Excellent chemical resistance makes these PTFE plastic feet the best choice for harsh environments.

Peel back the film to stick these feet to the bottom of furniture and equipment legs.

An integral cushion reduces noise and vibration.

Screw these feet to the bottom of wood furniture legs.

These feet have angled or rounded bottoms to work with tubular furniture legs that meet the floor at an angle.

A swiveling base compensates for angled legs and uneven surfaces.

These mounts have a cushion on top to provide padding between your furniture and the mount.

Made entirely of plastic, these mounts are resistant to oil and won't scratch your mounting surface.

Use these metric mounts on heavy machines and equipment.

Protect surfaces from scratches and wear.

Often used on wobbly tables, these mounts automatically adjust up to 5/16" to compensate for uneven floors.

Able to withstand temperatures up to 350° F, these have the highest maximum temperature of our plastic mounts.

Punch-out holes in the base let you bolt down these mounts to keep your equipment stationary.

Black-oxide steel has a dull shine for areas where appearance is a concern.

An economical choice for applications in corrosive environments that don't require high load capacities, these mounts have a plastic base.

Made of 303 stainless steel, these mounts resist corrosion from water and most chemicals.

Yellow zinc-plated steel is more corrosion resistant than nickel-plated steel.

Punch-out holes in the base let you bolt down these mounts to keep your equipment stationary.

Well-suited to damp environments, these mounts have a stainless steel stud and nut for corrosion resistance.

Made of yellow zinc-plated steel, these metric leveling mounts are more corrosion resistant than nickel-plated steel leveling mounts.

An offset mounting hole allows for installation without moving your machine.

Punch-out holes in the base let you bolt down these metric mounts to keep your equipment stationary.

Made of 303 stainless steel, these metric mounts resist corrosion from water and most chemicals.

Made entirely of 316 stainless steel, these metric mounts have superior corrosion resistance.

Reinforced with fabric so extreme compression won’t deform them, these pads protect surfaces from impact, dampen vibration and noise, and act as stable connection points. They’re commonly known as bearing pads.

Place pads under equipment, such as drill presses, milling machines, saws, and air-conditioning units to minimize vibration and noise transmitted to and from machinery.

These soft pads work well for isolating vibration with light loads such as lab and testing equipment.

Able to shoulder up to 1,500 psi per mounting point, nitrile pads can support heavy machinery.

Made of fiber-reinforced PVC, these pads endure exposure to corrosive chemicals, such as cleaning solvents, chlorine, and hydrochloric acid.

The polyurethane base on these mounts resists solvents, gasoline, and oil, while the metal plate sustains heavy loads.

Made of neoprene rubber, these mounts are oil resistant, so they're good for use under generators, HVAC equipment, electric motors, pumps, and blowers.

These mounts withstand exposure to weather and resist oil, antifreeze, and other petroleum-based fluids.

Made of nitrile rubber, these mounts are oil resistant for use in compression load applications with punch presses, milling machines, grinders, and air compressors.

Connect these mounts to your air supply for vibration and shock isolation in compression load applications.

All-stainless steel construction stands up to water and chemicals and won't rust or corrode.

Higher deflection ratings translate to greater vibration and shock isolation than our other vibration-damping leveling mounts.

Choose from mounts that support 3,000 to 30,000 lbs. for heavy machinery.

Thread these mounts into machinery to level them on uneven floors in sanitary environments such as food-processing areas.

Higher deflection ratings translate to greater vibration and shock isolation.

These mats have a smooth backing for use on hard floor surfaces.

Press these bumpers into place with the adhesive backing. Use them as feet and spacers on instruments and small appliances to limit sliding, vibration, and noise. They're comparable to Bumpon bumpers.

Select these bumpers for applications that require specific load capacities. Use them as feet and spacers on instruments and small appliances to limit sliding, vibration, and noise. Press them into place with the adhesive backing. They're comparable to Bumpon bumpers.

All of these bumpers are reinforced with an embedded washer or base plate for strength. Often used as feet, spacers, and vibration dampers, they absorb shock to prevent damage to equipment and surfaces. They're also good for starting and stopping motion on automated machines. Install them with screws.

Install these bumpers with screws. Often used as feet, spacers, and vibration dampers, they absorb shock to prevent damage to equipment and surfaces.

These bumpers are at a 90° angle to protect corners on equipment, walls, and docks from damage caused by carts, vehicles, and other moving objects. Install them with screws.

Mount these bumpers on a threaded stud. All are reinforced with a steel core or base plate for strength. Often used as feet, spacers, and vibration dampers, they absorb shock to prevent damage to equipment and surfaces. They're also good for starting and stopping motion on automated machines.

A ridge on the stem provides a tighter grip than other push-in bumpers. Push the stem into a hole for quick installation. These bumpers are commonly used as feet on instruments and bench-top equipment to keep them from sliding. They're also good as spacers between sheets of material. Also known as stem and grommet bumpers.

Select these bumpers for applications that require specific load capacities. All are reinforced with a base plate for strength. Often used as feet, spacers, and vibration dampers, they absorb shock to prevent damage to equipment and surfaces. They're also good for starting and stopping motion on automated machines and conveyors. Mount these bumpers on a threaded stud.

All of these bumpers are reinforced with a steel core for strength. Often used as feet, spacers, and vibration dampers, they absorb shock to prevent damage to equipment and surfaces. They're also good for starting and stopping motion on automated machines. Twist them into a threaded hole.

The stem on these bumpers compresses to fit into tight holes. Push the stem into a hole for quick installation. These bumpers are commonly used as feet on instruments and bench-top equipment to keep them from sliding. They're also good as spacers between sheets of material. Also known as stem and grommet bumpers.

Make any hard seat more comfortable with these foam-padded cushions.

This synthetic felt is an economical alternative to wool felt.

Line toolboxes and drawers to cushion and protect small parts.

Use these round shims as they are, or punch out the middle to create the ID you need.