System of Measurement System of Measurement |
|---|
|
For Shaft Diameter For Shaft Diameter |
|---|
|
Housing Type Housing Type |
|---|
 | Flange Mount |
Length Length | Show |
|---|
|
Length Length | Hide |
|---|
For Shaft Material For Shaft Material |
|---|
|
Linear Bearing Component Linear Bearing Component |
|---|
 |  |
| Bearing | Bearing in Housing |
For Shaft Type For Shaft Type |
|---|
 | Round |
Alignment Style Alignment Style |
|---|
|
Housing Material Housing Material |
|---|
|
Bearing Type Bearing Type |
|---|
 | Ball |
With End Seals With End Seals |
|---|
|
Dynamic Load Capacity Dynamic Load Capacity |
|---|
|
Static Load Capacity Static Load Capacity |
|---|
|
Bearing Material Bearing Material |
|---|
|
For Minimum Steel Shaft Hardness For Minimum SteelShaft Hardness |
|---|
|
ID ID |
|---|
|
RoHS (Restriction of Hazardous Substances) RoHS (Restriction ofHazardous Substances) |
|---|
|
For Minimum Stainless Steel Shaft Hardness For Minimum StainlessSteel Shaft Hardness |
|---|
|
DFARS (Defense Acquisition Regulations Supplement) DFARS (Defense AcquisitionRegulations Supplement)  |
|---|
REACH (Registration, Evaluation, Authorization and Restriction of Chemicals) REACH (Registration,Evaluation, Authorization and Restriction of Chemicals) |
|---|
|
About Linear Bearings
More
About Shaft Couplings
More
Linear Ball Bearings
Bearings are for use with round end-supported shafts. To install, slide bearings into a housing (not included). For bearings with retaining ring grooves, secure with two retaining rings (sold individually).
Bearings with end seals keep lubricant in and dust out.
Fixed-alignment bearings are for use where shaft misalignment is unlikely.
For technical drawings and 3-D models, click on a part number.
Bearings | |||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
Load Capacity, lbs. | External Retaining Rings | ||||||||||||
| For Shaft Dia. | Overall Lg. | For Housing ID | Retaining Ring Groove End-to-End Lg. | With End Seals | Dynamic | Static | Min. Temp., °F | Max. Temp., °F | For Shaft Material | Each | Each | ||
Steel Bearings with Steel Balls | |||||||||||||
| 1 1/2" | 5 11/16" | 2.3750" - 2.3762" | 4.82" | Yes | 770 | 1,800 | Not Rated | 176° | Stainless Steel, Steel | 00000000 | 0000000 | 0000000 | 00000 |
Flange-Mounted Linear Ball Bearings
The flanged housing makes these bearings a good solution for vertical linear motion applications. All are for use with round end-supported shafts and have a fixed-alignment design for use where shaft misalignment is unlikely. End seals keep lubricant in and dirt out.
For technical drawings and 3-D models, click on a part number.
Overall | Flange | Load Capacity, lbs. | Mounting Holes | ||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| For Shaft Dia. | Lg. | Wd. | Ht. | Thick. | OD | Bolt Circle Dia. | OD | Dynamic | Static | Temperature Range, ° F | For Shaft Material | No. of | Dia. | Each | |
Steel Bearings with Round Flanged Housing | |||||||||||||||
| 1 1/2" | 5 11/16" | 3 3/4" | 3 3/4" | 1/2" | 3 3/4" | 3 1/16" | 2 3/8" | 770 | 1,800 | -4° to 176° | Stainless Steel, Steel | 4 | 11/32" | 0000000 | 0000000 |
Steel Bearings with Square Flanged Housing | |||||||||||||||
| 1 1/2" | 5 11/16" | 3" | 3" | 1/2" | __ | 3 1/16" | 2 3/8" | 770 | 1,800 | -4° to 176° | Stainless Steel, Steel | 4 | 11/32" | 0000000 | 000000 |
Vibration-Damping Flexible Shaft Couplings
Coupling Shown
Assembled
A flexible tire on these couplings safeguards components on your shafts by reducing vibration and shock.
A complete coupling consists of two hubs, one tire, and two quick-disconnect bushings.
Quick-disconnect bushings are easy to install and remove. Tighten their cap screws to secure them to your shafts. For information on quick-disconnect bushing styles, see Quick-Disconnect (QD) Bushings.
For technical drawings and 3-D models, click on a part number.
Buna-N Rubber Tires | ||||||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
Iron and Steel Hubs | Misalignment Capability | Quick-Disconnect (QD) Bushings | ||||||||||||||
| O'all Lg. | OD | For Motion Type | Each | Max. Speed, rpm | Max. Torque, in.-lbs. | Parallel | Angular | Axial | Temp. Range, °F | Each | Bushing Style | For Shaft Dia. | Each | |||
| 5 11/16" | 9 1/4" | Continuous | 0000000 | 0000000 | 2,800 | 4,350 | 0.125" | 4° | 0.313" | -65° to 180° | 0000000 | 0000000 | SK | 0000000 | 000000 | |