Drill holes using simultaneous rotary and hammering action to break masonry material into tiny granules. These bits drill faster and penetrate materials with less pressure than rotary-only bits. Also known as percussion or impact bits.

For technical drawings and 3-D models, click on a part number.

The SDS-Max shank has three deep slots and two shallow slots for use with SDS-Max-drive rotary hammers. These bits cannot be used with SDS-Plus-drive rotary hammers. Drill holes using simultaneous rotary and hammering action to break masonry material into tiny granules. This type of bit drills faster and penetrates material with less pressure than rotary-only bits. Also known as percussion or impact bits.

Multi-point drill bits have five carbide points on the tip, which provide longer life and reduce vibration for drilling smoother, rounder holes than standard-point masonry drill bits.

For technical drawings and 3-D models, click on a part number.

Instead of using a hammering action to break up masonry material, these bits drill with rotary action only, requiring more pressure to grind up material. Use with handheld power drills, drill presses, and in hammer drills set to rotary-only mode. Do not use in hammering applications.

When using bits with a maximum drilling depth of 10 1/2” or greater, take the bit out of the hole every 4” and remove debris before drilling deeper to achieve maximum drilling depth.

For technical drawings and 3-D models, click on a part number.

Each bit is precisely sized to match the tolerances necessary to achieve maximum holding strength from tapping screws. The SDS-Plus shank has two deep slots and two shallow slots for use with SDS-Plus-drive rotary hammers. These bits cannot be used with SDS-Max-drive rotary hammers.

For technical drawings and 3-D models, click on a part number.

When you encounter rebar, stop drilling and mount one of these bits in your tool. Drill through the rebar, and then resume drilling with your masonry drill bit. The SDS-Plus shank has two deep slots and two shallow slots for use with SDS-Plus-drive rotary hammers set to rotary-only mode. These bits cannot be used with SDS-Max-drive rotary hammers. Do not use in hammering applications.

For technical drawings and 3-D models, click on a part number.

When you encounter rebar, stop drilling and mount one of these bits in your tool. Drill through the rebar, and then resume drilling with your masonry drill bit. These bits drill holes using rotary action only and should not be used in hammering applications. Use with handheld power drills, drill presses, and in hammer drills set to rotary-only mode.

For technical drawings and 3-D models, click on a part number.

When connected to a vacuum, these hollow bits can suck up concrete dust while drilling to help meet OSHA standards for silica dust exposure. They can also be used to clean out holes for installing adhesive anchors. The SDS-Max shank has three deep slots and two shallow slots for use with SDS-Max-drive rotary hammers. They cannot be used with SDS-Plus-drive rotary hammers.

Bore clean, flat bottom holes in soft wood, veneer, and laminates. The center guide point prevents the bit from wandering. Also known as Forstner bits.

Carbide-tipped steel drill bits maintain their sharp edges longer than alloy tool steel bits, and can cut through tough, abrasive material such as plywood, hard wood, and composites.

For technical drawings and 3-D models, click on a part number.

Multiple outlining teeth bore clean, flat-bottom holes without chipping or splintering your surface—even when cutting across the grain. These bits are excellent for boring straight holes, overlapping holes, and holes on close centers in soft wood, veneer, and laminates. The center guide point prevents the bit from wandering. Also known as multispur bits or Forstner bits.

For technical drawings and 3-D models, click on a part number.

Also known as spade bits, these have a centering point and two cutting edges for boring holes in hard and soft wood.

For technical drawings and 3-D models, click on a part number.

Steps with progressively larger diameters let you drill a range of sizes with one bit. Also known as step drills.

Black-oxide drill bits produce less friction than uncoated drill bits.

Titanium-nitride (TiN) coated drill bits last longer and can drill at higher speeds than uncoated drill bits and black-oxide drill bits.

For technical drawings and 3-D models, click on a part number.

With better heat and wear resistance than high-speed steel, cobalt steel bits can run up to 25% faster and have a longer tool life. Steps with progressively larger diameters let you drill a range of sizes with one bit. Also known as step drills.

For technical drawings and 3-D models, click on a part number.