System of Measurement System of Measurement |
---|
|
For Shaft Diameter For Shaft Diameter |
---|
|
Mounted Bearing Type Mounted Bearing Type |
---|
![]() | Four-Bolt Flange Mount |
Housing Material Housing Material |
---|
|
ID ID |
---|
|
Length Length | Show |
---|
|
Length Length | Hide |
---|

Shaft Mount Type Shaft Mount Type |
---|
|
Mounting Hole Center-to-Center Mounting HoleCenter-to-Center |
---|
|
Bearing Type Bearing Type |
---|
![]() | Ball |
For Load Direction For Load Direction |
---|
![]() | Radial |
Lubrication Lubrication |
---|
|
Alignment Style Alignment Style |
---|
|
For Shaft Type For Shaft Type |
---|
![]() | Round |
REACH (Registration, Evaluation, Authorization and Restriction of Chemicals) REACH (Registration,Evaluation, Authorization and Restriction of Chemicals) |
---|
|
ABEC Rating ABEC Rating |
---|
|
Lubricant Lubricant |
---|
|
Misalignment Capability Misalignment Capability |
---|
|
Number of Set Screws Included Number of SetScrews Included |
---|
|
RoHS (Restriction of Hazardous Substances) RoHS (Restriction ofHazardous Substances) |
---|
|
About Ball and Roller Bearings
More
Mounted Ball Bearings with Four-Bolt Flange
Bearings are self-aligning to compensate for shaft misalignment. Seals block out dust and contaminants.
Set screw bearings secure to shafts as you tighten their screw. They don’t need a collar, but the screw leaves some marring on shafts. Use them in applications where shafts rotate in both directions.
For technical drawings and 3-D models, click on a part number.

Overall | Mounting | Radial Load Cap., lbs. | ||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
For Shaft Dia. | Ht. | Lg. | Wd. | Flange Thick. | Hole Dia. | Hole Ctr.-to-Ctr. | Dynamic | Static | Max. Speed, rpm | Temp. Range, °F | Alignment Style | Lubrication | Each | |
Sealed Steel Bearings with Cast Iron Housing | ||||||||||||||
Shaft Mount Type: Set Screw | ||||||||||||||
20mm | 85.7mm | 85.7mm | 32.5mm | 11.1mm | 10.3mm | 63.5mm | 2,600 | 1,400 | 7,300 | -20° to 220° | Self Aligning | Lubricated | 000000 | 0000000 |
Permanently Lubricated Washdown Mounted Ball Bearings with Four-Bolt Flange

Made to withstand frequent washdowns, these bearings are permanently lubricated, which means you’ll never have to add lubricant. Use them in hard-to-reach areas in food, beverage, pharmaceutical, and chemical plants. With a 316 stainless steel housing, these bearings won’t rust from salt water, chlorine, or chemicals. All are lubricated with NSF registered H1 grease, which is certified for incidental contact with food.
Set-screw bearings secure to shafts as you tighten their screw. They don’t need a collar; however, the screws leave some marring on the shaft.
For technical drawings and 3-D models, click on a part number.
Overall | Mounting | Radial Load Capacity, lbs. | ||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
For Shaft Dia. | Height | Length | Width | Flange Thick. | Hole Dia. | Hole Ctr.-to-Ctr. | Dynamic | Static | Max. Speed, rpm | Temp. Range, °F | Alignment Style | Environmental Rating | Each | |
Sealed Steel Bearings with 316 Stainless Steel Housing | ||||||||||||||
Shaft Mount Type: Set Screw | ||||||||||||||
20mm | 32.5mm | 85.7mm | 58.3mm | 11.1mm | 9.5mm | 63.5mm | 2,610 | 6,600 | 3,100 | -20° to 220° | Self Aligning | IP69K | 0000000 | 0000000 |