Mounted Bearing Type Mounted Bearing Type |
---|
![]() | Four-Bolt Flange Mount |
System of Measurement System of Measurement |
---|
|
For Shaft Diameter For Shaft Diameter |
---|
|
Housing Material Housing Material |
---|
|
Bearing Type Bearing Type |
---|
![]() | Ball |
Alignment Style Alignment Style |
---|
|
ID ID |
---|
|
Maximum Temperature Maximum Temperature |
---|
|
Mounting Hole Center-to-Center Mounting HoleCenter-to-Center |
---|
|
For Load Direction For Load Direction |
---|
![]() | Radial |
Shaft Mount Type Shaft Mount Type |
---|
|
Length Length | Show |
---|
|
Length Length | Hide |
---|

Dynamic Radial Load Capacity Dynamic Radial Load Capacity |
---|
|
Seal Type Seal Type |
---|
|
For Shaft Type For Shaft Type |
---|
![]() | Round |
Lubrication Lubrication |
---|
|
Static Radial Load Capacity Static Radial Load Capacity |
---|
|
Bearing Material Bearing Material |
---|
|
REACH (Registration, Evaluation, Authorization and Restriction of Chemicals) REACH (Registration,Evaluation, Authorization and Restriction of Chemicals) |
---|
|
RoHS (Restriction of Hazardous Substances) RoHS (Restriction ofHazardous Substances) |
---|
|
About Ball and Roller Bearings
More
Mounted Ball Bearings with Four-Bolt Flange
Bearings are self-aligning to compensate for shaft misalignment. Seals block out dust and contaminants.
Set screw bearings secure to shafts as you tighten their screw. They don’t need a collar, but the screw leaves some marring on shafts. Use them in applications where shafts rotate in both directions.
For technical drawings and 3-D models, click on a part number.

Overall | Mounting | Radial Load Cap., lbs. | ||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
For Shaft Dia. | Ht. | Lg. | Wd. | Flange Thick. | Hole Dia. | Hole Ctr.-to-Ctr. | Dynamic | Static | Max. Speed, rpm | Temp. Range, °F | Alignment Style | Lubrication | Each | |
Sealed Steel Bearings with Cast Iron Housing | ||||||||||||||
Shaft Mount Type: Set Screw | ||||||||||||||
2" | 6 3/8" | 6 3/8" | 2 35/64" | 11/16" | 11/16" | 5 1/8" | 9,800 | 6,500 | 3,600 | -20° to 210° | Self Aligning | Lubricated | 0000000 | 0000000 |
Permanently Lubricated Washdown Mounted Ball Bearings with Four-Bolt Flange

Made to withstand frequent washdowns, these bearings are permanently lubricated, which means you’ll never have to add lubricant. Use them in hard-to-reach areas in food, beverage, pharmaceutical, and chemical plants. With a 316 stainless steel housing, these bearings won’t rust from salt water, chlorine, or chemicals. All are lubricated with NSF registered H1 grease, which is certified for incidental contact with food.
Concentric-lock bearings have a collar that centers and secures the shaft in the bearing bore. To install, tighten the single screw on the collar around its inner ring on your shaft. These bearings have a secure grip on the shaft that reduces vibration and noise.
For technical drawings and 3-D models, click on a part number.
Overall | Mounting | Radial Load Capacity, lbs. | ||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
For Shaft Dia. | Height | Length | Width | Flange Thick. | Hole Dia. | Hole Ctr.-to-Ctr. | Dynamic | Static | Max. Speed, rpm | Temp. Range, °F | Alignment Style | Environmental Rating | Each | |
Sealed Steel Bearings with 316 Stainless Steel Housing | ||||||||||||||
Shaft Mount Type: Concentric Lock | ||||||||||||||
2" | 2 5/16" | 6 3/8" | 3 13/32" | 13/16" | 5/8" | 5 1/8" | 9,750 | 4,460 | 1,350 | -20° to 220° | Self Aligning | IP69K | 0000000 | 0000000 |
High-Temperature Mounted Ball Bearings with Four-Bolt Flange

Synthetic grease enables these bearings to operate in temperatures up to 400° F—nearly double the maximum temperature of standard mounted ball bearings with four-bolt flange. They are self-aligning to compensate for shaft misalignment. Seals block out dust and contaminants.
For technical drawings and 3-D models, click on a part number.
Overall | Mounting | Radial Load Cap., lbs. | ||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
For Shaft Dia. | Ht. | Lg. | Wd. | Flange Thick. | Hole Dia. | Hole Ctr.-to-Ctr. | Dynamic | Static | Max. Speed, rpm | Temp. Range, °F | Alignment Style | Lubrication | Each | |
Sealed Steel Bearings with Cast Iron Housing | ||||||||||||||
Shaft Mount Type: Set Screw | ||||||||||||||
2" | 6 3/8" | 6 3/8" | 2 5/16" | 13/16" | 21/32" | 5 1/8" | 9,750 | 6,600 | 1,400 | -20° to 400° | Self Aligning | Lubricated | 0000000 | 0000000 |