Seal Type Seal Type |
|---|
|
For Load Direction For Load Direction |
|---|
 | Radial |
 | Combined Radial and Thrust |
Mounted Bearing Type Mounted Bearing Type |
|---|
 |  |
| Base Mount | Four-Bolt Flange Mount |
Shaft Mount Type Shaft Mount Type |
|---|
|
Length Length | Show |
|---|
|
Length Length | Hide |
|---|
Dynamic Radial Load Capacity Dynamic RadialLoad Capacity |
|---|
|
Alignment Style Alignment Style |
|---|
|
Static Radial Load Capacity Static Radial Load Capacity |
|---|
|
Housing Material Housing Material |
|---|
|
Flange Thickness Flange Thickness |
|---|
|
Misalignment Capability Misalignment Capability |
|---|
|
DFARS (Defense Acquisition Regulations Supplement) DFARS (Defense AcquisitionRegulations Supplement) |
|---|
Grease Fitting Thread Type Grease Fitting Thread Type |
|---|
|
Lubricant Lubricant |
|---|
|
Mounted Roller Bearings
Roller bearings have a thinner profile and larger contact area than ball bearings, making them stronger and more space-efficient than ball bearings.
Sealed bearings block out dust and contaminants.
For technical drawings and 3-D models, click on a part number.
Overall | Mounting | Radial Load Cap., lbs. | ||||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| For Shaft Dia. | Center Ht. | Ht. | Lg. | Wd. | Hole Lg. | Hole Wd. | Hole Ctr.-to-Ctr. | Dynamic | Static | Dynamic Thrust Load Cap., lbs. | Max. Speed, rpm | Temp. Range, °F | Alignment Style | Lubrication | Each | |
Steel Bearings with Cast Iron Housing—Shaft Mount Type: Set Screw | ||||||||||||||||
| 1 3/8" | 1 7/8" | 3 3/4" | 7 3/8" | 3" | 3/4" | 5/8" | 5 3/4" | 6,100 | 26,000 | 2,550 | 3,800 | -60° to 250° | Fixed Alignment | Lubricated | 0000000 | 0000000 |
| 35mm | 1 7/8" | 3 3/4" | 7 3/8" | 3" | 3/4" | 5/8" | 5 3/4" | 6,100 | 26,000 | 2,550 | 3,800 | -60° to 250° | Fixed Alignment | Lubricated | 0000000 | 000000 |
Mounted Ball Bearings with Four-Bolt Flange
Bearings are self-aligning to compensate for shaft misalignment. Seals block out dust and contaminants.
Set screw bearings secure to shafts as you tighten their screw. They don’t need a collar, but the screw leaves some marring on shafts. Use them in applications where shafts rotate in both directions.
For technical drawings and 3-D models, click on a part number.
Overall | Mounting | Radial Load Cap., lbs. | ||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| For Shaft Dia. | Ht. | Lg. | Wd. | Flange Thick. | Hole Dia. | Hole Ctr.-to-Ctr. | Dynamic | Static | Max. Speed, rpm | Temp. Range, °F | Alignment Style | Lubrication | Each | |
Sealed Steel Bearings with Cast Iron Housing | ||||||||||||||
Shaft Mount Type: Set Screw | ||||||||||||||
| 2 1/2" | 7 3/8" | 7 3/8" | 3 3/16" | 7/8" | 11/16" | 5 7/8" | 12,800 | 9,000 | 3,000 | -20° to 210° | Self Aligning | Lubricated | 00000000 | 0000000 |
Speed Reducers for Roller Conveyors
Also known as pallet brakes, these mount underneath rollers on a gravity conveyor and create friction on the rollers to control the conveyor's speed. Speed reducers have an internal brake that gradually engages as the speed of the rollers increases. For best results, the spacing of the reducers should be equal to the length of the material you're conveying.
For technical drawings and 3-D models, click on a part number.
O'all | ||||||||||
|---|---|---|---|---|---|---|---|---|---|---|
| Cap., lbs. | For Roller Dia. | For Roller Spacing | Lg. | Wd. | Ht. | Material | Wheel Material | Mounting Hardware Included | Each | |
| 25-500 | 1 3/8", 1.9", 2 1/2" | 2"-4" | 7 3/8" | 4" | 4 3/4" | Steel | Rubber-Coated Plastic | Yes | 0000000 | 000000 |
| 175-1,800 | 1 3/8", 1.9", 2 1/2" | 2"-4" | 7 3/8" | 4" | 4 3/4" | Steel | Rubber-Coated Plastic | Yes | 0000000 | 00000 |
| 500-2,500 | 1 3/8", 1.9", 2 1/2" | 2"-4" | 7 3/8" | 4" | 4 3/4" | Steel | Rubber-Coated Plastic | Yes | 0000000 | 00000 |