System of Measurement System of Measurement |
---|
|
For Load Direction For Load Direction |
---|
![]() | Radial |
![]() | Combined Radial and Thrust |
Width Width | Show |
---|
|
Width Width | Hide |
---|
Static Radial Load Capacity Static Radial Load Capacity |
---|
|
Dynamic Radial Load Capacity Dynamic Radial Load Capacity |
---|
|
Dynamic Thrust Load Capacity Dynamic Thrust Load Capacity |
---|
|
Cage Material Cage Material |
---|
|
Ring Material Ring Material |
---|
|
DFARS (Defense Acquisition Regulations Supplement) DFARS (Defense AcquisitionRegulations Supplement) |
---|
REACH (Registration, Evaluation, Authorization and Restriction of Chemicals) REACH (Registration,Evaluation, Authorization and Restriction of Chemicals) |
---|
|
RoHS (Restriction of Hazardous Substances) RoHS (Restriction ofHazardous Substances) |
---|
|
For Shaft Surface Smoothness (Ra) For Shaft SurfaceSmoothness (Ra) |
---|
|
Maximum Temperature Maximum Temperature |
---|
|
Minimum Temperature Minimum Temperature |
---|
|
Roller Material Roller Material |
---|
|
Shaft Mount Type Shaft Mount Type |
---|
|
Construction Construction |
---|
|
Seal Type Seal Type |
---|
|
About Ball and Roller Bearings
More
About Shaft Collars
Shaft collars are useful for holding and positioning components on a shaft. They can also serve as mechanical stops and stroke limiters.
More
Combination Ball/Needle-Roller Bearings


A built-in thrust ball bearing reduces wear from adjacent shaft components, while the needle rollers support high radial loads. Install anywhere you would use separate bearings for radial and thrust loads.
For technical drawings and 3-D models, click on a part number.
Radial Load Cap., lbs. | Thrust Load Cap., lbs. | ||||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
For Shaft Dia., mm | For Housing ID, mm | Wd., mm | Ball Bearing OD, mm | Ball Bearing Wd., mm | Ring Material | Dynamic | Static | Dynamic | Static | Max. Speed, rpm | Lubrication | For Shaft Surface Smoothness (Ra), microinch | Temp. Range, °F | Each | |
Open | |||||||||||||||
40 | 52 | 32 | 61 | 13 | Steel | 5,350 | 10,600 | 6,045 | 11,240 | 4,500 | Required | 8 | -20° to 230° | 00000000 | 0000000 |
45 | 58 | 32 | 66.5 | 14 | Steel | 5,600 | 11,600 | 6,250 | 12,380 | 4,500 | Required | 8 | -20° to 230° | 00000000 | 000000 |
Needle-Roller Bearings

Also known as drawn-cup roller bearings, these are our thinnest roller bearings. The outer ring is drawn out to form a lip that holds the bearing together. Bearings take on the shape of their housing and may be oblong prior to installation.
Open bearings dissipate heat more efficiently than sealed bearings.
For technical drawings and 3-D models, click on a part number.
Radial Load Cap., lbs. | ||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|
For Shaft Dia. | For Housing ID | Wd. | Ring Material | Dynamic | Static | Max. Speed, rpm | Lubrication | For Shaft Surface Smoothness (Ra), microinch | Temp. Range, °F | Specifications Met | Each | |
Open | ||||||||||||
60mm | 68mm | 32mm | Steel | 11,900 | 30,300 | 4,450 | Required | 8 | -20° to 280° | DIN 618, ISO 3245 | 00000000 | 000000 |
Bearing Retaining Nuts

Often paired with spring lock washers to strengthen their hold, these retaining nuts—also known as shaft nuts—keep vibration from shifting bearings, bushings, pulleys, and gears on your threaded shaft or spindle. They have slotted sides, so you can tighten and loosen them with a spanner wrench or spanner socket. Made of carbon steel, they’re strong and wear resistant.
Use stepped-face retaining nuts with DIN 462 spring lock washers. You can also use them in pairs or with other bearing retaining nuts as jam nuts. For the nut closer to the bearing, position the stepped face towards the bearing. All meet DIN standards for bearing lockout dimensions.
Chamfered-face retaining nuts weigh less and produce less heat than stepped-face nuts. They meet ISO 2982 (formerly DIN 981), an international standard for bearing locknut dimensions. Their sizes correspond to SKF KM series. Use them with DIN 5406 spring lock washers.
For technical drawings and 3-D models, click on a part number.