These jobbers'-length bits have the rigidity and length required for most applications. The flutes are designed to lift chips out of the hole, reducing clogging and improving coolant flow.

Parabolic spiral flute drill bits have wider flutes for more efficient chip evacuation than spiral-flute bits.

Black-oxide drill bits produce less friction than uncoated drill bits.

Titanium-nitride (TiN) coated drill bits last longer and can drill at higher speeds than uncoated and black-oxide drill bits.

Drill bits with a split point keep centered without a pilot hole.

For technical drawings and 3-D models, click on a part number.

These jobbers'-length bits have the rigidity and length required for most applications. Made of cobalt steel, which has better heat and wear resistance than high-speed steel, they can run up to 25% faster and have a longer tool life.

Titanium-nitride (TiN) coated drill bits last longer and can drill at higher speeds than uncoated drill bits.

Drill bits with a split point keep centered without a pilot hole.

For technical drawings and 3-D models, click on a part number.

These jobbers'-length bits have the rigidity and length required for most applications. Made of solid carbide for the highest accuracy and longest tool life, they are harder, stronger, and more wear resistant than high-speed steel, cobalt steel, and carbide-tipped bits. They retain a sharp, hard edge at high temperatures for the best performance on hard and abrasive material. The four-facet point keeps the bit centered without a pilot hole. These bits require rigid toolholding to prevent breakage and should not be used in hand-held drilling applications.

Titanium-nitride (TiN) coated drill bits last longer and can drill at higher speeds than uncoated drill bits.

Titanium-aluminum-nitride (TiAlN) coated drill bits are the most wear and temperature resistant for the longest life and highest drilling speeds.

For technical drawings and 3-D models, click on a part number.

Three cutting edges instead of the typical two enable these bits to drill holes with a smoother finish than other bits. Made of solid carbide for the highest accuracy and longest tool life, they are harder, stronger, and more wear resistant than high-speed steel, cobalt steel, and carbide-tipped bits. They retain a sharp, hard edge at high temperatures for the best performance on hard and abrasive material. These bits require rigid toolholding to prevent breakage and should not be used in hand-held drilling. All are jobbers’ length so they have the rigidity and length required for most applications. A split point keeps the bit centered without a pilot hole.

For technical drawings and 3-D models, click on a part number.

Holes in these bits allow coolant to be run through the tool for more efficient chip evacuation. Use them in CNC machines with coolant-through technology. Made of solid carbide for the highest accuracy and longest tool life, they are harder, stronger, and more wear resistant than high-speed steel, cobalt steel, and carbide-tipped bits. They retain a sharp, hard edge at high temperatures for the best performance on hard and abrasive material. A titanium aluminum nitride (TiAlN) coating gives them additional wear and temperature resistance. The four-facet point keeps the bit centered without a pilot hole. These bits require rigid toolholding to prevent breakage and should not be used in hand-held drilling applications.

Jobbers'-length drill bits have the rigidity and length required for most applications.

For technical drawings and 3-D models, click on a part number.

These jobbers'-length bits have the rigidity and length required for most applications. Made of carbide-tipped steel, which has better wear resistance than high-speed steel and cobalt steel, they maintain a sharper, harder edge at high temperatures for excellent performance on abrasive material, such as plastic. Because they aren’t as brittle as solid carbide bits, they can be used in less rigid setups, such as a hand-held drill.

Drill bits with a split point keep centered without a pilot hole.

Drill bits with 135° point angle produce smaller chips than 118° point to prevent clogging.

For technical drawings and 3-D models, click on a part number.

The shank has a smaller diameter than the tip, allowing you to drill large holes with machines that have small-capacity chucks.

For technical drawings and 3-D models, click on a part number.

The SDS-Plus shank has two deep slots and two shallow slots for use with SDS-Plus-drive rotary hammers. These bits cannot be used with SDS-Max-drive rotary hammers. Drill holes using simultaneous rotary and hammering action to break masonry material into tiny granules. This type of bit drills faster and penetrates material with less pressure than rotary-only bits. Also called percussion or impact bits.

For technical drawings and 3-D models, click on a part number.

A built-in stop ensures repeatable drilling depths for installing drop-in anchors. The SDS-Plus shank has two deep slots and two shallow slots for use with SDS-Plus-drive rotary hammers. These bits cannot be used with SDS-Max-drive rotary hammers.

For technical drawings and 3-D models, click on a part number.

Three sharp points allow these bits to drill accurate straight and overlapping holes, even across the grain. The center guide point prevents the bit from wandering. Also known as brad-point bits.

High-speed steel drill bits are stronger and more wear resistant than steel drill bits.

For technical drawings and 3-D models, click on a part number.

The straight flutes and notched point withstand the heavy pressure necessary to penetrate hard steel. These carbide-tipped bits maintain their sharp edges when drilling abrasive material. Because they aren’t as brittle as solid carbide bits, they can be used in less rigid setups, such as a hand-held drill. They are jobbers' length and have the rigidity and length required for most hand-held drilling and machine tool applications.

For technical drawings and 3-D models, click on a part number.

The sharp point allows for gradual penetration to reduce friction and eliminate cracking and chipping when drilling in plastic. These bits are jobbers' length and have the rigidity and length required for most applications.

For technical drawings and 3-D models, click on a part number.

These jobbers'-length bits have the rigidity and length required for most applications. They are designed to make clean holes in abrasive material. Their point keeps the bit centered without a pilot hole.

Uncoated drill bits have three drill points that make clean holes in fiber-reinforced composites without fraying or delaminating the material.

Diamond-coated drill bits are highly wear resistant for drilling in abrasive material. They last longer than uncoated bits.

For technical drawings and 3-D models, click on a part number.

Because softer metal, like aluminum, brass, and bronze, can clog a bit, the flutes on these bits lift chips out of the hole. Also known as slow-spiral drill bits. They are jobbers' length and have the rigidity and length required for most applications.

For technical drawings and 3-D models, click on a part number.

With better heat and wear resistance than high-speed steel, cobalt steel bits can run up to 25% faster and have a longer tool life. Also known as reverse-flute bits, the flutes spiral in the opposite direction of other bits. Use in counterclockwise drilling applications such as removing broken screws. These bits are maintenance length, also known as mechanics’ length. They are shorter and more rigid than jobbers’ bits but longer than short-length bits. The split point keeps the bit centered without a pilot hole.

For technical drawings and 3-D models, click on a part number.

Often called step drill bits, these drill and counterbore holes at the same time. After drilling and counterboring, tap the hole and install your fastener. The body diameter may decrease after multiple sharpenings.

For technical drawings and 3-D models, click on a part number.