Flatten these carboys for convenient storage.

Fill these air-and liquid-tight bottles directly from your line to store, test, and ship liquids. Connect to a quick-clamp fitting with the included gasket and clamp.

Transfer liquid through tubing.

The open top makes these easier to fill than jugs, while the spout gives more control when pouring.

Also known as Type I safety cans, these have a single opening for both filling and pouring.

Tip cans down for controlled dispensing, then swing them back to their upright position.

Made of plastic to resist harsh acids and corrosives, these safety cans have a self-closing cap to prevent spills and a trigger handle to empty contents with one hand.

Easily fill these cans through the detachable wide-mouth funnel, then remove the threaded plug to empty. A flame arrester protects against outside ignition.

These tote boxes resist most chemicals, solvents, and oils.

With a capacity of 500 lbs., these are the strongest bin boxes we offer.

These bottles are fluorinated to prevent contents from being absorbed.

These bottles are made with an additive that prevents electrostatic discharge from building up on the surface.

These bottles are made with an additive that prevents electrostatic discharge from building up on the surface.

Long nozzles allow dispensing in hard-to-reach places.

Spray thin liquids evenly without propellant. Fill the sprayer and pressurize with compressed air.

These sprayers are small enough to use with one hand.

Pump the handle to pressurize the tank, then squeeze the trigger on the wand to spray. These sprayers are often used for degreasers, insecticides, disinfectants, cleaning solutions, and herbicides.

Carry these sprayers comfortably on your back using the padded shoulder straps.

No hand pumping necessary—use these electric-powered sprayers to disinfect surfaces and equipment in bathrooms, schools, gyms, and worksites.

The nozzle on these foamers injects air to make cleaners and disinfectants foam as you spray them.

Disinfect bathrooms, desks, doors, and other small areas and items with these portable sprayers.

Release a fine mist spray similar to an aerosol without propellants or pressure.

These spray bottles resist harsh chemicals and solvents.

Spray liquids around your food processing plant while reducing the risk of contaminating the food. These spray bottles have metal additives in the spray head and on the label that can be picked up by a metal detector if the bottles—or any piece of the spray head or label—fall into your line.

Access tight spaces with the 36" long tube that extends from these spray bottles.

Unlike standard spray bottles, these dispense oil and other high-viscosity liquids without clogging.

An additive prevents electrostatic discharge from building up on the surface of these dispensers.

Turn these bottles upside down and press the flange to dispense.

Squeeze the ball to create pressure, then push down on the dispenser to dispense flammable liquids into vials, test tubes, and other small containers. Only a PTFE tube and stainless steel pump come into contact with the liquid.

Also known as basters, these dispensers transfer larger amounts of liquid than bulb droppers. Liquids are dispensed in a stream, rather than drop by drop.

Cover the top opening with your thumb to control the flow of liquid one drop at a time.

Store up to five micropipettes in these racks.

Use these glass pipettes with pipette pumps.

More precise than pipettes, burettes have a stopcock that allows you to release exact amounts of liquid.

Prevent the absorption of harsh solvents, cleaning agents, and adhesives to safely ship hazardous liquids. There is a security ring on the lid that separates when the jug is opened.

The jug in these kits holds its shape as liquid is dispensed. It comes with a cardboard box for protection.

Drain and transfer liquid more quickly and easily than hand-operated pumps and siphon pumps.

These pumps quickly empty drum contents by moving 48 gallons of liquid per minute. Their electric motors are UL listed for use in environments with flammable gases and combustible dust.

For accurate dispensing in extremely low-flow applications, these pumps allow you to adjust flow in 2% increments.

These pumps are rated for fuel such as gasoline, kerosene, and diesel fuel.

Extract water from valve boxes, meter pits, and other small spaces.

Push the plunger to pump water, cleaners, and chemicals.

Rotate the handle to dispense a continuous flow of liquid.

Remove liquid from hard-to-reach areas with a long, flexible intake tube that extends into deep and hard-to-access tanks.

Since these pumps use suction to draw liquid out of your container, they continue dispensing once you get them started.

The foot pedal allows hands-free operation.

Transfer lubricating oil such as hydraulic and motor oil with these pumps. They handle nearly twice the amount of pressure as other air-powered drum pumps to move high-viscosity liquids.

A filter/lubricator ensures efficiency and reduces wear on the pump. Often used with hydraulic oil and motor oil in addition to acidic and alkaline liquids, these pumps have a nonsparking motor for use in applications where electricity is unavailable or dangerous.

A stainless steel construction allows these pumps to be used with aggressive chemicals such as methyl ethyl ketone and xylene.

For easy cleaning, these pumps have a sanitary quick-clamp discharge connection. They're made of FDA listed materials for use with food, water, and beverage.

Pump fuel such as gasoline, kerosene, and diesel fuel.

Often used with ammonia, etching and cleaning solutions, and other caustics, these pumps have a nonsparking air-powered motor for applications where electricity is unavailable or dangerous.

Since these pumps move liquid by pressurizing your drum, they have few moving parts prone to wear and tear.

These pumps have a motor that is rated for IEC Zone 1, Groups IIB and IIA; and IEC Zone 21, Groups IIIC, IIIB, and IIIA hazardous locations with flammable gases and vapors, so they can be used with liquids such as acetone, ethanol, methyl ethyl ketone, xylene, and mineral spirits.

A nozzle and hose allow you to dispense directly into your container. For on-site diesel fuel dispensing at construction sites, on boats, and in other environments without electrical hookups, attach these portable pumps to any 12-volt battery.

Operating on a 12-volt battery, use these pumps to transfer and drain fuel such as gasoline, diesel fuel, and kerosene.

Also known as peristaltic pumps and tubing pumps, these maintain a fixed flow rate.

Install these pumps in a panel cutout. Often used in food and beverage, pharmaceutical, and lab applications, they dispense small amounts of liquid at a set rate.

An adjustment dial with a locking lever allows for easy flow control. Also known as diaphragm metering pumps, these can be used with pressures up to four times higher than standard pumps for chemicals.

Automatically control output from a distance using 4‐20 mA or external-pulse signals. These pumps meter a consistent amount of liquid within ±2% of the maximum flow.

Automatically control output from a distance using variety of analog and digital signals, including 4-20mA and external pulse signals.

A 316 stainless steel housing provides corrosion resistance for a long life in harsh environments. These pumps meter a consistent amount of liquid within ±2% of the maximum flow.

An adjustment screw lets you increase or decrease flow rate without the hassle of changing tubing. Often used in boiler feed systems and water treatment, these pumps are compatible with chemicals such as cleaning fluids and acid-washing solutions.

This pump has a totally enclosed nonventilated (TENV) motor that is cooled by the liquid being pumped. Also known as a flexible impeller pump, it creates a suction force that can draw liquid upward to fill the pump chamber when your liquid source is below the pump.

A cast iron housing and steel gears allow these pumps to be used with hydraulic and motor lubricating oil. Also known as gear pumps, they produce a smooth flow of liquid for applications such as engine lubrication.

Rated for continuous use, these pumps are often used to move caustics such as antifreeze and salt water. Mount them in any position, even upside down. Also known as diaphragm pumps, they are typically used for low-flow spraying, draining, and washdown applications.

An aluminum enclosure around the motor provides protection in dusty and dirty environments. Designed to fit into small equipment, these pumps have miniature gears and a subfractional horsepower motor for low-flow applications.

These pumps have a PTFE diaphragm compatible with oil, fuel, and chemicals such as mineral spirits, methyl ethyl ketone (MEK), and xylene. They have a rugged aluminum housing for moving large volumes of thick sludges and slurries in demanding environments.

Resistant to chemicals such as ammonia, detergents, and cleaning fluids, these pumps have a Santoprene diaphragm and polypropylene housing. Pumps can be used to move thick sludges and slurries

A neoprene diaphragm stands up to oil and chemicals such as isopropyl alcohol and deionized water. These pumps have large internal pathways and check valves with flaps to accommodate thick sewage, abrasive slurries, and industrial waste with large solids that would damage standard air-powered transfer pumps.

Absorb pulsation caused by air-powered transfer pumps, reducing wear and preventing damage to inline components such as regulators, sensors, and gauges.

With a 316 stainless steel housing and a PTFE diaphragm, these pumps resist a variety of acids, alkalies, and flammable liquids such as phosphoric acid, acetone, and methyl ethyl ketone (MEK). They're designed for moving large volumes of thick sludges and slurries in demanding environments.

Also known as sprayer pumps, these provide a smooth, uniform flow for agricultural spraying, soap dispensing, and chemical transferring.

Small enough to fit in the palm of your hand, these pumps transfer water, detergents, and chemicals.

With all PTFE wetted parts, these pumps offer the best chemical resistance of all our air-powered transfer pumps and can handle solvents and petroleum-based fluids that PVDF pumps can’t.

A Buna-N diaphragm stands up to lubricating oil such as hydraulic and motor oil. These pumps are designed to handle thick sludges and slurries.

Store harsh, nonflammable liquids in these plastic cabinets—even acid vapors won't corrode them.