63 Products

Slip these bearings onto a shaft and secure with the included set screws, no special tools required. All have an extended inner ring for additional shaft support.

Bearings with a black-oxide steel ring have some corrosion resistance.

Sealed bearings block out dust and other contaminants better than shielded bearings.

Bearings with a retaining ring have a removable retaining ring that holds the bearing inside a housing.

For technical drawings and 3-D models, click on a part number.

These bearings have angular raceways for combined thrust and radial loads—install them where precision tolerances are required for accuracy and high speeds. They’re often used in spindle applications. To handle thrust loads in both directions, they have a double-row construction. Pair them with cylindrical roller bearings to better handle radial loads. They have an open construction to dissipate heat efficiently.

For technical drawings and 3-D models, click on a part number.

Steel balls and washers allow these bearings to handle higher loads than bearings with stainless steel components. With an open design, they dissipate heat more efficiently than one-piece thrust ball bearings.

Bearings with steel cage and with bronze cage handle higher loads and speeds than bearings with a plastic cage.

For technical drawings and 3-D models, click on a part number.

In addition to handling higher loads than three-piece ball bearings, one-piece bearings are easier to handle. They have an outer band that holds the bearing together and acts as a shield against dust and other contaminants.

For technical drawings and 3-D models, click on a part number.

Found anywhere from machine tool spindles to conveyor rollers, these bearings have a two-piece design that allows for adjustment.

For technical drawings and 3-D models, click on a part number.

Install these bearings directly onto hardened and ground shafts. They have higher load capacity, speed, and accuracy than standard needle-roller bearings.

Sealed bearings block out dust and other contaminants.

Shaft liners allow you to use the bearing on unhardened and unground shafts.

For technical drawings and 3-D models, click on a part number.

Bearings are self-aligning to compensate for shaft misalignment. Seals block out dust and contaminants.

Bearings with a set screw secure to shafts without using a collar. They let shafts rotate in both directions, so they’re good for applications where you need to reverse. However, the set screw will leave some marring on the shaft.

Bearing with concentric lock use adapter sleeves (sold separately) to lock onto shafts in a way that enables high running speeds with little vibration. They work for applications that require reversing because they allow shafts to rotate in both directions.

For technical drawings and 3-D models, click on a part number.

Meeting IP69K for washdown environments, these mounted ball bearings are used in food, beverage, pharmaceutical, and chemical plants. They have excellent corrosion resistance and prevent rusting caused by salt water, chlorine solutions, and chemicals because their housing is 316 stainless steel. All have USDA H1 approved lubrication, which is certified for incidental contact with food and is suitable for food and beverage applications.

Set screw bearings secure to shafts as you tighten their screw. They don’t need a collar, but the screw does leave some marring on shafts.

Clamp on bearings have a locking collar to center shafts and secure them better than set screw bearings, so there’s less vibration and noise. To install them, tighten the locking collar’s screw until it grips the inner ring.

Snap optional covers onto bearings to shield them from moisture. Made of polypropylene, they resist corrosion, won’t absorb water, and are FDA compliant.

For technical drawings and 3-D models, click on a part number.

Roller bearings have a thinner profile and larger contact area than ball bearings, making them stronger and more space-efficient than ball bearings.

Sealed bearings block out dust and contaminants.

For technical drawings and 3-D models, click on a part number.

Designed with a thin, compact housing, these bearings are good for space-constrained applications. Seals block out dust and contaminants.

Steel bearings are stronger than stainless steel bearings, but not as corrosion resistant.

For technical drawings and 3-D models, click on a part number.

Used in food, beverage, pharmaceutical, and chemical plants, these mounted ball bearings are IP69K certified for washdown environments and have a two-bolt flange for mounting. Their 316 stainless steel housing has excellent corrosion resistance and prevents rust caused by salt water, chlorine solutions, and chemicals. All have USDA H1 approved lubrication, which is certified for incidental contact with food and is suitable for food and beverage applications.

Set screw bearings grip shafts as you tighten their screw. They don’t use a collar, but the screw leaves some marring on shafts.

Clamp on bearings have a locking collar to center shafts and secure them better than set screw bearings, so there’s less vibration and noise. To install them, tighten the locking collar’s screw until it secures against the inner ring.

Snap optional covers onto bearings to protect them from moisture. Made of polypropylene, they resist corrosion, don’t absorb water, and are FDA compliant.

For technical drawings and 3-D models, click on a part number.

Permanently lubricated and IP69K certified for washdown environments, these mounted ball bearings are useful for hard-to-reach areas in food, beverage, pharmaceutical, and chemical plants. Mount them using their two-bolt flange. For excellent corrosion resistance and preventing rust caused by salt water, chlorine solutions, and chemicals, their housing is made of 316 stainless steel. All have USDA H1 approved lubrication, which is certified for incidental contact with food and is suitable for food and beverage applications.

Set screw bearings grip shafts when you tighten their screw. They don’t need a collar, but the screw leaves some marring on shafts.

Concentric lock bearings have a locking collar to center shafts and secure them better than set screw bearings, so there’s less vibration and noise. Install them by tightening the locking collar’s screw until it presses against the inner ring.

Snap optional covers onto bearings to shield them from moisture. Made of polypropylene, they resist corrosion, don’t absorb water, and are FDA compliant.

For technical drawings and 3-D models, click on a part number.

Bearings are self-aligning to compensate for shaft misalignment. Seals block out dust and contaminants.

Set screw bearings secure to shafts as you tighten their screw. They don’t need a collar, but the screw leaves some marring on shafts. Use them in applications where shafts rotate in both directions.

Concentric lock bearings enable high running speeds while maintaining low levels of vibration; you must pair them with an adapter sleeve (sold separately). They’re good for applications where shafts rotate in both directions.

For technical drawings and 3-D models, click on a part number.

The tapered rollers in these bearings support large shafts at high static loads. Seals block out dust and contaminants.

For technical drawings and 3-D models, click on a part number.

Meeting IP69K for washdown environments, these mounted ball bearings are used in food, beverage, pharmaceutical, and chemical plants. They have excellent corrosion resistance and prevent rusting caused by salt water, chlorine solutions, and chemicals because their housing is 316 stainless steel. All have USDA H1 approved lubrication, which is certified for incidental contact with food and is suitable for food and beverage applications.

Set screw bearings secure to shafts as you tighten their screw. They don’t need a collar, but the screw does leave some marring on shafts.

Clamp on bearings have a locking collar to center shafts and secure them better than set screw bearings, so there’s less vibration and noise. To install them, tighten the locking collar’s screw until it grips the inner ring.

Snap optional covers onto bearings to shield them from moisture. Made of polypropylene, they resist corrosion, won’t absorb water, and are FDA compliant.

For technical drawings and 3-D models, click on a part number.

Combine with threaded pipe to mount these bearings in a variety of positions without the need for a flat mounting surface. Bearings are self-aligning to compensate for shaft misalignment. Seals block out dust and contaminants.

NPSM (National Pipe Straight Mechanical) threads are compatible with NPT threads. See more about pipe thread type and sizing.

For technical drawings and 3-D models, click on a part number.