46 Products

Install these acetal bearings in caustic environments and where lubrication can’t be used. They have good all-around corrosion and chemical resistance. The flange ensures proper positioning inside a tube or housing.

For technical drawings and 3-D models, click on a part number.

Slip these bearings onto a shaft and secure with the included set screws, no special tools required. All have an extended inner ring for additional shaft support.

Bearings with a black-oxide steel ring have some corrosion resistance.

Sealed bearings block out dust and other contaminants better than shielded bearings.

Bearings with a retaining ring have a removable retaining ring that holds the bearing inside a housing.

For technical drawings and 3-D models, click on a part number.

Designed to stand up to frequent washdowns, you can quickly secure these ball bearings onto shafts with the clamp-on collar in food, beverage, pharmaceutical, and chemical plants. The collar centers your shafts and secures them better than set screw ball bearings, which reduces vibration and noise. To install these bearings, tighten the single screw on the collar around its inner ring on your shaft for a mar-free hold.

Coated with nickel, the steel rings on these bearings won’t corrode from water and harsh cleaners, similar to 304 stainless steel. The inner ring is extended for added shaft support. All of these bearings have NSF registered H1 lubrication, which is certified for incidental contact with food and is suitable for food and beverage applications.

For technical drawings and 3-D models, click on a part number.

Secure these bearings in washdown areas, such as food, beverage, pharmaceutical, and chemical plants, by tightening the set screw onto a shaft—no additional collar needed. Similar to 304 stainless steel, the nickel-coated steel rings on these bearings won’t break down from water. The extended inner ring increases shaft support. All of these bearings have NSF registered H1 lubrication, which is certified for incidental contact with food.

For technical drawings and 3-D models, click on a part number.

Steel balls and washers allow these bearings to handle higher loads than bearings with stainless steel components. With an open design, they dissipate heat more efficiently than one-piece thrust ball bearings.

Bearings with steel cage and with bronze cage handle higher loads and speeds than bearings with a plastic cage.

For technical drawings and 3-D models, click on a part number.

Found anywhere from machine tool spindles to conveyor rollers, these bearings have a two-piece design that allows for adjustment.

For technical drawings and 3-D models, click on a part number.

Mounting with threaded holes in their base and IP69K certified for washdown environments, these bearings fit in tight spaces and are used in food-, beverage-, pharmaceutical-, and chemical-processing plants. Also known as tapped-base mounted ball bearings, they require access to the underside of the mounting surface. All have NSF registered H1 lubrication, which is certified for incidental contact with food and suitable for use in food and beverage applications.

Set screw bearings secure to shafts when you tighten their screw. They don’t need a collar, but the screw does leave some marring on shafts.

Concentric lock bearings have a locking collar to center shafts and secure them better than set screw bearings, so there’s less vibration and noise. To install them, tighten the locking collar’s screw so it grips the inner ring.

For technical drawings and 3-D models, click on a part number.

Made to withstand frequent washdowns, these bearings are permanently lubricated, which means you’ll never have to add lubricant. Use them in hard-to-reach areas in food, beverage, pharmaceutical, and chemical plants. With a 316 stainless steel housing, these bearings won’t rust from salt water, chlorine, or chemicals. All are lubricated with NSF registered H1 grease, which is certified for incidental contact with food.

Set-screw bearings secure to shafts as you tighten their screw. They don’t need a collar; however, the screws leave some marring on the shaft.

For technical drawings and 3-D models, click on a part number.

Also known as cam followers, track rollers support loads while guiding and positioning work. Thread the stud directly into a component or secure with a nut for through-hole mounting.

Crowned rollers have a slight curve, which is invisible to the naked eye, to stay centered on surfaces that are not perfectly aligned and/or not perfectly flat.

Rollers with seal have end seals to protect rolling elements from dirt and contamination.

For technical drawings and 3-D models, click on a part number.

Also known as cam followers, track rollers support loads while guiding and positioning work. Thread the stud directly into a component or secure with a nut for through-hole mounting. All rollers have end seals to protect rolling elements from dirt and contamination.

440C stainless steel rollers offer better corrosion resistance than chrome-plated steel rollers.

For technical drawings and 3-D models, click on a part number.