Use these metal dowel pins as pivots, hinges, shafts, jigs, and fixtures to locate or hold parts.

Slip these pins in and out during maintenance or prototyping—they’re undersized to make alignment easier.

Cut this 12" stock to the length you need.

The flat side of these pins relieves trapped air, making them easier to insert in and remove from blind holes. To remove, thread a screw or tool into the tapped hole, then pull the pin out.

Center-groove pins are often used in place of clevis pins or to create T-handles. The grooved center locks pins in position, while the smooth ends act as a pivot. Also known as type E pins.

Grooves run the full length of these pins for a firm hold that won't spin. Use them in place of standard dowel, spring, and taper pins to fasten parts. Also known as type A pins.

These pins are commonly used as anchors for tension springs. The grooved half locks pins in position, and spring ends fit in to the notch. Also known as type G pins.

Join two pieces of wood with these dowel pins. When glued, they expand for a tight fit.

The full length of these pins is knurled for a tight grip that won't spin.

Made of compressed wood, these biscuits fit into slots cut into wood. When glued, they expand for a tight fit.

Use these pins to fasten components made of soft materials such as plastic or aluminum. Opposing barbs bite into each piece, pulling them together for a tight, secure fit.

For use with Browning shear hubs, these pins are designed to fail at specific loads to protect heavy duty machinery from torque overload.

A 60° beveled head fits into a countersunk hole.

A thick shoulder makes these pins more rigid than standard ejector pins.

Also known as roll, tension, split, and expansion pins, these pins have a slot along one side that you squeeze closed to install them into unthreaded holes.

These spiral pins remain flexible after installation, so they absorb shock and vibration better than slotted spring pins. They work well in holes that are out of round.

To remove these pins, hit the small end with a punch to drive the pin out.

These internally threaded pins sit flush in an assembly. For easy removal from a blind hole, thread a screw into the pin and pull out.

Create a custom headed pin with your choice of material, dimensions, and end type.

Screw these studs into a tapped hole and use them as a pivot point, hinge, shaft, or locator pin.

Dowel pins are commonly used as pivots, hinges, shafts, jigs, and fixtures to locate or hold parts. They're slightly oversized for a tight fit.

Install these pins in a plate or table and mate with holes in a workpiece for precise alignment.

The shoulder provides a consistent height reference point and keeps the pin from being pressed through the fixture.

A slightly undersized shank makes these pins easy to install and replace. Also known as slip-fit and lock-screw locating pins, they are held in place by a separate lock screw.

Precisely align drilled holes in two parts.

The head on these pins slides side-to-side in one direction. Use one of these pins and one standard round-head pin to prevent jamming when loading and unloading workpieces with inconsistent hole spacing.

Support and position workpieces and fixtures from the bottom or side. These buttons press into a drilled hole for permanent installation.

Use these buttons to support and position workpieces and fixtures from the bottom or side. Their hex shape lets you screw them into a threaded hole with a wrench or socket.

As the workpiece pushes against the pin head in one direction, the internal spring pushes back to hold it in place for clamping.

Threading makes these guide pins easier to remove and replace than press fit, so they're useful for high-wear applications.

As the face of these plungers is pushed in, the internal spring applies outward pressure to hold a workpiece in position against stops and rails.

Line up holes by driving these pins through existing rivet, pin, and bolt holes in multiple pieces of metal. Alternatively known as lineup taper punches.

These brass tools reduce marring on metal surfaces because they're softer than steel punches.

Made from aluminum-bronze that is Factory Mutual approved, these nonmagnetic, corrosion-resistant tools inhibit sparking. They satisfy OSHA requirements for nonsparking tools.

Often called bull pins, these pins are designed to resist mushrooming caused by repeated pounding.

Use alignment pins to align structural components such as I-beams and angle iron for bolting, riveting, and welding.