard bearings, but operate at lower speeds.
For technical drawings and 3-D models, click on a part number.
For Housing ID, mm | Length, mm | Flange OD, mm | Flange Thickness, mm | Dynamic Radial Load Capacity | Dynamic Thrust Load Capacity | Lubrication | Lubricant | Temperature Range, °F | Each | |
863 Iron-Copper Bearings | ||||||||||
---|---|---|---|---|---|---|---|---|---|---|
32 mm Shaft Dia. | ||||||||||
38 | 32 | 46 | 4 | 5,600 lbs. @ 30 rpm | 3,250 lbs. @ 30 rpm | Lubricated | ISO 460 Oil | -60° to 300° | 00000000 | 000000 |
35 mm Shaft Dia. | ||||||||||
40 | 32 | 45 | 2.5 | 5,600 lbs. @ 30 rpm | 2,400 lbs. @ 30 rpm | Lubricated | ISO 460 Oil | -60° to 300° | 00000000 | 00000 |
45 mm Shaft Dia. | ||||||||||
51 | 32 | 57 | 3 | 5,600 lbs. @ 30 rpm | 2,950 lbs. @ 30 rpm | Lubricated | ISO 460 Oil | -60° to 300° | 00000000 | 00000 |
50 mm Shaft Dia. | ||||||||||
60 | 32 | 70 | 5 | 5,600 lbs. @ 30 rpm | 4,700 lbs. @ 30 rpm | Lubricated | ISO 460 Oil | -60° to 300° | 00000000 | 00000 |
Multipurpose Flanged Sleeve Bearings

These leaded bronze bearings are strong, wear resistant, and excellent at handling shock loads. They’re sometimes called 932 bronze bearings.
Note: Dynamic load capacity is the maximum load a bearing can withstand at a given shaft speed. If your application’s load and speed requirements are below the values listed, the bearing will work.
For technical drawings and 3-D models, click on a part number.
For Housing ID | Lg. | Flange OD | Flange Thick. | Dynamic Radial Load Capacity | Dynamic Thrust Load Capacity | Lubrication | Temperature Range, °F | PV Max. | Each | |
Metric 660 Leaded Bronze Bearings | ||||||||||
---|---|---|---|---|---|---|---|---|---|---|
For 28mm Shaft Dia. | ||||||||||
36mm | 32mm | 44mm | 4mm | 5,550 lbs. @ 30 rpm | 5,600 lbs. @ 30 rpm | Required | -350° to 450° | __ | 00000000 | 000000 |
For 32mm Shaft Dia. | ||||||||||
38mm | 32mm | 46mm | 4mm | 6,300 lbs. @ 30 rpm | 5,300 lbs. @ 30 rpm | Required | -350° to 450° | 75,000 | 00000000 | 00000 |
For 45mm Shaft Dia. | ||||||||||
51mm | 32mm | 57mm | 3mm | 8,900 lbs. @ 30 rpm | 5,950 lbs. @ 30 rpm | Required | -350° to 450° | 75,000 | 0000000 | 00000 |
Linear Ball Bearings

Bearings are for use with round end-supported shafts. To install, slide bearings into a housing (not included). For bearings with retaining ring grooves, secure with two retaining rings (sold individually).
Bearings with end seals keep lubricant in and dust out.
Bearings with stainless steel balls are more corrosion resistant than bearings with steel balls.
Fixed-alignment bearings are for use where shaft misalignment is unlikely.
For technical drawings and 3-D models, click on a part number.

Bearings | ||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|
Load Capacity, lbs. | External Retaining Rings | |||||||||||
For Shaft Dia., mm | Overall Lg., mm | For Housing ID, mm | Retaining Ring Groove End-to-End Lg., mm | With End Seals | Dynamic | Static | Temperature Range, °F | For Shaft Material | Each | Each | ||
440C Stainless Steel Bearings with Stainless Steel Balls | ||||||||||||
13 | 32 | 23.000 - 23.021 | 23 | Yes | 110 | 175 | -4° to 176° | Stainless Steel, Steel | 0000000 | 000000 | 0000000 | 00000 |
Steel Bearings with Steel Balls | ||||||||||||
13 | 32 | 23.000 - 23.021 | 23 | Yes | 110 | 175 | -4° to 176° | Stainless Steel, Steel | 00000000 | 00000 | 0000000 | 000 |
High-Temperature Linear Ball Bearings

The choice for low-friction motion in high-temperature environments. Bearings are for use with round end-supported shafts and have a fixed-alignment design for applications where shaft misalignment is unlikely. To install, slide bearings into a housing (not included). For bearings with retaining ring grooves, secure with two retaining rings (sold individually).
Stainless steel bearings are more corrosion resistant than steel bearings.
For technical drawings and 3-D models, click on a part number.

Bearings | |||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|
Load Capacity, lbs. | External Retaining Rings | ||||||||||||
For Shaft Diameter, mm | Overall Lg., mm | For Housing ID, mm | Retaining Ring Groove End-to-End Length, mm | With End Seals | Dynamic | Static | Dynamic Load Capacity at Maximum Temperature | Temperature Range, ° F | For Shaft Material | Each | Each | ||
440C Stainless Steel Bearings with Stainless Steel Balls | |||||||||||||
12 | 32 | 22.000 - 22.021 | 22.9 | Yes | 110 | 175 | 110 lbs. @ 248° F | -4° to 248° | Stainless Steel, Steel | 0000000 | 000000 | 0000000 | 00000 |
Linear and Rotary Ball Bearings


Engineered for simultaneous linear and rotary motion, these bearings are used with round end-supported shafts. The fixed-alignment design is for use where shaft misalignment is unlikely. To install, slide bearings into a housing (not included) and secure with two retaining rings (sold individually).
Bearings with end seals are designed to keep lubricant in and dirt out.
For technical drawings and 3-D models, click on a part number.
Bearings | External Retaining Rings | |||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
For Shaft Dia. | Overall Lg. | For Housing ID | Retaining Ring Groove End-to-End Lg. | Dynamic Load Capacity, lbs. | Dynamic Rotary Load Capacity | Max. Speed, rpm | Max. Temperature, ° F | Max. Stroke Lg. | For Shaft Material | Each | Pkg. Qty. | Pkg. | ||
Fixed Alignment | ||||||||||||||
Steel Bearings with End Seals | ||||||||||||||
12mm | 32mm | 23.0000mm - 23.0210mm | 20.1mm | 240 | 99 lbs. @ 500 rpm | 5,000 | 200° | 18mm | Stainless Steel, Steel | 0000000 | 000000 | 1 | 0000000 | 00000 |
High-Load Linear Ball Bearings

Designed to handle heavy loads, these bearings have higher load capacities than comparable standard linear ball bearings. They are for use with round end-supported shafts and have a self-aligning design to compensate for shaft misalignment. To install, slide bearings into a housing (not included). For bearings with retaining ring grooves, secure with two retaining rings (sold individually).
For technical drawings and 3-D models, click on a part number.

Bearings | External Retaining Rings | |||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|
For Shaft Dia., mm | Overall Lg., mm | For Housing ID, mm | OD, mm | Retaining Ring Groove End-to-End Lg., mm | With End Seals | Dynamic Load Capacity, lbs. | Max. Temperature, °F | For Shaft Material | Each | Each | ||
Acetal Bearings with Steel Balls | ||||||||||||
12 | 32 | 22.000 - 22.018 | 22 | 22.6 | No | 200 | 176° | Stainless Steel; Steel | 0000000 | 000000 | 0000000 | 00000 |
Linear Sleeve Bearings


Bearings are for use with round end-supported shafts. To install, slide bearings into a housing (not included) and secure with two retaining rings (sold individually).
Bearings with 0.0005" shaft clearance are best for precision applications. Bearings with 0.001" or 0.0015" shaft clearance are less likely to bind on your shaft than bearings with 0.0005" shaft clearance.
Self Aligning—Bearings compensate for shaft misalignment.
Fixed Alignment—Bearings are for use where shaft misalignment is unlikely.
Frelon-lined bearings are wear and chemical resistant. Frelon-lined aluminum bearings have good corrosion resistance. Note: Not for use with bare aluminum, chrome-plated steel, or 300 series stainless steel shafts.
PTFE-lined bearings are chemical resistant and nonabrasive. They have a ceramic coating for added corrosion resistance.
For technical drawings and 3-D models, click on a part number.
Bearings | External Retaining Rings | |||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|
For Shaft Dia., mm | Shaft Clearance | Overall Lg., mm | For Housing ID, mm | Retaining Ring Groove End-to-End Lg., mm | Dynamic Load Capacity | Static Load Capacity, lbs. | Temperature Range, ° F | For Shaft Material | Each | Each | ||
PTFE-Lined 6061 Aluminum Bearings | ||||||||||||
12 | 0.001" | 32 | 22.000 - 22.021 | 22.6 | 150 lbs. @ 100 fpm | 2,200 | -400° to 375° | Aluminum, Stainless Steel | 0000000 | 000000 | 0000000 | 00000 |
Bearings | External Retaining Rings | |||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|
For Shaft Dia., mm | Shaft Clearance | Overall Lg., mm | For Housing ID, mm | Retaining Ring Groove End-to-End Lg., mm | Dynamic Load Capacity | Static Load Capacity, lbs. | Temperature Range, ° F | For Shaft Material | Each | Each | ||
Frelon-Lined 6061 Aluminum Bearings | ||||||||||||
12 | 0.0005" | 32 | 22.020 - 22.053 | 22.64 | 100 lbs. @ 100 fpm | 1,700 | -400° to 400° | Steel | 00000000 | 000000 | 0000000 | 00000 |
PTFE-Lined 6061 Aluminum Bearings | ||||||||||||
12 | 0.001" | 32 | 22.000 - 22.021 | 22.6 | 150 lbs. @ 100 fpm | 2,200 | -400° to 375° | Aluminum, Stainless Steel | 0000000 | 00000 | 0000000 | 0000 |
Dust-Resistant Linear Sleeve Bearings



Ridges on the inside of these bearings wipe away dust and debris. To install, slide bearings into a housing (not included) and secure with two retaining rings (sold individually). All bearings are lined with lightweight, corrosion- and chemical-resistant PTFE.
Self-aligning bearings compensate for shaft misalignment. Fixed-alignment bearings are designed for use with round, end-supported shafts where shaft misalignment is unlikely.
6061 aluminum bearings have good corrosion resistance, and have a higher load capacity than bearings made entirely of PTFE.
For technical drawings and 3-D models, click on a part number.
Bearings | External Retaining Rings | ||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|
For Shaft Dia. | Overall Lg. | For Housing ID | Retaining Ring Groove End-to-End Lg. | Dynamic Load Capacity | Static Load Capacity, lbs. | Shaft Clearance | Temperature Range, ° F | For Shaft Material | Each | Pkg. Qty. | Pkg. | ||
Self Aligning | |||||||||||||
6061 Aluminum Bearings | |||||||||||||
12mm | 32mm | 22.000mm - 22.021mm | 22.8mm | 55 lbs. @ 100 fpm | 1,500 | 0.03mm to 0.088mm | -40° to 194° | Aluminum, Stainless Steel, Steel | 00000000 | 000000 | 1 | 0000000 | 00000 |
Fixed Alignment | |||||||||||||
PTFE Plastic Bearings | |||||||||||||
12mm | 32mm | 22.000mm - 22.021mm | 22.6mm | 55 lbs. @ 100 fpm | 755 | 0.032mm to 0.075mm | -40° to 194° | Aluminum, Stainless Steel, Steel | 00000000 | 00000 | 1 | 0000000 | 0000 |
6061 Aluminum Bearings | |||||||||||||
12mm | 32mm | 22.000mm - 22.021mm | 22.6mm | 55 lbs. @ 100 fpm | 1,500 | 0mm to 0.058mm | -40° to 194° | Aluminum, Stainless Steel, Steel | 00000000 | 00000 | 1 | 0000000 | 0000 |
High-Speed Linear Sleeve Bearings

A ceramic liner makes high speeds as well as rapid acceleration and deceleration possible. Bearings are for use with round end-supported shafts. They have a fixed-alignment design for applications where shaft misalignment is unlikely. To install, slide bearings into a housing (not included) and secure with two retaining rings (sold individually).
For technical drawings and 3-D models, click on a part number.
Bearings | External Retaining Rings | |||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|
For Shaft Dia. | Overall Lg. | For Housing ID | Retaining Ring Groove End-to-End Lg. | Dynamic Load Capacity | Static Load Capacity, lbs. | Shaft Clearance | Temperature Range, ° F | For Shaft Material | Each | Pkg. of 1 | ||
Fixed Alignment | ||||||||||||
Ceramic-Lined 6061 Aluminum Bearings | ||||||||||||
12mm | 32mm | 22 mm | 20mm | 150 lbs. @ 100 fpm | 2,950 | 0.0127mm to 0.0381mm | -200° to 400° | Stainless Steel, Steel | 0000000 | 000000 | 0000000 | 00000 |
Food Industry Linear Sleeve Bearings

Made of FDA-listed materials for use in food applications, these bearings also have excellent chemical and corrosion resistance. They have a fixed-alignment design for applications where shaft misalignment is unlikely. To install, slide bearings into a housing (not included).
For bearings with retaining ring grooves, secure them in your housing with two retaining rings (sold individually).
For technical drawings and 3-D models, click on a part number.
Bearings | External Retaining Rings | ||||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
For Shaft Dia. | Overall Lg. | For Housing ID | With Retaining Ring Grooves | Retaining Ring Groove End-to-End Lg. | Dynamic Load Capacity | Static Load Capacity, lbs. | Shaft Clearance | Temperature Range, ° F | For Shaft Material | Specifications Met | Each | Pkg. Qty. | Pkg. | ||
Fixed Alignment | |||||||||||||||
Rulon 641-Lined 304 Stainless Steel Bearings | |||||||||||||||
12mm | 32mm | 22.000mm - 22.021mm | Yes | 22.6mm | 55 lbs. @ 100 fpm | 130 | 0.05mm | -400° to 375° | Aluminum, Stainless Steel | FDA Compliant 21 CFR 177.1380 | 0000000 | 000000 | 1 | 0000000 | 00000 |
Linear Ball Bearings for Support Rail Shafts
Mount these bearings on a support rail shaft for applications requiring maximum rigidity. All have end seals to keep lubricant in and dirt out. To install, slide bearings into a housing (not included). For bearings with retaining ring grooves, secure with two retaining rings (sold individually).
Bearings with stainless steel balls are more corrosion resistant than bearings with steel balls.
Fixed-alignment bearings are for use where shaft misalignment is unlinkely.
For technical drawings and 3-D models, click on a part number.

Bearings | |||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|
Load Capacity, lbs. | External Retaining Rings | ||||||||||||
For Shaft Dia., mm | Overall Lg., mm | Wd., mm | For Housing ID, mm | With Retaining Ring Grooves | Retaining Ring Groove End-to-End Lg., mm | Dynamic | Static | Temp. Range, °F | For Shaft Material | Each | Each | ||
440C Stainless Steel Bearings with Stainless Steel Balls | |||||||||||||
12 | 32 | 7.5 | 22.000 - 22.021 | Yes | 22.9 | 110 | 175 | -4° to 176° | Stainless Steel, Steel | 00000000 | 000000 | 0000000 | 00000 |
Steel Bearings with Steel Balls | |||||||||||||
12 | 32 | 7.5 | 22.000 - 22.021 | Yes | 22.9 | 110 | 175 | -4° to 176° | Stainless Steel, Steel | 000000000 | 00000 | 0000000 | 0000 |
High-Load Linear Ball Bearings for Support Rail Shafts

Designed for heavy loads, these bearings have higher load capacities than comparable standard linear ball bearings for support rails. Use them for applications that require maximum rigidity. All are self-aligning to compensate for shaft misalignment. To install, slide bearings into a housing (not included). For bearings with retaining ring grooves, secure with two retaining rings (sold individually).
Bearings with end seals keep lubricants in and dirt out.
Bearings with stainless steel balls are more corrosion resistant than bearings with steel balls.
Bearings | External Retaining Rings | ||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|
For Shaft Dia., mm | Overall Lg., mm | Wd., mm | For Housing ID, mm | With Retaining Ring Grooves | Retaining Ring Groove End-to-End Lg., mm | With End Seals | Dynamic Load Capacity, lbs. | Max. Temperature, ° F | For Shaft Material | Each | Each | ||
Acetal Plastic Bearings with Stainless Steel Balls | |||||||||||||
12 | 32 | 7 | 22.000 - 22.026 | Yes | 22.3 | Yes | 235 | 185° | Stainless Steel, Steel | 0000000 | 000000 | 000000000 | 00000 |
Acetal Plastic Bearings with Steel Balls | |||||||||||||
12 | 32 | 7 | 22.000 - 22.018 | Yes | 22.3 | No | 235 | 176° | Stainless Steel, Steel | 0000000 | 00000 | 000000000 | 0000 |
Food Industry Linear Sleeve Bearings for Support Rail Shafts

These bearings for use in food applications also have excellent chemical and corrosion resistance. Mount them on a support rail shaft for applications requiring maximum rigidity. They have a fixed-alignment design for applications where shaft misalignment is unlikely. To install, slide bearings into a housing (not included) and secure in place with two retaining rings (sold individually).
For technical drawings and 3-D models, click on a part number.
Bearings | External Retaining Rings | |||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
For Shaft Dia. | Overall Lg. | Wd. | For Housing ID | Retaining Ring Groove End-to-End Lg. | Dynamic Load Capacity | Static Load Capacity, lbs. | Shaft Clearance | Temperature Range, ° F | For Shaft Material | Each | Pkg. Qty. | Pkg. | ||
Fixed Alignment | ||||||||||||||
Rulon 641-Lined 304 Stainless Steel Bearings | ||||||||||||||
12mm | 32mm | 7.6mm | 22.0000mm - 22.0210mm | 20mm | 60 lbs. @ 100 fpm | 590 | 0.05mm | -400° to 375° | Aluminum, Stainless Steel | 0000000 | 000000 | 1 | 0000000 | 00000 |
High-Speed Linear Sleeve Bearings for Support Rail Shafts

These bearings have a ceramic liner to help them achieve high speeds as well as rapid acceleration and deceleration. Mount them on support rail shafts for applications requiring maximum rigidity. To install, slide bearings into a housing (not included) and secure in place with two retaining rings (sold individually).
Fixed-alignment bearings are for use where shaft misalignment is unlikely.
Self-aligning bearings compensate for shaft misalignment.
For technical drawings and 3-D models, click on a part number.
Bearings | External Retaining Rings | |||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
For Shaft Dia., mm | Shaft Clearance | Overall Length, mm | Wd., mm | For Housing ID, mm | Retaining Ring Groove End-to-End Length, mm | Dynamic Load Capacity | Static Load Capacity, lbs. | Temperature Range, °F | For Shaft Material | Each | Pkg. Qty. | Pkg. | ||
Ceramic-Lined 6061 Aluminum Bearings | ||||||||||||||
12 | 0.001" | 32 | 7.6 | 22.0000 - 22.0210 | 22.6 | 150 lbs. @ 100 fpm | 2,200 | -400° to 400° | Stainless Steel, Steel | 0000000 | 000000 | 1 | 0000000 | 00000 |
Bearings | External Retaining Rings | |||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
For Shaft Dia., mm | Shaft Clearance | Overall Length, mm | Wd., mm | For Housing ID, mm | Retaining Ring Groove End-to-End Length, mm | Dynamic Load Capacity | Static Load Capacity, lbs. | Temperature Range, °F | For Shaft Material | Each | Pkg. Qty. | Pkg. | ||
Ceramic-Lined 6061 Aluminum Bearings | ||||||||||||||
12 | 0.001" | 32 | 7.6 | 22.0000 - 22.0210 | 22.6 | 150 lbs. @ 100 fpm | 2,200 | -400° to 400° | Stainless Steel, Steel | 0000000 | 000000 | 1 | 0000000 | 00000 |
Flange-Mounted Linear Ball Bearings


The flanged housing makes these bearings a good solution for vertical linear motion applications. All are for use with round end-supported shafts and have a fixed-alignment design for use where shaft misalignment is unlikely. End seals keep lubricant in and dirt out.
For technical drawings and 3-D models, click on a part number.
Overall, mm | Flange, mm | Load Capacity, lbs. | Mounting Holes | ||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
For Shaft Dia., mm | Lg. | Wd. | Ht. | Thick. | OD | Bolt Circle Dia., mm | OD, mm | Dynamic | Static | Temperature Range, ° F | For Shaft Material | No. of | Dia., mm | Each | |
Steel Bearings with Round Flanged Housing | |||||||||||||||
12 | 32 | 42 | 42 | 6 | 42 | 32 | 22 | 110 | 175 | -4° to 176° | Stainless Steel, Steel | 4 | 4.5 | 00000000 | 000000 |
Steel Bearings with Square Flanged Housing | |||||||||||||||
12 | 32 | 32 | 32 | 6 | __ | 32 | 22 | 110 | 175 | -4° to 176° | Stainless Steel, Steel | 4 | 4.5 | 00000000 | 00000 |
Corrosion-Resistant Mounted Linear Ball Bearings

Outdoor as well as mild chemical environments are no problem for these bearings. They have stainless steel balls for corrosion resistance. All bearings are for use with round end-supported shafts and have end seals to keep lubricant in and dirt out.
Self-aligning bearings compensate for shaft misalignment.
Bearings with aluminum housing take on heavier loads than bearings with an acetal housing.
For technical drawings and 3-D models, click on a part number.
Overall, mm | Load Capacity, lbs. | Mounting Holes | ||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|
For Shaft Dia., mm | Lg. | Wd. | Ht. | Center Ht., mm | Dynamic | Static | Temperature Range, °F | For Shaft Material | No. of | Dia., mm | Each | |
Acetal Bearings with Stainless Steel Balls in 6061 Aluminum Housing | ||||||||||||
8 | 32 | 35 | 28 | 15 | 95 | 120 | -4° to 176° | Stainless Steel, Steel | 4 | 4 | 0000000 | 0000000 |
Metric Press-Fit Drill Bushings

Also known as jig bushings, these metric drill bushings fit inside fixture plate holes to guide drill bits, counterbores, reamers, and other cutting tools. They improve accuracy so that your drilled holes and cuts are consistent from part to part. Known for their versatility, drill bushings are also used as spacers, shims, and machinery bushings. These bushings are made of hardened, ground steel that holds its shape and resists wear, so they last for many cycles without needing to be replaced.
All bushings have a chamfer on the outside that centers the bushing as you place it into the hole. Press into place with a manual or hydraulic press. They also have internal chamfers, so it's easier to insert bits, pins, and punches into the bushing. DIN 179 bushings meet dimensional and material standards that make sure they're compatible with other parts and tools. Although DIN 179 is no longer an active standard, it's still a common reference point for designers.
Don't see the size you need? Additional sizes are available.
For technical drawings and 3-D models, click on a part number.
Tolerance | Each | |||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
OD, mm | Lg., mm | Internal Chamfer | For Drill Bit Size | ID, mm | OD, mm | Lg., mm | Drill Bushing Type | Material | Hardness | Specifications Met | 1-5 | 6-11 | 12-Up | |
21.25 mm ID | ||||||||||||||
35 | 32 | One End | 21.25 mm | 0.02 to 0.041 | 0.017 to 0.033 | -0.3 to 0.3 | PM | Steel | Rockwell C61 | DIN 179 | 000000000 | 000000 | 000000 | 000000 |
Metric Press-Fit Drill Bushings with Head




Even under extreme drilling pressure, these metric bushings won't press through your jig plate. A flanged head on the top of the bushing acts as a stop, preventing it from moving as you push down your drill bit, reamer, or other cutting bit. Drill bushings ensure accurate, consistent cuts and drilled holes from one part to the next. They sometimes also work as spacers, shims, and machinery bushings. Made of hardened, ground steel, these bushings hold their shape and resist wear over time. The flanged head protects your jig plate from damage caused by heavy use.
Although it's no longer an active standard, DIN 172 is still a common reference point for making sure parts are compatible with other parts and tools.
These bushings work in both countersunk and standard drill holes. To install, place the bushing inside the hole in your jig. A chamfered edge on the bottom of the bushing helps center the bushing in the hole. Once centered, press the bushing into the hole with a hydraulic or lever press.
For technical drawings and 3-D models, click on a part number.
Head | Tolerance | Each | ||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
OD, mm | Lg., mm | OD, mm | Thick., mm | ID, mm | OD, mm | Lg., mm | Drill Bushing Type | Material | Hardness | Specifications Met | 1-5 | 6-11 | 12-Up | |
12.1 mm ID | ||||||||||||||
22 | 32 | 26 | 4 | 0.016 to 0.034 | 0.015 to 0.028 | -0.3 to 0.3 | H | Steel | Rockwell C61 | DIN 172 | 000000000 | 000000 | 000000 | 000000 |
12.2 mm ID | ||||||||||||||
22 | 32 | 26 | 4 | 0.016 to 0.034 | 0.015 to 0.028 | -0.3 to 0.3 | H | Steel | Rockwell C61 | DIN 172 | 000000000 | 00000 | 00000 | 00000 |
12.3 mm ID | ||||||||||||||
22 | 32 | 26 | 4 | 0.016 to 0.034 | 0.015 to 0.028 | -0.3 to 0.3 | H | Steel | Rockwell C61 | DIN 172 | 000000000 | 00000 | 00000 | 00000 |
12.4 mm ID | ||||||||||||||
22 | 32 | 26 | 4 | 0.016 to 0.034 | 0.015 to 0.028 | -0.3 to 0.3 | H | Steel | Rockwell C61 | DIN 172 | 000000000 | 00000 | 00000 | 00000 |
12.5 mm ID | ||||||||||||||
22 | 32 | 26 | 4 | 0.016 to 0.034 | 0.015 to 0.028 | -0.3 to 0.3 | H | Steel | Rockwell C61 | DIN 172 | 000000000 | 00000 | 00000 | 00000 |
12.6 mm ID | ||||||||||||||
22 | 32 | 26 | 4 | 0.016 to 0.034 | 0.015 to 0.028 | -0.3 to 0.3 | H | Steel | Rockwell C61 | DIN 172 | 000000000 | 00000 | 00000 | 00000 |
12.7 mm ID | ||||||||||||||
22 | 32 | 26 | 4 | 0.016 to 0.034 | 0.015 to 0.028 | -0.3 to 0.3 | H | Steel | Rockwell C61 | DIN 172 | 000000000 | 00000 | 00000 | 00000 |
12.8 mm ID | ||||||||||||||
22 | 32 | 26 | 4 | 0.016 to 0.034 | 0.015 to 0.028 | -0.3 to 0.3 | H | Steel | Rockwell C61 | DIN 172 | 000000000 | 00000 | 00000 | 00000 |
12.9 mm ID | ||||||||||||||
22 | 32 | 26 | 4 | 0.016 to 0.034 | 0.015 to 0.028 | -0.3 to 0.3 | H | Steel | Rockwell C61 | DIN 172 | 000000000 | 00000 | 00000 | 00000 |
13 mm ID | ||||||||||||||
22 | 32 | 26 | 4 | 0.016 to 0.034 | 0.015 to 0.028 | -0.3 to 0.3 | H | Steel | Rockwell C61 | DIN 172 | 000000000 | 00000 | 00000 | 00000 |
13.1 mm ID | ||||||||||||||
22 | 32 | 26 | 4 | 0.016 to 0.034 | 0.015 to 0.028 | -0.3 to 0.3 | H | Steel | Rockwell C61 | DIN 172 | 000000000 | 00000 | 00000 | 00000 |
13.2 mm ID | ||||||||||||||
22 | 32 | 26 | 4 | 0.016 to 0.034 | 0.015 to 0.028 | -0.3 to 0.3 | H | Steel | Rockwell C61 | DIN 172 | 000000000 | 00000 | 00000 | 00000 |
13.3 mm ID | ||||||||||||||
22 | 32 | 26 | 4 | 0.016 to 0.034 | 0.015 to 0.028 | -0.3 to 0.3 | H | Steel | Rockwell C61 | DIN 172 | 000000000 | 00000 | 00000 | 00000 |
13.4 mm ID | ||||||||||||||
22 | 32 | 26 | 4 | 0.016 to 0.034 | 0.015 to 0.028 | -0.3 to 0.3 | H | Steel | Rockwell C61 | DIN 172 | 000000000 | 00000 | 00000 | 00000 |
13.5 mm ID | ||||||||||||||
22 | 32 | 26 | 4 | 0.016 to 0.034 | 0.015 to 0.028 | -0.3 to 0.3 | H | Steel | Rockwell C61 | DIN 172 | 000000000 | 00000 | 00000 | 00000 |
13.6 mm ID | ||||||||||||||
22 | 32 | 26 | 4 | 0.016 to 0.034 | 0.015 to 0.028 | -0.3 to 0.3 | H | Steel | Rockwell C61 | DIN 172 | 000000000 | 00000 | 00000 | 00000 |
13.7 mm ID | ||||||||||||||
22 | 32 | 26 | 4 | 0.016 to 0.034 | 0.015 to 0.028 | -0.3 to 0.3 | H | Steel | Rockwell C61 | DIN 172 | 000000000 | 00000 | 00000 | 00000 |
13.8 mm ID | ||||||||||||||
22 | 32 | 26 | 4 | 0.016 to 0.034 | 0.015 to 0.028 | -0.3 to 0.3 | H | Steel | Rockwell C61 | DIN 172 | 000000000 | 00000 | 00000 | 00000 |
13.9 mm ID | ||||||||||||||
22 | 32 | 26 | 4 | 0.016 to 0.034 | 0.015 to 0.028 | -0.3 to 0.3 | H | Steel | Rockwell C61 | DIN 172 | 000000000 | 00000 | 00000 | 00000 |
14 mm ID | ||||||||||||||
22 | 32 | 26 | 4 | 0.016 to 0.034 | 0.015 to 0.028 | -0.3 to 0.3 | H | Steel | Rockwell C61 | DIN 172 | 000000000 | 00000 | 00000 | 00000 |
14.1 mm ID | ||||||||||||||
22 | 32 | 26 | 4 | 0.016 to 0.034 | 0.015 to 0.028 | -0.3 to 0.3 | H | Steel | Rockwell C61 | DIN 172 | 000000000 | 00000 | 00000 | 00000 |
14.2 mm ID | ||||||||||||||
22 | 32 | 26 | 4 | 0.016 to 0.034 | 0.015 to 0.028 | -0.3 to 0.3 | H | Steel | Rockwell C61 | DIN 172 | 000000000 | 00000 | 00000 | 00000 |
14.3 mm ID | ||||||||||||||
22 | 32 | 26 | 4 | 0.016 to 0.034 | 0.015 to 0.028 | -0.3 to 0.3 | H | Steel | Rockwell C61 | DIN 172 | 000000000 | 00000 | 00000 | 00000 |
14.4 mm ID | ||||||||||||||
22 | 32 | 26 | 4 | 0.016 to 0.034 | 0.015 to 0.028 | -0.3 to 0.3 | H | Steel | Rockwell C61 | DIN 172 | 000000000 | 00000 | 00000 | 00000 |
14.5 mm ID | ||||||||||||||
22 | 32 | 26 | 4 | 0.016 to 0.034 | 0.015 to 0.028 | -0.3 to 0.3 | H | Steel | Rockwell C61 | DIN 172 | 000000000 | 00000 | 00000 | 00000 |
14.6 mm ID | ||||||||||||||
22 | 32 | 26 | 4 | 0.016 to 0.034 | 0.015 to 0.028 | -0.3 to 0.3 | H | Steel | Rockwell C61 | DIN 172 | 000000000 | 00000 | 00000 | 00000 |
14.7 mm ID | ||||||||||||||
22 | 32 | 26 | 4 | 0.016 to 0.034 | 0.015 to 0.028 | -0.3 to 0.3 | H | Steel | Rockwell C61 | DIN 172 | 000000000 | 00000 | 00000 | 00000 |
14.8 mm ID | ||||||||||||||
22 | 32 | 26 | 4 | 0.016 to 0.034 | 0.015 to 0.028 | -0.3 to 0.3 | H | Steel | Rockwell C61 | DIN 172 | 000000000 | 00000 | 00000 | 00000 |
14.9 mm ID | ||||||||||||||
22 | 32 | 26 | 4 | 0.016 to 0.034 | 0.015 to 0.028 | -0.3 to 0.3 | H | Steel | Rockwell C61 | DIN 172 | 000000000 | 00000 | 00000 | 00000 |
15 mm ID | ||||||||||||||
22 | 32 | 26 | 4 | 0.016 to 0.034 | 0.015 to 0.028 | -0.3 to 0.3 | H | Steel | Rockwell C61 | DIN 172 | 000000000 | 00000 | 00000 | 00000 |
15.5 mm ID | ||||||||||||||
26 | 32 | 30 | 4 | 0.016 to 0.034 | 0.015 to 0.028 | -0.3 to 0.3 | H | Steel | Rockwell C61 | DIN 172 | 000000000 | 00000 | 00000 | 00000 |
16 mm ID | ||||||||||||||
26 | 32 | 30 | 4 | 0.016 to 0.034 | 0.015 to 0.028 | -0.3 to 0.3 | H | Steel | Rockwell C61 | DIN 172 | 000000000 | 00000 | 00000 | 00000 |
16.5 mm ID | ||||||||||||||
26 | 32 | 30 | 4 | 0.016 to 0.034 | 0.015 to 0.028 | -0.3 to 0.3 | H | Steel | Rockwell C61 | DIN 172 | 000000000 | 00000 | 00000 | 00000 |
17 mm ID | ||||||||||||||
26 | 32 | 30 | 4 | 0.016 to 0.034 | 0.015 to 0.028 | -0.3 to 0.3 | H | Steel | Rockwell C61 | DIN 172 | 000000000 | 00000 | 00000 | 00000 |
17.5 mm ID | ||||||||||||||
26 | 32 | 30 | 4 | 0.016 to 0.034 | 0.015 to 0.028 | -0.3 to 0.3 | H | Steel | Rockwell C61 | DIN 172 | 000000000 | 00000 | 00000 | 00000 |
18 mm ID | ||||||||||||||
26 | 32 | 30 | 4 | 0.016 to 0.034 | 0.015 to 0.028 | -0.3 to 0.3 | H | Steel | Rockwell C61 | DIN 172 | 000000000 | 00000 | 00000 | 00000 |