Ball Bearing Type Ball Bearing Type |
---|
![]() | Flanged |
Inner Ring Type Inner Ring Type |
---|
![]() | Standard |
Shaft Mount Type Shaft Mount Type |
---|
|
For Load Direction For Load Direction |
---|
![]() | Radial |
![]() | Combined Radial and Thrust |
![]() | Thrust |
Bearing Trade Number Bearing Trade Number |
---|

|
Dynamic Radial Load Capacity Dynamic Radial Load Capacity |
---|
|
|
Lubrication Lubrication |
---|
|
Static Radial Load Capacity Static Radial Load Capacity |
---|
|
For Shaft Type For Shaft Type |
---|
![]() | Round |
Cage Width Cage Width |
---|
|
Maximum Speed Maximum Speed | Show |
---|
|
Maximum Speed Maximum Speed | Hide |
---|
REACH (Registration, Evaluation, Authorization and Restriction of Chemicals) REACH (Registration,Evaluation, Authorization and Restriction of Chemicals) |
---|
|
RoHS (Restriction of Hazardous Substances) RoHS (Restriction ofHazardous Substances) |
---|
|
About Ball and Roller Bearings
More
About Track Rollers
Also known as cam followers, track rollers have a thick outer roller that runs directly on a flat surface.
More
Lubrication-Free Plastic Flanged Ball Bearings


Install these acetal bearings in caustic environments and where lubrication can’t be used. They have good all-around corrosion and chemical resistance. The flange ensures proper positioning inside a tube or housing.
For technical drawings and 3-D models, click on a part number.
Flange | Radial Load Cap., lbs. | |||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
Bearing Trade Number | For Shaft Dia. | For Housing ID | Wd. | OD | Thick. | Ring Material | Dynamic | Static | Max. Speed, rpm | Lubrication | Temp. Range, °F | ABEC Rating | Each | |
Shielded | ||||||||||||||
6001 | 12mm | 28mm | 9mm | 30mm | 2mm | Acetal Plastic | 30 | 25 | 1,700 | Not Required | -40° to 175° | Not Rated | 00000000 | 000000 |
6001 | 12mm | 35mm | 9mm | 38mm | 2mm | Acetal Plastic | 30 | 25 | 1,700 | Not Required | -40° to 175° | Not Rated | 00000000 | 00000 |
Tapered-Roller Bearings


Found anywhere from machine tool spindles to conveyor rollers, these bearings have a two-piece design that allows for adjustment.
For technical drawings and 3-D models, click on a part number.
Radial Load Cap., lbs. | Thrust Load Cap., lbs. | |||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|
For Shaft Dia. | For Housing ID | Wd. | Bearing Trade Number | Dynamic | Static | Dynamic | Static | Max. Speed, rpm | Lubrication | Temp. Range, °F | Each | |
Steel Ring | ||||||||||||
Open | ||||||||||||
2 1/2" | 4 1/4" | 3/4" | 29585/29520 | 7,600 | 36,300 | 5,950 | 48,400 | 1,700 | Required | -60° to 200° | 00000000 | 0000000 |
Shaft-Mount V-Groove Track Rollers


Also known as yoke-style cam followers, these rollers have more mounting flexibility than threaded track rollers. They're typically mounted onto a shaft or clevis rod end. Rollers are for use with Angle Rails for V-Groove Track Rollers. They handle radial and thrust (top and side) loads and work well in dirty environments because debris falls off the angled rail. All rollers are permanently lubricated.
Sealed rollers block out dust and other contaminants better than shielded rollers, but they hold more heat. Their seals also help retain lubricant.
For technical drawings and 3-D models, click on a part number.
Roller | Groove | Radial Load Cap., lbs. | ||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
Dia. | Wd. | For Shaft Dia. | Overall Wd. | Wd. | Dp. | Max. Speed, rpm | Static | Dynamic | Static Thrust Load Cap., lbs. | Max. Temp., °F | Bearing Type | Features | Each | |
440C Stainless Steel V-Groove Rollers with Seal | ||||||||||||||
2 3/8" | 3/4" | 15mm | 3/4" | 3/8" | 3/16" | 1,700 | 2,100 | 2,100 | 890 | 210° | Ball | Single Sealed and Shielded | 0000000 | 0000000 |
440C Stainless Steel V-Groove Rollers without Seal | ||||||||||||||
2 3/8" | 3/4" | 15mm | 3/4" | 3/8" | 3/16" | 1,700 | 1,800 | 1,800 | 740 | 500° | Ball | Shielded | 0000000 | 000000 |
Threaded V-Groove Track Rollers

Thread the stud directly into a component or secure with a nut for through-hole mounting. Rollers are for use with Angle Rails for V-Groove Track Rollers. They handle radial and thrust (top and side) loads and work well in dirty environments because debris falls off the angled rail. Also known as cam followers, track rollers support loads while guiding and positioning work. All rollers are permanently lubricated.
440C stainless steel rollers offer better corrosion resistance than steel rollers.
Rollers with a seal block out dust and other contaminants better than shielded rollers, but they hold more heat. Their seal also helps retain lubricant.
For technical drawings and 3-D models, click on a part number.

Roller, mm | Stud, mm | Thread | Groove, mm | Radial Load Cap., lbs. | |||||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
Dia. | Wd. | Dia. | Lg. | Size | Pitch, mm | Lg., mm | Shoulder Lg., mm | Hex Shoulder Wd., mm | Wd. | Dp. | Max. Speed, rpm | Static | Dynamic | Static Thrust Load Cap., lbs. | Max. Temp., °F | Bearing Type | Includes | Each | |
440C Stainless Steel V-Groove Rollers with Seal | |||||||||||||||||||
60 | 19 | 16 | 40 | M16 | 2 | 24 | 3.1 | 22.2 | 9 | 5 | 1,700 | 2,100 | 2,100 | 900 | 210° | Ball | Mounting Hardware | 0000000 | 0000000 |
Threaded V-Groove Track Rollers with Adjustable Shoulder

Also known as eccentric track rollers, the shoulder adjusts up or down to align to your track, enabling uniform alignment among rollers in a system. Rollers are for use with Angle Rails for V-Groove Track Rollers. They handle radial and thrust (top and side) loads and work well in dirty environments because debris falls off the angled rail. Secure the stud with a nut for through-hole mounting. All rollers are permanently lubricated.
Rollers with a seal block out dust and other contaminants better than shielded rollers, but they hold more heat. Their seal also helps retain lubricant.
For technical drawings and 3-D models, click on a part number.

Roller, mm | Stud, mm | Thread | Groove, mm | Radial Load Cap., lbs. | |||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
Dia. | Wd. | Dia. | Lg. | Size | Pitch, mm | Lg., mm | Shoulder Lg., mm | Hex Shoulder Wd., mm | Wd. | Dp. | Max. Speed, rpm | Static | Dynamic | Static Thrust Load Cap., lbs. | Max. Temp., °F | Each | |
Steel V-Groove Rollers with Seal | |||||||||||||||||
60 | 19 | 12 | 19 | M12 | 1.75 | 14 | 6.8 | 22.23 | 9 | 5 | 1,700 | 2,100 | 2,100 | 900 | 210° | 0000000 | 000000 |