System of Measurement System of Measurement |
|---|
|
For Shaft Diameter For Shaft Diameter |
|---|
|
Bearing Type Bearing Type |
|---|
 | Ball |
Bearing Trade Number Bearing Trade Number | Show |
|---|
|
Bearing Trade Number Bearing Trade Number | Hide |
|---|
For Load Direction For Load Direction |
|---|
 | Radial |
ID ID |
|---|
|
Ball Bearing Type Ball Bearing Type |
|---|
 | With Retaining Ring |
Inner Ring Type Inner Ring Type |
|---|
 | Extended |
Ring Material Ring Material |
|---|
|
Dynamic Radial Load Capacity Dynamic RadialLoad Capacity |
|---|
|
ABEC Rating ABEC Rating |
|---|
|
For Shaft Type For Shaft Type |
|---|
 | Round |
OD OD |
|---|
|
Ball Material Ball Material |
|---|
|
Construction Construction |
|---|
|
DFARS (Defense Acquisition Regulations Supplement) DFARS (Defense AcquisitionRegulations Supplement) |
|---|
Lubricant Lubricant |
|---|
|
Lubrication Lubrication |
|---|
|
About Ball and Roller Bearings
More
Set Screw Collar Ball Bearings
Slip these bearings onto a shaft and secure with the included set screws, no special tools required. All have an extended inner ring for additional shaft support.
Bearings with a black-oxide steel ring have some corrosion resistance.
Shielded bearings dissipate heat more efficiently than sealed bearings.
Bearings with a retaining ring have a removable retaining ring that holds the bearing inside a housing.
For technical drawings and 3-D models, click on a part number.
Inner Ring | Retaining Ring | Radial Load Cap., lbs. | ||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| Bearing Trade Number | For Shaft Dia. | For Housing ID | Wd. | OD | Wd. | OD | Thick. | Dynamic | Static | Max. Speed, rpm | Temp. Range, °F | ABEC Rating | Each | |
Shielded (Lubricated) | ||||||||||||||
Black-Oxide Steel—With Retaining Ring | ||||||||||||||
| ER32 | 2" | 3.937" | 1 3/16" | 2.75" | 2.188" | 4.188" | 0.042" | 10,800 | 6,550 | 3,400 | -40° to 250° | ABEC-1 | 0000000 | 0000000 |
Clamp-On Collar Ball Bearings
Quickly secure these bearings onto shafts with the clamp-on collar for a concentric, mar-free hold. Tighten the single screw on the locking collar around its inner ring on your shaft to center and secure the shaft in the bearing bore. The collar’s firm grip reduces vibration and noise in your system. The steel rings on these bearings have a black-oxide finish for some corrosion resistance.
For technical drawings and 3-D models, click on a part number.
Inner Ring | Retaining Ring | Radial Load Cap., lbs. | |||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| Bearing Trade Number | For Shaft Dia. | For Housing ID | Wd. | OD | Wd. | OD | Thick. | Dynamic | Static | Max. Speed, rpm | Lubrication | Temp. Range, °F | ABEC Rating | Each | |
Sealed | |||||||||||||||
Black-Oxide Steel Ring | |||||||||||||||
| ER32 | 2" | 3 15/16" | 1 3/16" | 2.71875" | 2.1875" | 4.188" | 0.094" | 9,750 | 6,600 | 4,500 | Lubricated | -20° to 220° | ABEC-1 | 0000000 | 0000000 |