System of Measurement System of Measurement |
|---|
|
Decimal Size Equivalent Decimal Size Equivalent | Show |
|---|
|
Decimal Size Equivalent Decimal Size Equivalent | Hide |
|---|
For Use On For Use On |
|---|
|
Shank Type Shank Type |
|---|
 | SDS Max |
 | Spline |
 | Threaded Hub |
Thread Size Thread Size |
|---|
Shank Size Shank Size |
|---|
|
Point Style Point Style |
|---|
 |
| Standard |
For Drilling Type For Drilling Type |
|---|
|
DFARS (Defense Acquisition Regulations Supplement) DFARS (Defense AcquisitionRegulations Supplement) |
|---|
Bit ID Bit ID |
|---|
|
Bit Style Bit Style |
|---|
 | Hollow |
Individual/Set Individual/Set |
|---|
|
Finish Finish |
|---|
|
RoHS (Restriction of Hazardous Substances) RoHS (Restriction ofHazardous Substances) |
|---|
|
Flute Direction Flute Direction |
|---|
 |
| Right Hand |
Specifications Met Specifications Met |
|---|
Point Angle Point Angle |
|---|
|
Component Component |
|---|
|
Drill Bit Decimal Size Equivalents
More
About Drill Bits
More
About Masonry Drill Bits
More
Changeable-Size SDS-Max-Shank Masonry Core Drill Bits for Rotary Hammers
These bits allow you to switch to another size by changing only the bit body. They are hollow and cut with their outside edge for drilling large holes. The SDS-Max shank has three deep slots and two shallow slots for use with SDS-Max-drive rotary hammers. They cannot be used with SDS-Plus-drive rotary hammers.
Drill holes using simultaneous rotary and hammering action to break masonry material into tiny granules. This type of bit drills faster and penetrates material with less pressure than rotary-only bits. Also known as percussion or impact bits. To achieve maximum drilling depth, break up and remove the core every 4” before drilling deeper.
Drill bits include a pilot drill to make starting holes easier.
For technical drawings and 3-D models, click on a part number.
| Size | Decimal Size Equivalent | Overall Lg. | Max. Drilling Dp. | Shank Type | Point Style | Specifications Met | For Use On | Includes | Each | |
Uncoated Carbide-Tipped Steel | ||||||||||
|---|---|---|---|---|---|---|---|---|---|---|
| 4" | 4" | 17" | 12" | SDS Max | Standard | ANSI B212.15 | Masonry, Concrete | Pilot Drill | 00000000 | 0000000 |
| Size | Decimal Size Equivalent | Overall Lg. | Material | Specifications Met | Each | |
| 4" | 4" | 5" | Uncoated Carbide-Tipped Steel | ANSI B212.15 | 0000000 | 0000000 |
SDS-Max-Shank Masonry Core Drill Bits for Rotary Hammers
These hollow bits cut with their outside edge for drilling large holes. The SDS-Max shank has three deep slots and two shallow slots for use with SDS-Max-drive rotary hammers. They cannot be used with SDS-Plus-drive rotary hammers. Drill holes using simultaneous rotary and hammering action to break masonry material into tiny granules. This type of bit drills faster and penetrates material with less pressure than rotary-only bits. Also known as percussion or impact bits. The included pilot drill makes starting holes easier.
22" Overall Lg. | |||||||||
|---|---|---|---|---|---|---|---|---|---|
| Size | Decimal Size Equivalent | Shank Type | Point Style | Specifications Met | For Use On | Includes | Max. Drilling Dp. | Each | |
Inch | |||||||||
Uncoated Carbide-Tipped Steel | |||||||||
| 4" | 4" | SDS Max | Standard | ANSI B212.15 | Masonry, Concrete | Pilot Drill, Core Ejector Key | 17" | 00000000 | 0000000 |
| Replacement Pilot Drill with Core Ejector Key | 00000000 | Each | 000000 |
Changeable-Size Spline-Shank Masonry Core Drill Bits for Rotary Hammers
These bits allow you to switch to another size by changing only the bit body. They are hollow and cut with their outside edge for drilling large holes. The shank has 12 splines for use with a spline-drive rotary hammer. Drill holes using simultaneous rotary and hammering action to break masonry material into tiny granules. This type of bit drills faster and penetrates material with less pressure than rotary-only bits. Also called percussion or impact bits.
Drill bits include a pilot drill to make starting holes easier.
For technical drawings and 3-D models, click on a part number.
| Size | Decimal Size Equivalent | Overall Lg. | Max. Drilling Dp. | Shank Type | Point Style | Specifications Met | For Use On | Includes | Each | |
Uncoated Carbide-Tipped Steel | ||||||||||
|---|---|---|---|---|---|---|---|---|---|---|
| 4" | 4" | 17" | 12" | Spline | Standard | ANSI B212.15 | Masonry, Concrete | Pilot Drill | 00000000 | 0000000 |
| Size | Decimal Size Equivalent | Overall Lg. | Material | Specifications Met | Each | |
| 4" | 4" | 5" | Uncoated Carbide-Tipped Steel | ANSI B212.15 | 0000000 | 0000000 |
| For Drill Bit Size | Material | Each | |
| 1 1/2", 1 3/4", 2 1/2", 2", 3 1/2", 3", 4 1/2", 4", 5" | Carbide-Tipped Steel | 0000000 | 000000 |
Masonry Drill Bits for Drilling Rigs
Use these diamond-coated hollow bits for wet drilling of masonry, concrete, and rebar with a drilling rig. They're not for dry drilling or use with portable electric drills or grinders. The size listed is the bit’s OD.
Shank | |||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|
| Size | Decimal Size Equivalent | Bit ID | Overall Lg. | Max. Drilling Dp. | Thread Size | Type | Size | Point Style | For Use On | Each | |
Diamond-Coated Steel | |||||||||||
| 4" | 4" | 3 3/4" | 15 1/2" | 13" | 1 1/4"-7 | Threaded Hub | 4" | Standard | Masonry, Concrete, Reinforced Concrete, Rebar | 0000000 | 0000000 |