System of Measurement System of Measurement |
---|
|
Mounted Bearing Type Mounted Bearing Type |
---|
![]() | Base Mount |
![]() | Two-Bolt Flange Mount |
![]() | Four-Bolt Flange Mount |
Housing Material Housing Material |
---|
|
Mounting Hole Center-to-Center Mounting HoleCenter-to-Center |
---|
|
|
Bearing Material Bearing Material |
---|
|
Alignment Style Alignment Style |
---|
|
Seal Type Seal Type |
---|
|
Dynamic Radial Load Capacity Dynamic Radial Load Capacity |
---|
|
|
For Load Direction For Load Direction |
---|
![]() | Radial |
Maximum Speed Maximum Speed | Show |
---|
|
Maximum Speed Maximum Speed | Hide |
---|
Maximum Temperature Maximum Temperature |
---|
|
RoHS (Restriction of Hazardous Substances) RoHS (Restriction ofHazardous Substances) |
---|
|
REACH (Registration, Evaluation, Authorization and Restriction of Chemicals) REACH (Registration,Evaluation, Authorization and Restriction of Chemicals) |
---|
|
About Ball and Roller Bearings
More
Precision Needle-Roller Bearings


Install these bearings directly onto hardened and ground shafts. They have higher load capacity, speed, and accuracy than standard needle-roller bearings.
Sealed bearings block out dust and other contaminants.
Shaft liners allow you to use the bearing on unhardened and unground shafts.
For technical drawings and 3-D models, click on a part number.
Bearings | ||||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
Radial Load Cap., lbs. | Optional Shaft Liners | |||||||||||||
For Shaft Dia. | For Housing ID | Wd. | Ring Material | Dynamic | Static | Max. Speed, rpm | Lubrication | For Shaft Surface Smoothness (Ra), microinch | Temp. Range., °F | Each | For Shaft Dia. | Each | ||
Sealed | ||||||||||||||
3/4" | 1 1/4" | 1" | Steel | 4,950 | 5,400 | 5,100 | Lubricated | 12 | -30° to 250° | 0000000 | 000000 | 1/2" | 0000000 | 000000 |
Mounted Ball Bearings
Bearings are self-aligning to compensate for shaft misalignment. Seals block out dust and contaminants.
Bearings with nickel-plated cast iron housing are more corrosion resistant and durable than bearings with a cast iron housing.
Bearings with a set screw secure to shafts without using a collar. They let shafts rotate in both directions, so they’re good for applications where you need to reverse. However, the set screw will leave some marring on the shaft.
For technical drawings and 3-D models, click on a part number.

Overall | Mounting | Radial Load Cap., lbs. | |||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
For Shaft Dia. | Center Ht. | Ht. | Lg. | Wd. | Hole Lg. | Hole Wd. | Hole Ctr.-to-Ctr. | Dynamic | Static | Max. Speed, rpm | Temp. Range, °F | Alignment Style | Lubrication | Each | |
Sealed Steel Bearings with Nickel-Plated Cast Iron Housing | |||||||||||||||
Shaft Mount Type: Set Screw | |||||||||||||||
1" | 1 7/16" | 3 5/32" | 5 1/2" | 1 17/32" | 23/32" | 1/2" | 4 1/8" | 3,140 | 1,760 | 5,100 | 0° to 210° | Self Aligning | Lubricated | 0000000 | 000000 |
Low-Profile Mounted Ball Bearings


Designed with a thin, compact housing, these bearings are good for space-constrained applications.
Bearings with steel housing are stronger than bearings with stainless steel and aluminum housings. They are self-aligning to compensate for shaft misalignment. Seals block out dust and contaminants.
Bearings with 304 stainless steel housing are more corrosion resistant than those with steel and aluminum housings. They are self-aligning to compensate for shaft misalignment. Seals block out dust and contaminants.
Sealed bearings block out dust and other contaminants better than shielded bearings.
For technical drawings and 3-D models, click on a part number.
Overall | Mounting | Radial Load Cap., lbs. | |||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
For Shaft Dia. | Center Ht. | Ht. | Lg. | Wd. | Hole Lg. | Hole Wd. | Hole Ctr.-to-Ctr. | Dynamic | Static | Max. Speed, rpm | Temp. Range, °F | Alignment Style | Lubrication | Each | |
Sealed Steel Bearings with Steel Housing | |||||||||||||||
Shaft Mount Type: Set Screw | |||||||||||||||
7/8" | 1 1/8" | 2 7/32" | 4 1/4" | 1 25/64" | 9/16" | 13/32" | 3 25/64" | 3,140 | 1,760 | 5,100 | 0° to 210° | Self Aligning | Lubricated | 0000000 | 000000 |
1" | 1 1/8" | 2 7/32" | 4 1/4" | 1 25/64" | 9/16" | 13/32" | 3 3/8" | 3,140 | 1,760 | 5,100 | 0° to 210° | Self Aligning | Lubricated | 0000000 | 00000 |
Overall | Mounting | Radial Load Cap., lbs. | |||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
For Shaft Dia. | Center Ht. | Ht. | Lg. | Wd. | Hole Lg. | Hole Wd. | Hole Ctr.-to-Ctr. | Dynamic | Static | Max. Speed, rpm | Temp. Range, °F | Alignment Style | Lubrication | Each | |
Sealed 440C Stainless Steel Bearings with 304 Stainless Steel Housing | |||||||||||||||
Shaft Mount Type: Set Screw | |||||||||||||||
1" | 1 1/8" | 2 7/32" | 4 1/2" | 1 3/8" | 9/16" | 13/32" | 3 3/8" | 2,670 | 1,410 | 5,100 | 0° to 210° | Self Aligning | Lubricated | 0000000 | 000000 |
Mounted Ball Bearings with Two-Bolt Flange

Bearings are self-aligning to compensate for shaft misalignment. Seals block out dust and contaminants.
Bearings with a set-screw shaft mount secure to shafts with no need for an additional collar. They can be used for bi-directional shaft rotation when applications require reversing action. The set screw may cause some marring on the shaft.
Bearings with nickel-plated cast iron housing are more corrosion resistant and durable than bearings with a cast iron housing.
For technical drawings and 3-D models, click on a part number.
Overall | Mounting | Radial Load Cap., lbs. | ||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
For Shaft Dia. | Ht. | Lg. | Wd. | Flange Thick. | Hole Dia. | Hole Ctr.-to-Ctr. | Dynamic | Static | Max. Speed, rpm | Temp. Range, °F | Alignment Style | Lubrication | Each | |
Sealed Steel Bearings with Nickel-Plated Cast Iron Housing | ||||||||||||||
Shaft Mount Type: Set Screw | ||||||||||||||
1" | 2 11/16" | 5 1/8" | 1 13/32" | 1/2" | 15/32" | 3 57/64" | 3,140 | 1,760 | 5,100 | 0° to 210° | Self Aligning | Lubricated | 0000000 | 000000 |
Low-Profile Mounted Ball Bearings with Two-Bolt Flange

Designed with a thin, compact housing, these bearings are good for space-constrained applications. Seals block out dust and contaminants.
Steel bearings are stronger than stainless steel bearings, but not as corrosion resistant.
Stainless steel bearings are more corrosion resistant than steel bearings.
Self-aligning bearings compensate for shaft misalignment.
For technical drawings and 3-D models, click on a part number.
Overall | Mounting | Radial Load Cap., lbs. | |||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
For Shaft Dia. | Ht. | Lg. | Wd. | Flange Thick. | Hole Dia. | Hole Ctr.-to-Ctr. | Dynamic | Static | Max. Speed, rpm | Min. Temp. Range, °F | Max. Temp. Range, °F | Alignment Style | Lubrication | Each | |
Sealed 440C Stainless Steel Bearings with 304 Stainless Steel Housing | |||||||||||||||
Shaft Mount Type: Set Screw | |||||||||||||||
7/8" | 2 51/64" | 3 3/4" | 1 11/32" | 5/32" | 11/32" | 3" | 2,650 | 1,400 | 5,100 | 0° | 210° | Self Aligning | Lubricated | 0000000 | 000000 |
1" | 2 51/64" | 3 3/4" | 1 11/32" | 5/32" | 11/32" | 3" | 2,650 | 1,400 | 5,100 | 0° | 210° | Self Aligning | Lubricated | 0000000 | 00000 |
Sealed Steel Bearings with Steel Housing | |||||||||||||||
Shaft Mount Type: Set Screw | |||||||||||||||
7/8" | 2 25/32" | 3 3/4" | 1 1/16" | 5/32" | 23/64" | 2 63/64" | 3,100 | 1,750 | 5,100 | 0° | 210° | Self Aligning | Lubricated | 0000000 | 00000 |
1" | 2 25/32" | 3 3/4" | 1 1/8" | 5/32" | 23/64" | 3" | 3,100 | 1,750 | 5,100 | 0° | 210° | Self Aligning | Lubricated | 0000000 | 00000 |
Mounted Ball Bearings with Four-Bolt Flange
Bearings are self-aligning to compensate for shaft misalignment. Seals block out dust and contaminants.
Bearings with nickel-plated cast iron housing are more corrosion resistant and durable than bearings with a cast iron housing.
Set screw bearings secure to shafts as you tighten their screw. They don’t need a collar, but the screw leaves some marring on shafts. Use them in applications where shafts rotate in both directions.
For technical drawings and 3-D models, click on a part number.

Overall | Mounting | Radial Load Cap., lbs. | ||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
For Shaft Dia. | Ht. | Lg. | Wd. | Flange Thick. | Hole Dia. | Hole Ctr.-to-Ctr. | Dynamic | Static | Max. Speed, rpm | Temp. Range, °F | Alignment Style | Lubrication | Each | |
Sealed Steel Bearings with Nickel-Plated Cast Iron Housing | ||||||||||||||
Shaft Mount Type: Set Screw | ||||||||||||||
1" | 3 3/4" | 3 3/4" | 1 13/32" | 1/2" | 29/64" | 2 3/4" | 3,140 | 1,760 | 5,100 | 0° to 210° | Self Aligning | Lubricated | 0000000 | 000000 |