With an oval bushing hole, these lightweight grips secure flat building cable, such as Romex and Festoon cable, in wet areas. All offer strain relief to extend cable life. Made of aluminum, these grips are lighter in weight than steel and brass grips yet durable. They are NEMA and IP rated, so they’ll stand up to dust, oil, washdowns, and temporary submersion in water.

For technical drawings and 3-D models, click on a part number.

Use these lightweight grips to secure cords entering knockouts at a 45° angle in wet, tight spaces while easing the stress from bending. Made of aluminum, they’re lighter in weight than steel and brass grips yet durable. All are NEMA and IP rated, so they’ll stand up to dust, oil, washdowns, and temporary submersion in water.

For technical drawings and 3-D models, click on a part number.

Create a tight grip on cords in wet environments while reducing stress from bending—the 90° angle of these cord grips routes cords to fit tight spaces in enclosures and panels. Made of aluminum, these grips are lighter than steel and brass, yet strong enough to withstand use in demanding environments. A wire mesh extension gives these cord grips extra hold and stability, which reduces the stress of bending and helps extend the lifespan of cords. They’re good for applications with a lot of movement, such as handheld equipment, moving machinery, and robotics. NEMA and IP rated, these cords withstand use under water and protect electronics inside enclosures from moisture, oil, and harsh chemicals.

For technical drawings and 3-D models, click on a part number.

Route cords at a 45° angle when space is tight around enclosures and panels in wet and oily environments. Made of aluminum, these grips are lighter than steel and brass, yet strong enough to withstand use in demanding environments. A wire mesh extension gives these cord grips extra hold and stability, reducing the stress of bending. Because of this, they’re good for applications with a lot of movement, such as handheld equipment, moving machinery, and robotics. NEMA and IP rated, these cords withstand use under water and protect electronics inside enclosures from moisture, oil, and harsh chemicals.

For technical drawings and 3-D models, click on a part number.

These cord grips are lightweight yet durable. As you tighten the grip, a nylon inner ring and lubricated rubber bushing secure your cable, prevent overtightening, and create a seal around the cord to block out liquid. The inner rings are colored by size so you can identify them at a glance.

Locknut and O-ring kits (sold separately) create liquid-tight seals between cord grips and enclosure knockouts. Rated NEMA 4X, NEMA 13, and IP66, the resulting seals provide indoor and outdoor protection against dust, corrosion, water projected from a hose, and oil/coolant spray. Each kit includes two locknuts and one or two O-rings.

For technical drawings and 3-D models, click on a part number.

Secure and seal electrical cords entering knockouts at a 45° angle. As you tighten these grips, a nylon inner ring and lubricated rubber bushing secure the cords to keep them connected and prevent overtightening. They also create a seal around the cords to block out liquids. Made of aluminum, all of these grips are lighter in weight than steel grips yet durable.

Optional locknut and O-ring kits create liquid-tight seals between cord grips and enclosure knockouts. The seals protect your connection from dust, water, oil, and coolant. Each kit includes two locknuts and one or two O-rings.

For technical drawings and 3-D models, click on a part number.

A mesh extension provides a secure hold in applications where cable is pulled or in motion. It reduces stress on the cable and prevents kinking for longer cable life. A plastic bushing seals out dust and dirt.

For technical drawings and 3-D models, click on a part number.

These cord grips are lightweight yet durable. They have a zinc-plated steel locknut and metal-reinforced rubber O-ring that prevents liquid from entering the connection. All are rated NEMA 4X, NEMA 13, and IP66 to provide indoor and outdoor protection against dust, corrosion, water projected from a hose, and oil/coolant spray.

Grips have a knurled collar for hand tightening. As you tighten the grip, a nylon inner ring and lubricated rubber bushing secure your cable, prevent overtightening, and create a seal around the cord to block out liquid. The inner ring is colored by size, so you can identify the grips’ size at a glance.

For technical drawings and 3-D models, click on a part number.

These cord grips are lightweight yet durable. They have a zinc-plated steel locknut and metal-reinforced rubber O-ring that prevents liquid from entering the connection. All are rated NEMA 4X, NEMA 13, and IP66 to provide indoor and outdoor protection against dust, corrosion, water projected from a hose, and oil/coolant spray.

Grips have a knurled collar for hand tightening. As you tighten the grip, a nylon inner ring and lubricated rubber bushing secure your cable, prevent overtightening, and create a seal around the cord to block out liquid. The inner ring has an insert that is colored by size, so you can identify them at a glance.

For technical drawings and 3-D models, click on a part number.

Secure cords in wet and industrial environments with little room—these grips curve 45° to relieve bending stress. Made of aluminum, they’re lighter in weight than steel yet strong enough for harsh applications. All are NEMA and IP rated, so they stand up to weather, washdowns, dirt, dust, oil, and coolant.

A nylon insert and rubber bushing on these grips stop cords from coming loose and seal out liquid. They also prevent you from overtightening the grip and cutting into the cord’s sheath. A zinc-plated steel locknut and rubber O-ring keep water from seeping into your enclosure.

For technical drawings and 3-D models, click on a part number.

These grips meet Class III, Divisions 1 and 2 standards for use in hazardous locations. They have a mesh extension for a secure hold in applications where cable is pulled or in motion. It reduces stress on the cable and prevents kinking for longer cable life.

For technical drawings and 3-D models, click on a part number.

These grips meet Class III, Divisions 1 and 2 standards for use in hazardous locations. They have a mesh extension for a secure hold in applications where cable is pulled or in motion. It reduces stress on the cable and prevents kinking for longer cable life.

For technical drawings and 3-D models, click on a part number.

Grips have a rubber inner grommet with multiple holes and a rubber O-ring that create a tight seal to prevent liquid from entering the connection. They are rated IP65 for protection from water projected from a nozzle and NEMA 4X for indoor and outdoor protection against corrosion and water projected from a hose.

Nylon is chemical resistant.

For technical drawings and 3-D models, click on a part number.

These grips have a thin, flexible seal that covers the holes until you push cords through. They prevent liquid from entering your connections—grips are rated IP68 for protection from continuous submersion.

For technical drawings and 3-D models, click on a part number.