Built into a terminal block, these switches mount to DIN rail.

Maximize the space in a panel—these switches are half the size of most toggle switches.

These switches meet MIL-S-3950.

Prevent accidental actuation—these toggle switches must be pulled up before they can switch a circuit.

Protect toggle switches from moisture and dust by replacing panel mounting nuts with these rubber covers.

Seal the panel cutout around a toggle switch.

Choose from a variety of messages and colored lenses to combine a rocker with a base and wiring socket for a complete switch.

Rated IP67 for protection from dust and temporary submersion.

Maximize space in a panel—these switches are smaller than most standard rocker switches.

Rated IP67, these switches are protected from temporary submersion.

The built-in contact block in these switches extends behind the panel half the depth of most other 22 mm switches, saving valuable space.

Install in 16 mm dia. cutouts.

Because these switches mount flush against a panel, they're easy to clean and hard to damage.

The face of these switches mounts flush against a panel, so they're easy to clean and hard to damage.

Save space on a panel by using one switch to perform multiple switching functions.

Immediately cut power with a single push.

Also known as tactile switches, these are small enough to fit inside a computer keyboard.

These rubber covers protect switches from splashing liquid.

Operate low-voltage devices that require less than 48 volts, such as doorbells and buzzers.

Install in 14 mm dia. cutouts.

Choose an actuator and contact block to make your own 22 mm plastic switch.

Choose an actuator and contact block to make your own 22 mm metal switch.

More lightweight than steel or stainless steel, these aluminum enclosed switches are rated NEMA 4X for protection from corrosion and washdowns.

Rated NEMA 3S, NEMA 4X, NEMA 13, and IP66, these plastic switches resist corrosion better than aluminum switches and withstand washdowns and oil/coolant spraying.

These aluminum switches are rated NEMA 4, NEMA 13, and IP66 for protection from washdowns and oil/coolant spraying.

Mount these switches in an outlet box. Also known as palm-button switches, they have a large button that makes them easy to use even while wearing gloves.

Often used to trigger alarms, these switches have a recessed button to prevent accidental activation. Mount under desks or in other discrete locations to avoid drawing attention.

Switches are rated NEMA 4, 13, and IP66.

Rated NEMA 4, 13, and IP66, these metal switches are protected from washdowns and oil/coolant spraying. Install them in 30 mm dia. cutouts.

Use these switches where ignitable gas, dust, and fibers may be present. They're UL and C-UL listed for hazardous locations.

A durable rubber housing covers the buttons and protects these switches from impact.

With a slim shape, these switches fit comfortably in your hand.

Operate equipment from up to 330 feet away—these switches include a transmitter and a receiver that connects to equipment.

With a smaller footprint than other switch mats, these fit in confined spaces.

At only 3/32" thick, these mats fit under carpeting or anywhere else you want to hide them.

Customize the length of these switches by cutting them from a 50-foot roll.

Prevent personnel from getting too close to dangerous equipment when equipment is on—these mats turn equipment off when someone steps on them or when a fault is detected.

Turn these switches by hand.

Install these key switches in 3/4" dia. panel cutouts. They require a key to turn circuits on or off, limiting access to sensitive equipment.

Rated NEMA 4, these switches are protected from washdowns.

These 16 mm switches require a key to turn circuits on or off, limiting access to sensitive equipment.

Reset fire panels, or open electromagnetic locks, electric strikes, and automatic door openers. These switches require a key to turn circuits on or off, limiting access and preventing accidental activation.

Safe for use in wet locations, these switches are IP and NEMA rated for protection from corrosion, washdowns, and oil/coolant spraying.

Control equipment from up to 40 feet away—these switches include a transmitter and a receiver that connects to equipment.

When the pedal is pressed, the built-in potentiometer adjusts the resistance to vary the speed for motor drives.

Press these switches with your foot for convenient, hands-free operation.

Connect these switches to a cable to control circuits from a distance. They're typically used to turn off production lines and material handling systems. Equipment will not start up again until switch is manually reset.

The light touch of a finger turns circuits on and off without pressing down a contact.

Transmit a beam of light up to 225 ft. from the transmitter to the receiver.

Scanning 275° side-to-side for people and objects, these switches (known as safety laser scanners) cover large areas and send signals to machinery to prevent accidents.

These switches have a receiver built into the housing, eliminating the need to align components and measure sensing distance during installation.

Rated IP69K, these switches can withstand high-pressure, high-temperature washdowns and temporary submersion.

With a narrow, flat body, these switches fit in tight spaces.

The highly flexible fiber-optic cable and small sensing end help you position these switches in hard to reach areas.

A built-in relay produces AC voltage output. These switches are often used with older programmable logic controllers (PLCs).