With a spherical raceway and two rows of balls, these bearings compensate for shaft misalignment.

Sealed bearings block out dust and other contaminants better than open bearings, but retain more heat.

For technical drawings and 3-D models, click on a part number.

Install these bearings for use with combined radial and thrust loads. They are often used in spindle applications and can be combined with cylindrical roller bearings to better handle radial loads.

Single-row bearings handle thrust loads on one side. For applications with thrust loads on both sides, mount them in pairs.

Double-row bearings handle thrust loads in both directions.

Sealed bearings block out dust and other contaminants better than open and shielded bearings, but retain the most heat.

For technical drawings and 3-D models, click on a part number.

These bearings have twice as many contact points as angular-contact ball bearings. Fit onto large-diameter hollow shafts to run air and hydraulic lines, electrical wiring, and other components through moving parts in assemblies such as index and rotary tables, packaging equipment, and robotics.

Open bearings dissipate heat more efficiently than shielded bearings.

For technical drawings and 3-D models, click on a part number.

Found anywhere from machine tool spindles to conveyor rollers, these bearings have a two-piece design that allows for adjustment.

For technical drawings and 3-D models, click on a part number.

A built-in thrust ball bearing reduces wear from adjacent shaft components, while the needle rollers support high radial loads. Install anywhere you would use separate bearings for radial and thrust loads.

For technical drawings and 3-D models, click on a part number.

Bearings are self-aligning to compensate for shaft misalignment. Seals block out dust and contaminants.

Bearings with a set screw secure to shafts without using a collar. They let shafts rotate in both directions, so they’re good for applications where you need to reverse. However, the set screw will leave some marring on the shaft.

Bearings with eccentric lock have a collar that you twist in one direction to grip and the other to release. Compared to bearings with a set screw, they’re easier to install, require less adjustment over time, and are better for high-speed applications. But, they only work on shafts that spin in one direction.

Bearing with concentric lock use adapter sleeves (sold separately) to lock onto shafts in a way that enables high running speeds with little vibration. They work for applications that require reversing because they allow shafts to rotate in both directions.

For technical drawings and 3-D models, click on a part number.

Bearings are self-aligning to compensate for shaft misalignment. Seals block out dust and contaminants.

Bearings with a set-screw shaft mount secure to shafts with no need for an additional collar. They can be used for bi-directional shaft rotation when applications require reversing action. The set screw may cause some marring on the shaft.

Bearings with an eccentric-lock shaft mount are better than bearings with a set-screw shaft mount for high-speed applications, but only rotate in a single direction.

For technical drawings and 3-D models, click on a part number.

Bearings are self-aligning to compensate for shaft misalignment. Seals block out dust and contaminants.

Set screw bearings secure to shafts as you tighten their screw. They don’t need a collar, but the screw leaves some marring on shafts. Use them in applications where shafts rotate in both directions.

Eccentric lock bearings are quick to install—twist them in one direction to tighten and the opposite to loosen. They’re better than set screw bearings for high speed applications, but they only work with shafts that rotate in one direction.

Concentric lock bearings enable high running speeds while maintaining low levels of vibration; you must pair them with an adapter sleeve (sold separately). They’re good for applications where shafts rotate in both directions.

For technical drawings and 3-D models, click on a part number.

Combine with threaded pipe to mount these bearings in a variety of positions without the need for a flat mounting surface. Bearings are self-aligning to compensate for shaft misalignment. Seals block out dust and contaminants.

NPSM (National Pipe Straight Mechanical) threads are compatible with NPT threads. See more about pipe thread type and sizing.

For technical drawings and 3-D models, click on a part number.