50 Products

Found anywhere from machine tool spindles to conveyor rollers, these bearings have a two-piece design that allows for adjustment.

Zinc-coated steel bearings provide better corrosion resistance than steel bearings.

For technical drawings and 3-D models, click on a part number.

Install these bearings directly onto hardened and ground shafts. They have higher load capacity, speed, and accuracy than standard needle-roller bearings.

Sealed bearings block out dust and other contaminants.

Shaft liners allow you to use the bearing on unhardened and unground shafts.

For technical drawings and 3-D models, click on a part number.

Bearings are self-aligning to compensate for shaft misalignment. Seals block out dust and contaminants.

Bearings with eccentric lock have a collar that you twist in one direction to grip and the other to release. Compared to bearings with a set screw, they’re easier to install, require less adjustment over time, and are better for high-speed applications. But, they only work on shafts that spin in one direction.

Bearing with concentric lock use adapter sleeves (sold separately) to lock onto shafts in a way that enables high running speeds with little vibration. They work for applications that require reversing because they allow shafts to rotate in both directions.

For technical drawings and 3-D models, click on a part number.

Bearings are self-aligning to compensate for shaft misalignment. Seals block out dust and contaminants.

Set screw bearings secure to shafts as you tighten their screw. They don’t need a collar, but the screw leaves some marring on shafts. Use them in applications where shafts rotate in both directions.

For technical drawings and 3-D models, click on a part number.

Also known as cam followers, track rollers support loads while guiding and positioning work. Thread the stud directly into a component or secure with a nut for through-hole mounting.

Crowned rollers have a slight curve, which is invisible to the naked eye, to stay centered on surfaces that are not perfectly aligned and/or not perfectly flat.

Rollers with seal have end seals to protect rolling elements from dirt and contamination.

For technical drawings and 3-D models, click on a part number.

Thread the stud directly into a component or secure with a nut for through-hole mounting. Rollers are for use with Angle Rails for V-Groove Track Rollers. They handle radial and thrust (top and side) loads and work well in dirty environments because debris falls off the angled rail. Also known as cam followers, track rollers support loads while guiding and positioning work. All rollers are permanently lubricated.

440C stainless steel rollers offer better corrosion resistance than steel rollers.

Rollers with a seal block out dust and other contaminants better than shielded rollers, but they hold more heat. Their seal also helps retain lubricant.

For technical drawings and 3-D models, click on a part number.

Also known as yoke-style cam followers, these rollers have more mounting flexibility than threaded track rollers. They're typically mounted onto a shaft or clevis rod end. Rollers are for use with Angle Rails for V-Groove Track Rollers. They handle radial and thrust (top and side) loads and work well in dirty environments because debris falls off the angled rail. All rollers are permanently lubricated.

Sealed rollers block out dust and other contaminants better than shielded rollers, but they hold more heat. Their seals also help retain lubricant.

For technical drawings and 3-D models, click on a part number.

Also known as eccentric track rollers, the shoulder adjusts up or down to align to your track, enabling uniform alignment among rollers in a system. Rollers are for use with Angle Rails for V-Groove Track Rollers. They handle radial and thrust (top and side) loads and work well in dirty environments because debris falls off the angled rail. Secure the stud with a nut for through-hole mounting. All rollers are permanently lubricated.

440C stainless steel rollers offer better corrosion resistance than steel rollers.

Rollers with a seal block out dust and other contaminants better than shielded rollers, but they hold more heat. Their seal also helps retain lubricant.

For technical drawings and 3-D models, click on a part number.

Support and guide loads on angle rails in food, pharmaceutical, and other sanitary environments. Also known as yoke-style cam followers, these track rollers offer more mounting flexibility than threaded alternatives and are typically mounted on shafts and clevis rod ends. They’re permanently lubricated to prevent contamination, with sealed and shielded bearings blocking out debris and liquids to protect the lubricant. FDA compliant and NSF registered H1, the lubricant is safe for incidental contact with food. These track rollers are made of stainless steel, so they won’t corrode from frequent washdowns with harsh cleaners.

Double-sealed rollers are better protected from high-pressure liquid and debris than single-sealed rollers, and also operate within a broader temperature range. They’re built to withstand the frequent high-pressure, high-temperature washdowns found in food and pharmaceutical plants.

For technical drawings and 3-D models, click on a part number.