Ball Bearing Type Ball Bearing Type |
|---|
 | Standard |
Ring Material Ring Material |
|---|
|
Lubrication Lubrication |
|---|
|
Maximum Speed Maximum Speed | Show |
|---|
|
Maximum Speed Maximum Speed | Hide |
|---|
Dynamic Radial Load Capacity Dynamic RadialLoad Capacity |
|---|
|
|
For Shaft Width For Shaft Width |
|---|
|
Static Radial Load Capacity Static Radial Load Capacity |
|---|
|
|
Ball Material Ball Material |
|---|
|
DFARS (Defense Acquisition Regulations Supplement) DFARS (Defense AcquisitionRegulations Supplement) |
|---|
About Ball and Roller Bearings
More
Ball Bearings
Shielded bearings block out dust and other contaminants, but do not dissipate heat as efficiently as open bearings.
For technical drawings and 3-D models, click on a part number.
Radial Load Cap., lbs. | ||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|
| Bearing Trade Number | For Shaft Dia. | For Housing ID | Wd. | Ring Material | Dynamic | Static | Max. Speed, rpm | Lubrication | Temp. Range, °F | ABEC Rating | Each | |
| R24-2Z | 1 1/2" | 2 5/8" | 9/16" | Steel | 3,750 | 2,700 | 5,900 | Lubricated | -20° to 230° | ABEC-1 | 000000000 | 000000 |
Hex-Bore Ball Bearings
Mount these bearings onto a hex shaft. All have an extended inner ring for additional shaft support. Seals keep out dust and contaminants.
For technical drawings and 3-D models, click on a part number.
Inner Ring | Radial Load Cap., lbs. | ||||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| Bearing Trade Number | For Shaft Wd. | Hex Wd. | For Housing ID | Wd. | OD | Wd. | Ring Material | Dynamic | Static | Max. Speed, rpm | Lubrication | Temp. Range, °F | ABEC Rating | Each | |
Sealed | |||||||||||||||
| 205 | 7/8" | 0.876" | 2.0472" | 0.591" | 1.245" | 1" | Steel | 3,150 | 1,750 | 5,900 | Not Required | -40° to 250° | ABEC-1 | 000000 | 000000 |
Thrust Ball Bearings
Steel balls and washers allow these bearings to handle higher loads than bearings with stainless steel components. With an open design, they dissipate heat more efficiently than one-piece thrust ball bearings.
For technical drawings and 3-D models, click on a part number.
Thrust Load Cap., lbs. | ||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|
| For Shaft Dia. | OD | Thick. | Cage Material | Washer Material | Dynamic | Static | Max. Speed, rpm | Lubrication | Temp. Range, °F | Includes | Each | |
Open | ||||||||||||
| 20mm | 40mm | 14mm | Polyamide Plastic | Steel | 5,000 | 8,400 | 5,900 | Required | -40° to 250° | Two Washers | 00000000 | 000000 |
Needle-Roller Bearings
Also known as drawn-cup roller bearings, these are our thinnest roller bearings. The outer ring is drawn out to form a lip that holds the bearing together. Bearings take on the shape of their housing and may be oblong prior to installation.
Open bearings dissipate heat more efficiently than sealed bearings.
For technical drawings and 3-D models, click on a part number.
Radial Load Cap., lbs. | ||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|
| For Shaft Dia. | For Housing ID | Wd. | Ring Material | Dynamic | Static | Max. Speed, rpm | Lubrication | For Shaft Surface Smoothness (Ra), microinch | Temp. Range, °F | Specifications Met | Each | |
Open | ||||||||||||
| 45mm | 52mm | 12mm | Steel | 3,300 | 6,150 | 5,900 | Required | 8 | -20° to 280° | DIN 618, ISO 3245 | 0000000 | 000000 |
| 45mm | 52mm | 16mm | Steel | 4,750 | 9,650 | 5,900 | Required | 8 | -20° to 280° | DIN 618, ISO 3245 | 00000000 | 00000 |
| 45mm | 52mm | 20mm | Steel | 6,050 | 13,250 | 5,900 | Required | 8 | -20° to 280° | DIN 618, ISO 3245 | 00000000 | 00000 |