These cutters are stainless steel, which provides excellent corrosion resistance.

The grips are a fluorescent color to stand out.

The specially designed internal spring provides constant, uniform tension for superior performance.

These sets include four cutters, each with a different head shape.

These cutters are stainless steel, which provides excellent corrosion resistance.

An alternative to hacksaws and bandsaws, these cutters use leverage to cut rods cleanly in a single stroke.

Insulated handles protect against shock from accidental contact with live electrical circuits. These cutters are tested to 1,000 volts to meet IEC 60900 and ASTM F1505.

These manually operated cutters make a clean cut with just a few pumps of the handle.

Blades are flat on one side for close-to-the-surface cuts.

Split one side of the nut at a time with a nonreplaceable blade.

Make clean cuts on threaded rod with the pull of a trigger.

Keep your hands in a comfortable position so you can apply more force for cutting.

Sharpen or replace the jaws as they wear. These cutters have a double hinge that provides high cutting force with low gripping pressure.

Make repeated cuts in hard materials with cutters that mount for stability and provides extra leverage.

With a quick hammer blow, these cutters make cuts without squeezing or flattening wire.

Also known as nippers, these cutters have wide, flat jaws that cut steel wire and bolts close to the surface.

Cut rods and bolts while leaving their threads intact.

Handle is angled 30° to keep work in sight and hands clear of the work surface. Blades are flat on one side for close-to-the-surface cuts.

Insulated handles protect against shock from accidental contact with live electrical circuits. These cutters are tested to 1,000 volts to meet IEC 60900 and ASTM F1505.

Minimize material distortion while cutting steel and stainless steel wire rope.

A double hinge provides high cutting force with low gripping pressure.

Cut hard steel wire, nails, and small rivets close to the surface with the wide, flat jaws on these cutters.

Turn the handle to make quick and accurate circular cuts.

Cut soft materials such as PTFE, fiber, rubber, and cork.

Produce a clean cut in rope with a cutting blade that pushes down on a flat anvil-style jaw.

A heated blade cuts material and fuses the ends to prevent fraying.

Jaws ratchet to increase cutting pressure as you open and close the handles.

Push the button to cut aluminum and copper power and communication cable.

Use these one-handed cutters on small-diameter aluminum and copper power and communication cable.

Also know as nippers, these pliers have carbide-tipped jaws to break off small pieces of tile for straight cuts.

Make precise, straight cuts in flexible floor tile including asphalt, linoleum, epoxy, and vinyl.

A 12" long blade makes long, straight cuts in thin metals and flexible materials. Not for use on phenolic or other rigid materials.

Turn your workpiece while cutting to create curves and complex shapes.

Also known a scissor-blade shears, the bottom blade remains stationary while the upper blade moves up and down to cut metal up to 1/64" thick with minimal material loss and edge distortion.

Punch small pieces out of material to create an almost burr-free cut with no material distortion.

Also known as slotting shears, these cutters have a double blade that creates two cuts and a 7/32" wide waste strip that peels back, leaving two smooth edges with little distortion.

These nibblers punch small pieces out of material to create an almost burr-free cut with no material distortion.

Make cuts in metal up to 1/32" thick with these compact cutters.

Make round, square, and irregular-shaped holes with this punch-style hole cutter.

Blades are high-speed steel so they stay sharp longer than steel blades, and they can be sharpened.

Made from aluminum bronze, the blade and handle on these cutters inhibit sparking and are FM approved. Use them for straight cuts.

These cutters make straight cuts and curves.

A double hinge provides high cutting force with low gripping pressure. These cutters are also known as aviation snips.

Blades are tapered to give you more control when cutting straight lines, tight curves, and circles, and they're serrated to prevent slipping. These cutters are also known as duckbill snips.

These air-powered cutters include a semi-square blade for no-fray cuts.

Leave clean cut edges in a variety of pliable materials.

A reservoir in the handle provides automatic oil-feed to keep the cutting wheel blade sharp and make cutting easy.