About Plain Bearings
More
Oil-Embedded Sleeve Bearings
Startup friction causes these porous bronze bearings to release a thin layer of oil on the bearing’s surface. They are also known as Oilite® bearings.
To Order: For made-to-order bearings, please specify ID and OD (in 0.0001" or 0.001 mm increments) and length (in 0.001" or 0.01 mm increments). The difference between the ID and OD must be at least 0.0625" for inch sizes or 2 mm for metric.
| ID | OD | Lg. | Lubrication | Lubricant | Temperature Range, °F | Each | |
| 0.125"-0.3124" | 0.1875"-0.5625" | 0.063"-0.625" | Lubricated | SAE 30 Oil | -35° to 300° | 00000000 | 0000000 |
| 0.3125"-0.7499" | 0.375"-0.9375" | 0.063"-1.5" | Lubricated | SAE 30 Oil | -35° to 300° | 00000000 | 000000 |
| 0.75"-1.2499" | 0.8125"-1.5" | 0.063"-2.75" | Lubricated | SAE 30 Oil | -35° to 300° | 00000000 | 000000 |
| 1.25"-1.9999" | 1.3125"-2.25" | 0.063"-3" | Lubricated | SAE 30 Oil | -35° to 300° | 00000000 | 000000 |
| 2"-2.9375" | 2.0625"-3" | 0.063"-4" | Lubricated | SAE 30 Oil | -35° to 300° | 00000000 | 000000 |
To Order: For made-to-order bearings, please specify ID and OD (in 0.0001" or 0.001 mm increments) and length (in 0.001" or 0.01 mm increments). The difference between the ID and OD must be at least 0.0625" for inch sizes or 2 mm for metric.
| ID | OD | Lg. | Lubrication | Lubricant | Temperature Range, °F | Each | |
| 3mm-7.999mm | 5mm-14mm | 2mm-16mm | Lubricated | SAE 30 Oil | -35° to 300° | 0000000 | 0000000 |
| 8mm-18.999mm | 10mm-24mm | 2mm-38mm | Lubricated | SAE 30 Oil | -35° to 300° | 0000000 | 000000 |
| 19mm-31.999mm | 21mm-38mm | 2mm-70mm | Lubricated | SAE 30 Oil | -35° to 300° | 0000000 | 000000 |
| 32mm-50.999mm | 34mm-57mm | 2mm-75mm | Lubricated | SAE 30 Oil | -35° to 300° | 0000000 | 000000 |
| 51mm-65mm | 53mm-75mm | 2mm-100mm | Lubricated | SAE 30 Oil | -35° to 300° | 0000000 | 000000 |
High-Load Oil-Embedded Sleeve Bearings
Increased iron content makes these bearings stronger and more resistant to shock loads than standard oil-embedded bearings; however they operate at lower speeds. Startup friction causes them to release a thin layer of oil on the bearing’s surface. Color is silver because of the iron. These bearings are also magnetic due to the high iron content.
863 iron-copper bearings are also known as Super Oilite® bearings.
Note: Dynamic load capacity is the maximum load a bearing can withstand at a given shaft speed. If your application’s load and speed requirements are below the values listed, the bearing will work.
To Order: For made-to-order bearings, please specify ID and OD (in 0.0001" increments) and length (in 0.001" increments). The difference between the ID and OD must be at least 0.0625".
| ID | OD | Lg. | Lubrication | Lubricant | Temperature Range, °F | Each | |
| 0.125"-0.3124" | 0.1875"-0.5625" | 0.063"-0.625" | Lubricated | SAE 90 Oil | -15° to 300° | 00000000 | 0000000 |
| 0.3125"-0.7499" | 0.375"-0.9375" | 0.063"-1.5" | Lubricated | SAE 90 Oil | -15° to 300° | 00000000 | 000000 |
| 0.75"-1.2499" | 0.8125"-1.5" | 0.063"-2.75" | Lubricated | SAE 90 Oil | -15° to 300° | 00000000 | 000000 |
| 1.25"-1.9999" | 1.3125"-2.25" | 0.063"-3" | Lubricated | SAE 90 Oil | -15° to 300° | 00000000 | 000000 |
| 2"-2.9375" | 2.0625"-3" | 0.063"-4" | Lubricated | SAE 90 Oil | -15° to 300° | 00000000 | 000000 |
Ultra-Low-Friction Oil-Embedded Sleeve Bearings
For applications with frequent starts and stops, the oil in these bearings contains particles of slippery PTFE that lubricate the bearing during startup.
To Order: For made-to-order bearings, please specify ID and OD (in 0.0001" increments) and length (in 0.001" increments). The difference between the ID and OD must be at least 0.0625".
| ID | OD | Lg. | Lubrication | Lubricant | Temperature Range, °F | Each | |
| 0.125"-0.3124" | 0.1875"-0.5625" | 0.063"-0.625" | Lubricated | SAE 20 Oil with PTFE | -40° to 300° | 0000000 | 0000000 |
| 0.3125"-0.7499" | 0.375"-0.9375" | 0.063"-1.5" | Lubricated | SAE 20 Oil with PTFE | -40° to 300° | 0000000 | 000000 |
| 0.75"-1.2499" | 0.8125"-1.5" | 0.063"-2.75" | Lubricated | SAE 20 Oil with PTFE | -40° to 300° | 0000000 | 000000 |
| 1.25"-1.9999" | 1.3125"-2.25" | 0.063"-3" | Lubricated | SAE 20 Oil with PTFE | -40° to 300° | 0000000 | 000000 |
| 2"-2.9375" | 2.0625"-3" | 0.063"-4" | Lubricated | SAE 20 Oil with PTFE | -40° to 300° | 0000000 | 000000 |
Food Industry Oil-Embedded Sleeve Bearings
The oil in these bearings is suitable for incidental contact with food. Startup friction produces a thin layer of oil on the bearing’s surface.
Note: Dynamic load capacity is the maximum load a bearing can withstand at a given shaft speed. If your application’s load and speed requirements are below the values listed, the bearing will work.
To Order: For made-to-order bearings, please specify ID and OD (in 0.0001" increments) and length (in 0.001" increments). The difference between the ID and OD must be at least 0.0625".
| ID | OD | Lg. | Lubrication | Lubricant | Temperature Range, °F | Each | |
| 0.125"-0.3124" | 0.1875"- 0.5625" | 0.063"-0.625" | Lubricated | SAE 20 Oil | -75° to 300° | 0000000 | 0000000 |
| 0.3125"-0.7499" | 0.375"- 0.9375" | 0.063"-1.5" | Lubricated | SAE 20 Oil | -75° to 300° | 0000000 | 000000 |
| 0.75"-1.2499" | 0.8125"- 1.5" | 0.063"-2.75" | Lubricated | SAE 20 Oil | -75° to 300° | 0000000 | 000000 |
| 1.25"-1.9999" | 1.3125"- 2.25" | 0.063"-3" | Lubricated | SAE 20 Oil | -75° to 300° | 0000000 | 000000 |
| 2"-2.9375" | 2.0625"- 3" | 0.063"-4" | Lubricated | SAE 20 Oil | -75° to 300° | 0000000 | 000000 |
Made-to-Order Press-Fit Drill Bushings
Mount flush with jig plates for precise drilling. These bushings can also be used as spacers, shims, and machinery bushings.
To Order: Specify ID, OD, and length from the ranges listed. The difference between the ID and OD must be at least 0.07".
For technical drawings and 3-D models, click on a part number.
Each | ||||||||||
|---|---|---|---|---|---|---|---|---|---|---|
| Choose an ID | Choose an OD | Choose a Length | Length Tolerance | Drill Bushing Type | Material | Hardness | 1-5 | 6-11 | 12-Up | |
| 0.0135" to 2.2656" in 0.0001" increments | 0.1562" to 2.7500" in 0.0001" increments | 0.125" to 3" in 0.0625" increments | -0.015" to 0.015" | P | Steel | Rockwell C61 | 00000000 | 000000 | 000000 | 000000 |