About Shaft Couplings
More
About Ball and Roller Bearings
More
About Linear Bearings
More
Mounted Bearings with Three-Bolt Flange
Bearings are self-aligning to compensate for shaft misalignment. Seals block out dust and contaminants.
Steel bearings are stronger than stainless steel bearings, but not as corrosion resistant.
For technical drawings and 3-D models, click on a part number.
Overall | Mounting | Radial Load Cap., lbs. | ||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| For Shaft Dia. | Center Ht. | Ht. | Lg. | Wd. | Flange Thick. | Hole Dia. | Hole Ctr.-to-Ctr. Lg. | Hole Ctr.-to-Ctr. Ht. | Dynamic | Static | Max. Speed, rpm | Temp. Range, °F | Each | |
Sealed Steel Ball Bearings with Nickel-Plated Cast Iron Housing—Self Aligning | ||||||||||||||
Shaft Mount Type: Set Screw | ||||||||||||||
| 1 5/8" | 4 1/4" | 6 27/32" | 4 3/16" | 1 31/32" | 23/32" | 7/16" | 2 1/8" | 1 11/16" | 7,650 | 4,750 | 3,000 | 0° to 210° | 0000000 | 000000 |
| 1 11/16" | 4 1/4" | 6 27/32" | 4 3/16" | 1 31/32" | 23/32" | 7/16" | 2 1/8" | 1 11/16" | 7,650 | 4,750 | 3,000 | 0° to 210° | 0000000 | 00000 |
| 1 3/4" | 4 1/4" | 6 27/32" | 4 3/16" | 1 31/32" | 23/32" | 7/16" | 2 1/8" | 1 11/16" | 7,650 | 4,750 | 3,000 | 0° to 210° | 0000000 | 00000 |
Chemical-Resistant Flange-Mounted Linear Sleeve Bearings
The Frelon liner on these bearings allows them to stand up to a wider range of chemicals than other flange-mounted linear sleeve bearings. All are self-aligning to compensate for shaft misalignment and are for use with round end-supported shafts. Note: Not for use with bare aluminum or chrome-plated shafts.
Bearings with 0.0005" shaft clearance are best for precision applications. Bearings with 0.0015" shaft clearance are less likely to bind on your shaft than bearings with 0.0005" shaft clearance.
For technical drawings and 3-D models, click on a part number.
Overall | Mounting Holes | ||||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| For Shaft Dia. | Shaft Clearance | Lg. | Wd. | Ht. | Flange Thick. | Bolt Circle Dia. | OD | Dynamic Load Capacity | Static Load Capacity, lbs. | Temperature Range, ° F | For Shaft Material | No. of | Dia. | Each | |
Self Aligning with 0.5° Misalignment Capability | |||||||||||||||
Frelon-Lined 6061 Aluminum Bearings with 6061 Aluminum Housing | |||||||||||||||
| 3/4" | 0.0005" | 4 3/16" | 2 3/8" | 2 3/8" | 3/8" | 2 15/32" | 1 3/4" | 600 lbs. @ 100 fpm | 5,800 | -400° to 400° | Ceramic-Coated Aluminum, Stainless Steel, Steel | 4 | 3/16" | 000000000 | 0000000 |
| 3/4" | 0.0015" | 4 3/16" | 2 3/8" | 2 3/8" | 3/8" | 2 15/32" | 1 3/4" | 600 lbs. @ 100 fpm | 5,800 | -400° to 400° | Ceramic-Coated Aluminum, Stainless Steel, Steel | 4 | 3/16" | 000000000 | 000000 |
Flange-Mounted Linear Bearing Housings
Slide up to two linear ball or sleeve bearings into these housings and secure them with the included internal retaining rings.
Housings for two bearings give you better running accuracy and alignment than using two separate pillow blocks.
For technical drawings and 3-D models, click on a part number.
Overall | Mounting Holes | |||||||||
|---|---|---|---|---|---|---|---|---|---|---|
| For Bearing OD | For Max. Bearing Lg. | Lg. | Wd. | Ht. | Flange Thick. | OD | No. of | Dia. | Each | |
6061 Aluminum  | ||||||||||
For Two Bearings | ||||||||||
| 1 1/4" | 1 5/8" | 4 3/16" | 2 3/8" | 2 3/8" | 3/8" | 1 3/4" | 4 | 7/32" | 0000000 | 0000000 |
Vibration-Damping Flexible Shaft Couplings
Coupling Shown
Assembled
A flexible tire on these couplings safeguards components on your shafts by reducing vibration and shock.
A complete coupling consists of two hubs, one tire, and two quick-disconnect bushings.
Quick-disconnect bushings are easy to install and remove. Tighten their cap screws to secure them to your shafts. For information on quick-disconnect bushing styles, see Quick-Disconnect (QD) Bushings.
For technical drawings and 3-D models, click on a part number.
Buna-N Rubber Tires | ||||||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
Iron and Steel Hubs | Misalignment Capability | Quick-Disconnect (QD) Bushings | ||||||||||||||
| O'all Lg. | OD | For Motion Type | Each | Max. Speed, rpm | Max. Torque, in.-lbs. | Parallel | Angular | Axial | Temp. Range, °F | Each | Bushing Style | For Shaft Dia. | Each | |||
| 4 3/16" | 7 3/8" | Continuous | 0000000 | 0000000 | 3,600 | 2,200 | 0.125" | 4° | 0.313" | -65° to 180° | 0000000 | 0000000 | SH | 0000000 | 000000 | |