For Load Direction For Load Direction |
---|
![]() | Radial |
![]() | Combined Radial and Thrust |
![]() | Thrust |
Roller Style Roller Style |
---|
![]() | ![]() |
Threaded Stud | Shaft Mount |
Roller Material Roller Material |
---|
|
For Shaft Type For Shaft Type |
---|
![]() | Round |
Maximum Temperature Maximum Temperature |
---|
|
Lubrication Lubrication |
---|
|
Dynamic Radial Load Capacity Dynamic Radial Load Capacity |
---|
|
|
Maximum Speed Maximum Speed | Show |
---|
|
Maximum Speed Maximum Speed | Hide |
---|
RoHS (Restriction of Hazardous Substances) RoHS (Restriction ofHazardous Substances) |
---|
|
REACH (Registration, Evaluation, Authorization and Restriction of Chemicals) REACH (Registration,Evaluation, Authorization and Restriction of Chemicals) |
---|
|
About Ball and Roller Bearings
More
About Track Rollers
Also known as cam followers, track rollers have a thick outer roller that runs directly on a flat surface.
More
Lubrication-Free Plastic Flanged Ball Bearings


Install these acetal bearings in caustic environments and where lubrication can’t be used. They have good all-around corrosion and chemical resistance. The flange ensures proper positioning inside a tube or housing.
For technical drawings and 3-D models, click on a part number.
Flange | Radial Load Cap., lbs. | |||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
Bearing Trade Number | For Shaft Dia. | For Housing ID | Wd. | OD | Thick. | Ring Material | Dynamic | Static | Max. Speed, rpm | Lubrication | Temp. Range, °F | ABEC Rating | Each | |
Shielded | ||||||||||||||
608 | 8mm | 28mm | 7mm | 30mm | 1.5mm | Acetal Plastic | 20 | 15 | 2,200 | Not Required | -40° to 175° | Not Rated | 00000000 | 000000 |
Thrust Ball Bearings


Steel balls and washers allow these bearings to handle higher loads than bearings with stainless steel components. With an open design, they dissipate heat more efficiently than one-piece thrust ball bearings.
Bearings with steel cage and with bronze cage handle higher loads and speeds than bearings with a plastic cage.
For technical drawings and 3-D models, click on a part number.
Thrust Load Cap., lbs. | ||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|
For Shaft Dia. | OD | Thick. | Cage Material | Washer Material | Dynamic | Static | Max. Speed, rpm | Lubrication | Temp. Range, °F | Includes | Each | |
Open | ||||||||||||
120mm | 155mm | 25mm | Steel | Steel | 20,000 | 69,600 | 2,200 | Required | -40° to 250° | Two Washers | 00000000 | 0000000 |
One-Piece Thrust Ball Bearings

In addition to handling higher loads than three-piece ball bearings, one-piece bearings are easier to handle. They have an outer band that holds the bearing together and acts as a shield against dust and other contaminants.
For technical drawings and 3-D models, click on a part number.
Thrust Load Cap., lbs. | |||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|
For Shaft Dia. | OD | Thick. | Ring Material | Dynamic | Static | Max. Speed, rpm | Lubrication | Temp. Range, °F | Features | Each | |
Shielded | |||||||||||
1 7/8" | 3 7/32" | 13/16" | Steel | 10,800 | 27,500 | 2,200 | Required | -40° to 250° | Lubrication Hole | 00000000 | 000000 |
Tapered-Roller Bearings


Found anywhere from machine tool spindles to conveyor rollers, these bearings have a two-piece design that allows for adjustment.
For technical drawings and 3-D models, click on a part number.
Radial Load Cap., lbs. | Thrust Load Cap., lbs. | |||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|
For Shaft Dia. | For Housing ID | Wd. | Bearing Trade Number | Dynamic | Static | Dynamic | Static | Max. Speed, rpm | Lubrication | Temp. Range, °F | Each | |
Steel Ring | ||||||||||||
Open | ||||||||||||
50mm | 80mm | 19mm | 33010 | 4,650 | 25,200 | 2,500 | 23,300 | 2,200 | Required | -60° to 200° | 0000000 | 0000000 |
High-Temperature Mounted Ball Bearings

Synthetic grease enables these bearings to operate in temperatures up to 400° F—nearly double the temperature of standard mounted ball bearings. Bearings are self-aligning to compensate for shaft misalignment. Seals block out dust and contaminants.
For technical drawings and 3-D models, click on a part number.
Overall | Mounting | Radial Load Cap., lbs. | |||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
For Shaft Dia. | Center Ht. | Ht. | Lg. | Wd. | Hole Lg. | Hole Wd. | Hole Ctr.-to-Ctr. | Dynamic | Static | Max. Speed, rpm | Temp. Range, °F | Alignment Style | Lubrication | Each | |
Sealed Steel Bearings with Cast Iron Housing | |||||||||||||||
Shaft Mount Type: Set Screw | |||||||||||||||
1 1/4" | 1 7/8" | 4 1/8" | 6 9/16" | 2" | 13/16" | 9/16" | 5" | 5,750 | 3,450 | 2,200 | -20° to 400° | Self Aligning | Lubricated | 0000000 | 0000000 |
High-Temperature Mounted Ball Bearings with Two-Bolt Flange

Synthetic grease enables these bearings to operate in temperatures up to 400° F—nearly double the maximum temperature of standard mounted ball bearings with two-bolt flange. Bearings are self-aligning to compensate for shaft misalignment. Seals block out dust and contaminants.
For technical drawings and 3-D models, click on a part number.
Overall | Mounting | Radial Load Cap., lbs. | ||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
For Shaft Dia. | Ht. | Lg. | Wd. | Flange Thick. | Hole Dia. | Hole Ctr.-to-Ctr. | Dynamic | Static | Max. Speed, rpm | Temp. Range, °F | Alignment Style | Lubrication | Each | |
Sealed Steel Bearings with Cast Iron Housing | ||||||||||||||
Shaft Mount Type: Set Screw | ||||||||||||||
1 1/4" | 3 3/4" | 6 1/8" | 1 3/4" | 9/16" | 17/32" | 5 1/8" | 5,750 | 3,450 | 2,200 | -20° to 400° | Self Aligning | Lubricated | 0000000 | 0000000 |
High-Temperature Mounted Ball Bearings with Four-Bolt Flange

Synthetic grease enables these bearings to operate in temperatures up to 400° F—nearly double the maximum temperature of standard mounted ball bearings with four-bolt flange. They are self-aligning to compensate for shaft misalignment. Seals block out dust and contaminants.
For technical drawings and 3-D models, click on a part number.
Overall | Mounting | Radial Load Cap., lbs. | ||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
For Shaft Dia. | Ht. | Lg. | Wd. | Flange Thick. | Hole Dia. | Hole Ctr.-to-Ctr. | Dynamic | Static | Max. Speed, rpm | Temp. Range, °F | Alignment Style | Lubrication | Each | |
Sealed Steel Bearings with Cast Iron Housing | ||||||||||||||
Shaft Mount Type: Set Screw | ||||||||||||||
1 1/4" | 4 5/8" | 4 5/8" | 1 3/4" | 9/16" | 17/32" | 3 5/8" | 5,750 | 3,450 | 2,200 | -20° to 400° | Self Aligning | Lubricated | 0000000 | 0000000 |
Threaded Track Rollers

Also known as cam followers, track rollers support loads while guiding and positioning work. Thread the stud directly into a component or secure with a nut for through-hole mounting.
Crowned rollers have a slight curve, which is invisible to the naked eye, to stay centered on surfaces that are not perfectly aligned and/or not perfectly flat.
Rollers with seal have end seals to protect rolling elements from dirt and contamination.
For technical drawings and 3-D models, click on a part number.

Roller | Stud | Thread | Shoulder | Radial Load Cap., lbs. | |||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
Dia. | Wd. | Dia. | Lg. | Size | Lg. | Dia. | Lg. | Max. Speed, rpm | Static | Dynamic | Max. Temp., °F | Bearing Type | Includes | Each | |
Black-Oxide Steel Flat Rollers without Seal | |||||||||||||||
1 3/4" | 1" | 3/4" | 1 3/4" | 3/4"-16 | 7/8" | 1 1/4" | 1/32" | 2,200 | 7,900 | 6,300 | 250° | Needle Roller | __ | 0000000 | 000000 |
1 3/4" | 1" | 1" | 1 3/4" | 1"-14 | 7/8" | 1 1/4" | 1/32" | 2,200 | 15,000 | 6,300 | 250° | Needle Roller | __ | 0000000 | 00000 |
Black-Oxide Steel Flat Rollers with Seal | |||||||||||||||
1 3/4" | 1" | 3/4" | 1 3/4" | 3/4"-16 | 7/8" | 1 1/4" | 1/32" | 2,200 | 7,900 | 6,300 | 250° | Needle Roller | __ | 0000000 | 00000 |
1 3/4" | 1" | 1" | 1 3/4" | 1"-14 | 7/8" | 1 1/4" | 1/32" | 2,200 | 15,000 | 6,300 | 250° | Needle Roller | __ | 0000000 | 00000 |
Black-Oxide Steel Crowned Rollers with Seal | |||||||||||||||
1 3/4" | 1" | 3/4" | 1 3/4" | 3/4"-16 | 7/8" | 1 1/4" | 1/32" | 2,200 | 7,900 | 6,300 | 250° | Needle Roller | __ | 0000000 | 00000 |
1 3/4" | 1" | 1" | 1 3/4" | 1"-14 | 7/8" | 1 1/4" | 1/32" | 2,200 | 15,000 | 6,300 | 250° | Needle Roller | __ | 0000000 | 00000 |
Steel Flat Rollers with Seal | |||||||||||||||
2" | 1 1/4" | 7/8" | 2" | 7/8"-14 | 1" | 1 13/64" | 1/32" | 2,200 | 16,000 | 9,600 | 250° | Needle Roller | Mounting Hardware | 0000000 | 00000 |
2" | 1 1/4" | 1 1/8" | 2" | 1 1/8"-12 | 1" | 1 13/32" | 1/32" | 2,200 | 21,000 | 9,600 | 250° | Needle Roller | Mounting Hardware | 000000 | 00000 |
Steel Crowned Rollers with Seal | |||||||||||||||
2" | 1 1/4" | 7/8" | 2" | 7/8"-14 | 1" | 1 13/64" | 1/32" | 2,200 | 16,000 | 9,600 | 250° | Needle Roller | Mounting Hardware | 0000000 | 00000 |
2" | 1 1/4" | 1 1/8" | 2" | 1 1/8"-12 | 1" | 1 13/32" | 1/32" | 2,200 | 21,000 | 9,600 | 250° | Needle Roller | Mounting Hardware | 0000000 | 000000 |

Roller, mm | Stud, mm | Thread | Shoulder, mm | Radial Load Cap., lbs. | |||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
Dia. | Wd. | Dia. | Lg. | Size | Pitch, mm | Lg., mm | Dia. | Lg. | Max. Speed, rpm | Static | Dynamic | Max. Temp., °F | Bearing Type | Each | |
Black-Oxide Steel Flat Rollers without Seal | |||||||||||||||
90 | 35 | 30 | 63 | M30 | 1.5 | 32 | 68 | 1 | 2,200 | 19,000 | 10,000 | 250° | Needle Roller | 00000000 | 0000000 |
Black-Oxide Steel Flat Rollers with Seal | |||||||||||||||
80 | 35 | 30 | 63 | M30 | 1.5 | 32 | 63 | 1 | 2,200 | 22,000 | 14,000 | 250° | Needle Roller | 00000000 | 000000 |
Black-Oxide Steel Crowned Rollers with Seal | |||||||||||||||
80 | 35 | 30 | 63 | M30 | 1.5 | 32 | 63 | 1 | 2,200 | 22,000 | 14,000 | 250° | Needle Roller | 00000000 | 000000 |
High-Load Threaded Track Rollers


With a double row of cylindrical roller bearings, these rollers provide the highest combination of speed and dynamic radial load ratings of any threaded track roller we offer. Also known as cam followers, track rollers support loads while guiding and positioning work. Thread the stud directly into a component or secure with a nut for through-hole mounting. All rollers are permanently lubricated.
Crowned rollers have a slight curve, invisible to the naked eye, which helps them stay centered on surfaces that are slightly misaligned or not perfectly flat.
Rollers with seal have an end seal to protect the rolling elements from dirt and contamination.
For technical drawings and 3-D models, click on a part number.
Roller | Stud | Thread | Shoulder | Radial Load Cap., lbs. | |||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
Dia. | Wd. | Dia. | Lg. | Size | Lg. | Dia. | Lg. | Max. Speed, rpm | Static | Dynamic | Max. Temp., °F | Bearing Type | Includes | Each | |
Black-Oxide Steel | |||||||||||||||
Flat Rollers without Seal | |||||||||||||||
1 1/4" | 3/4" | 3/4" | 1 1/4" | 3/4"-16 | 5/8" | 61/64" | 1/16" | 2,200 | 7,100 | 5,300 | 245° | Needle Roller | Mounting Hardware | 0000000 | 000000 |
1 3/8" | 3/4" | 3/4" | 1 1/4" | 3/4"-16 | 5/8" | 61/64" | 1/16" | 2,200 | 7,100 | 5,300 | 245° | Needle Roller | Mounting Hardware | 0000000 | 00000 |
Crowned Rollers with Seal | |||||||||||||||
1 1/4" | 3/4" | 3/4" | 1 1/4" | 3/4"-16 | 5/8" | 61/64" | 1/16" | 2,200 | 7,100 | 5,300 | 245° | Needle Roller | Mounting Hardware | 0000000 | 00000 |
1 3/8" | 3/4" | 3/4" | 1 1/4" | 3/4"-16 | 5/8" | 61/64" | 1/16" | 2,200 | 7,100 | 5,300 | 245° | Needle Roller | Mounting Hardware | 0000000 | 00000 |
Threaded Track Rollers with Adjustable Shoulder
Also known as eccentric track rollers, the shoulder adjusts up or down to align to your track, enabling uniform alignment among rollers in a system. Secure the stud with a nut for through-hole mounting. All rollers have end seals to protect rolling elements from dirt and contamination.
Crowned rollers have a slight curve, which is invisible to the naked eye, to stay centered on surfaces that are not perfectly aligned and/or not perfectly flat.
For technical drawings and 3-D models, click on a part number.



Roller | Stud | Thread | Shoulder | Radial Load Cap., lbs. | ||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
Dia. | Wd. | Dia. | Lg. | Size | Lg. | Dia. | Lg. | Ht. Adjustment Capability | Max. Speed, rpm | Static | Dynamic | Max. Temp., °F | Bearing Type | Includes | Each | |
Steel Flat Rollers with Seal | ||||||||||||||||
2" | 1 1/4" | 7/8" | 1" | 7/8"-14 | 1" | 1 3/16" | 1" | 0.03" | 2,200 | 16,000 | 9,600 | 250° | Needle Roller | Mounting Hardware | 0000000 | 000000 |
2 1/4" | 1 1/4" | 7/8" | 1" | 7/8"-14 | 1" | 1 3/16" | 1" | 0.03" | 2,200 | 16,000 | 9,600 | 250° | Needle Roller | Mounting Hardware | 0000000 | 00000 |
Steel Crowned Rollers with Seal | ||||||||||||||||
2" | 1 1/4" | 7/8" | 1" | 7/8"-14 | 1" | 1 3/16" | 1" | 0.03" | 2,200 | 16,000 | 9,600 | 250° | Needle Roller | Mounting Hardware | 0000000 | 00000 |
2 1/4" | 1 1/4" | 7/8" | 1" | 7/8"-14 | 1" | 1 3/16" | 1" | 0.03" | 2,200 | 16,000 | 9,600 | 250° | Needle Roller | Mounting Hardware | 0000000 | 00000 |
Corrosion-Resistant Threaded Track Rollers


Also known as cam followers, track rollers support loads while guiding and positioning work. Thread the stud directly into a component or secure with a nut for through-hole mounting. All rollers have end seals to protect rolling elements from dirt and contamination.
440C stainless steel rollers offer better corrosion resistance than chrome-plated steel rollers.
For technical drawings and 3-D models, click on a part number.
Roller | Stud | Thread | Shoulder | Radial Load Cap., lbs. | ||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
Dia. | Wd. | Dia. | Lg. | Size | Lg. | Dia. | Lg. | Max. Speed, rpm | Static | Dynamic | Max. Temp., °F | Bearing Type | Each | |
440C Stainless Steel Flat Rollers with Seal | ||||||||||||||
1 3/4" | 1" | 3/4" | 1 3/4" | 3/4"-16 | 7/8" | 1 3/64" | 1/32" | 2,200 | 5,500 | 5,500 | 250° | Needle Roller | 0000000 | 0000000 |
Shaft-Mount Track Rollers

Also known as yoke-style cam followers, these rollers have more mounting flexibility than threaded track rollers. They're typically mounted onto a shaft or clevis rod end. Lubricate rollers through a hole and groove in the inner ring.
Crowned rollers have a slight curve, which is invisible to the naked eye, to stay centered on surfaces that are not perfectly aligned and/or not perfectly flat.
Rollers with seal have end seals to protect rolling elements from dirt and contamination.
For technical drawings and 3-D models, click on a part number.

Roller | Radial Load Cap., lbs. | |||||||||
---|---|---|---|---|---|---|---|---|---|---|
Dia. | Wd. | For Shaft Dia. | Overall Wd. | Max. Speed, rpm | Static | Dynamic | Max. Temp., °F | Bearing Type | Each | |
Black-Oxide Steel Flat Rollers without Seal | ||||||||||
1 3/4" | 1" | 1/2" | 1 1/16" | 2,200 | 15,000 | 6,300 | 220° | Needle Roller | 0000000 | 000000 |
Black-Oxide Steel Flat Rollers with Seal | ||||||||||
1 3/4" | 1" | 1/2" | 1 1/16" | 2,200 | 15,000 | 6,300 | 220° | Needle Roller | 0000000 | 00000 |
Black-Oxide Steel Crowned Rollers without Seal | ||||||||||
1 3/4" | 1" | 1/2" | 1 1/16" | 2,200 | 14,000 | 6,300 | 220° | Needle Roller | 0000000 | 00000 |
Black-Oxide Steel Crowned Rollers with Seal | ||||||||||
1 3/4" | 1" | 1/2" | 1 1/16" | 2,200 | 15,000 | 6,300 | 220° | Needle Roller | 0000000 | 00000 |
Corrosion-Resistant Shaft-Mount Track Rollers


Also known as yoke-style cam followers, these rollers have more mounting flexibility than threaded track rollers. They're typically mounted onto a shaft or clevis rod end. Lubricate rollers through a hole and groove in the inner ring. Rollers have end seals to protect rolling elements from dirt and contamination.
For technical drawings and 3-D models, click on a part number.
Roller | Radial Load Cap., lbs. | |||||||||
---|---|---|---|---|---|---|---|---|---|---|
Dia. | Wd. | For Shaft Dia. | Overall Wd. | Max. Speed, rpm | Static | Dynamic | Max. Temp., °F | Bearing Type | Each | |
440C Stainless Steel Flat Rollers with Seal | ||||||||||
1 3/4" | 1" | 1/2" | 1 1/16" | 2,200 | 14,000 | 5,500 | 250° | Needle Roller | 0000000 | 0000000 |
Shaft-Mount V-Groove Track Rollers


Also known as yoke-style cam followers, these rollers have more mounting flexibility than threaded track rollers. They're typically mounted onto a shaft or clevis rod end. Rollers are for use with Angle Rails for V-Groove Track Rollers. They handle radial and thrust (top and side) loads and work well in dirty environments because debris falls off the angled rail. All rollers are permanently lubricated.
Sealed rollers block out dust and other contaminants better than shielded rollers, but they hold more heat. Their seals also help retain lubricant.
For technical drawings and 3-D models, click on a part number.
Roller | Groove | Radial Load Cap., lbs. | ||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
Dia. | Wd. | For Shaft Dia. | Overall Wd. | Wd. | Dp. | Max. Speed, rpm | Static | Dynamic | Static Thrust Load Cap., lbs. | Max. Temp., °F | Bearing Type | Features | Each | |
Steel V-Groove Rollers with Seal | ||||||||||||||
1 13/16" | 5/8" | 12mm | 5/8" | 5/16" | 3/16" | 2,200 | 1,300 | 1,300 | 380 | 210° | Ball | Single Sealed and Shielded | 0000000 | 000000 |
440C Stainless Steel V-Groove Rollers with Seal | ||||||||||||||
1 13/16" | 5/8" | 12mm | 5/8" | 5/16" | 3/16" | 2,200 | 1,300 | 1,300 | 380 | 210° | Ball | Single Sealed and Shielded | 0000000 | 000000 |
440C Stainless Steel V-Groove Rollers without Seal | ||||||||||||||
1 13/16" | 5/8" | 12mm | 5/8" | 5/16" | 3/16" | 2,200 | 1,100 | 1,100 | 310 | 500° | Ball | Shielded | 0000000 | 000000 |
Threaded V-Groove Track Rollers

Thread the stud directly into a component or secure with a nut for through-hole mounting. Rollers are for use with Angle Rails for V-Groove Track Rollers. They handle radial and thrust (top and side) loads and work well in dirty environments because debris falls off the angled rail. Also known as cam followers, track rollers support loads while guiding and positioning work. All rollers are permanently lubricated.
440C stainless steel rollers offer better corrosion resistance than steel rollers.
Rollers with a seal block out dust and other contaminants better than shielded rollers, but they hold more heat. Their seal also helps retain lubricant.
For technical drawings and 3-D models, click on a part number.

Roller, mm | Stud, mm | Thread | Groove, mm | Radial Load Cap., lbs. | |||||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
Dia. | Wd. | Dia. | Lg. | Size | Pitch, mm | Lg., mm | Shoulder Lg., mm | Hex Shoulder Wd., mm | Wd. | Dp. | Max. Speed, rpm | Static | Dynamic | Static Thrust Load Cap., lbs. | Max. Temp., °F | Bearing Type | Includes | Each | |
440C Stainless Steel V-Groove Rollers with Seal | |||||||||||||||||||
46 | 16 | 12 | 15 | M12 | 1.75 | 15 | 5.6 | 19.05 | 8 | 4 | 2,200 | 1,100 | 1,100 | 300 | 500° | Ball | __ | 0000000 | 0000000 |
46 | 16 | 12 | 32 | M12 | 1.75 | 18 | 3.4 | 19 | 8 | 4 | 2,200 | 1,100 | 1,100 | 300 | 500° | Ball | Mounting Hardware | 0000000 | 000000 |
Steel V-Groove Rollers with Seal | |||||||||||||||||||
46 | 16 | 12 | 15 | M12 | 1.75 | 15 | 5.6 | 19.05 | 8 | 4 | 2,200 | 1,300 | 1,300 | 380 | 245° | Ball | __ | 0000000 | 00000 |
46 | 16 | 12 | 30 | M12 | 1.75 | 18 | 3.4 | 19 | 8 | 4 | 2,200 | 1,300 | 1,300 | 350 | 210° | Ball | Mounting Hardware | 0000000 | 00000 |
Threaded V-Groove Track Rollers with Adjustable Shoulder

Also known as eccentric track rollers, the shoulder adjusts up or down to align to your track, enabling uniform alignment among rollers in a system. Rollers are for use with Angle Rails for V-Groove Track Rollers. They handle radial and thrust (top and side) loads and work well in dirty environments because debris falls off the angled rail. Secure the stud with a nut for through-hole mounting. All rollers are permanently lubricated.
440C stainless steel rollers offer better corrosion resistance than steel rollers.
Rollers with a seal block out dust and other contaminants better than shielded rollers, but they hold more heat. Their seal also helps retain lubricant.
For technical drawings and 3-D models, click on a part number.

Roller, mm | Stud, mm | Thread | Groove, mm | Radial Load Cap., lbs. | ||||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
Dia. | Wd. | Dia. | Lg. | Size | Pitch, mm | Lg., mm | Shoulder Lg., mm | Hex Shoulder Wd., mm | Wd. | Dp. | Max. Speed, rpm | Static | Dynamic | Static Thrust Load Cap., lbs. | Max. Temp., °F | Includes | Each | |
Steel V-Groove Rollers with Seal | ||||||||||||||||||
46 | 16 | 11 | 15 | M10 | 1.5 | 11 | 5.7 | 19.05 | 8 | 4 | 2,200 | 1,300 | 1,300 | 380 | 245° | Mounting Hardware | 0000000 | 000000 |
46 | 16 | 12 | 30 | M12 | 1.75 | 18 | 3.4 | 19 | 8 | 4 | 2,200 | 1,300 | 1,300 | 350 | 210° | Mounting Hardware | 0000000 | 00000 |
440C Stainless Steel V-Groove Rollers with Seal | ||||||||||||||||||
46 | 16 | 12 | 30 | M12 | 1.75 | 18 | 3.4 | 19 | 8 | 4 | 2,200 | 1,100 | 1,100 | 300 | 500° | Mounting Hardware | 0000000 | 000000 |
Sanitary Shaft-Mount V-Groove Track Rollers


Support and guide loads on angle rails in food, pharmaceutical, and other sanitary environments. Also known as yoke-style cam followers, these track rollers offer more mounting flexibility than threaded alternatives and are typically mounted on shafts and clevis rod ends. They’re permanently lubricated to prevent contamination, with sealed and shielded bearings blocking out debris and liquids to protect the lubricant. FDA compliant and NSF registered H1, the lubricant is safe for incidental contact with food. These track rollers are made of stainless steel, so they won’t corrode from frequent washdowns with harsh cleaners.
Double-sealed rollers are better protected from high-pressure liquid and debris than single-sealed rollers, and also operate within a broader temperature range. They’re built to withstand the frequent high-pressure, high-temperature washdowns found in food and pharmaceutical plants.
For technical drawings and 3-D models, click on a part number.
Roller | Groove | Radial Load Capacity, lbs. | ||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
Diameter | Width | For Shaft Diameter | Overall Width | Width | Depth | Maximum Speed, rpm | Static | Dynamic | Static Thrust Load Capacity, lbs. | Maximum Temperature, °F | Bearing Type | Specifications Met | Each | |
440C Stainless Steel V-Groove Rollers With Seal | ||||||||||||||
Single-Sealed and Shielded | ||||||||||||||
1 13/16" | 5/8" | 15/32" | 5/8" | 5/16" | 5/16" | 2,200 | 1,300 | 1,300 | 380 | 175° | Ball | FDA Compliant 21 CFR 178.3570, NSF Registered H1 | 0000000 | 0000000 |
Double-Sealed and Shielded | ||||||||||||||
1 13/16" | 5/8" | 15/32" | 5/8" | 5/16" | 5/16" | 2,200 | 1,100 | 1,100 | 130 | 210° | Ball | FDA Compliant 21 CFR 178.3570, NSF Registered H1 | 0000000 | 000000 |
Sanitary Threaded V-Groove Track Rollers


Guide loads along angle rail tracks in food and pharmaceutical plants or other sanitary environments with these threaded rollers. They’re permanently lubricated, a feature often seen in sanitary areas where repeated lubrication could cause contamination. Their lubricant is NSF registered H1 as safe for incidental contact with food. They’re made of stainless steel, so they won’t corrode from frequent washdowns with harsh cleaners. The bearings are sealed and shielded to keep out liquid and make sure the lubricant stays intact. These rollers have a V-groove profile, which allows debris to fall off when they’re mounted on angle rails. They’re also known as cam followers.
Rollers with a standard shoulder have a threaded mounting stud. Thread them directly into a component, or secure them with a nut for through-hole mounting.
Rollers with an adjustable shoulder are also known as eccentric track rollers. They can be moved up and down, and they’re commonly used alongside standard rollers to correct misalignment. Secure them with a nut for through-hole mounting.
For technical drawings and 3-D models, click on a part number.
Roller, mm | Stud, mm | Thread | Groove, mm | Radial Load Cap., lbs. | ||||||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
Dia. | Wd. | Dia. | Lg. | Size | Pitch, mm | Lg., mm | Shoulder Lg., mm | Hex Shoulder Wd., mm | Ht. Adjustment Capability, mm | Wd. | Dp. | Max. Speed, rpm | Static | Dynamic | Static Thrust Load Cap., lbs. | Max. Temp., °F | Bearing Type | Includes | Each | |
Single-Sealed 440C Stainless Steel V-Groove Rollers | ||||||||||||||||||||
Standard Shoulder | ||||||||||||||||||||
46 | 16 | 12 | 30 | M12 | 1.75 | 18 | 4.1 | 19 | 1.5 | 8 | 4 | 2,200 | 1,300 | 1,300 | 380 | 175° | Ball | Mounting Hardware | 0000000 | 0000000 |
Adjustable Shoulder | ||||||||||||||||||||
46 | 16 | 12 | 30 | M12 | 1.75 | 18 | 4.1 | 19 | 1.5 | 8 | 4 | 2,200 | 1,300 | 1,300 | 380 | 175° | Ball | Mounting Hardware | 0000000 | 000000 |