These jobbers'-length bits have the rigidity and length required for most applications. Made of cobalt steel, which has better heat and wear resistance than high-speed steel, they can run up to 25% faster and have a longer tool life.

Titanium-nitride (TiN) coated drill bits last longer and can drill at higher speeds than uncoated drill bits.

Drill bits with a split point keep centered without a pilot hole.

For technical drawings and 3-D models, click on a part number.

These jobbers'-length bits have the rigidity and length required for most applications. Made of solid carbide for the highest accuracy and longest tool life, they are harder, stronger, and more wear resistant than high-speed steel, cobalt steel, and carbide-tipped bits. They retain a sharp, hard edge at high temperatures for the best performance on hard and abrasive material. The four-facet point keeps the bit centered without a pilot hole. These bits require rigid toolholding to prevent breakage and should not be used in hand-held drilling applications.

Titanium-aluminum-nitride (TiAlN) coated drill bits are the most wear and temperature resistant for the longest life and highest drilling speeds.

For technical drawings and 3-D models, click on a part number.

The short flutes provide increased rigidity for drilling straighter holes and the long length lets you access hard-to-reach spots. More wear resistant than cobalt steel and high-speed steel, these carbide-tipped bits maintain a sharper, harder edge at high temperatures for excellent performance on abrasive material, such as plastic. Because they aren’t as brittle as solid carbide bits, they can be used in less rigid setups, such as a hand-held drill. A split point keeps the bit centered without a pilot hole.

For technical drawings and 3-D models, click on a part number.

These jobbers'-length bits have the rigidity and length required for most applications. Made of carbide-tipped steel, which has better wear resistance than high-speed steel and cobalt steel, they maintain a sharper, harder edge at high temperatures for excellent performance on abrasive material, such as plastic. Because they aren’t as brittle as solid carbide bits, they can be used in less rigid setups, such as a hand-held drill.

Drill bits with a split point keep centered without a pilot hole.

Drill bits with 135° point angle produce smaller chips than 118° point to prevent clogging.

For technical drawings and 3-D models, click on a part number.

Install the Morse taper shank directly into the tapered spindle on machines such as drill presses and lathes.

For technical drawings and 3-D models, click on a part number.

The SDS-Plus shank has two deep slots and two shallow slots for use with SDS-Plus-drive rotary hammers. These bits cannot be used with SDS-Max-drive rotary hammers. Drill holes using simultaneous rotary and hammering action to break masonry material into tiny granules. This type of bit drills faster and penetrates material with less pressure than rotary-only bits. Also called percussion or impact bits.

For technical drawings and 3-D models, click on a part number.

Drill holes using simultaneous rotary and hammering action to break masonry material into tiny granules. These bits drill faster and penetrate materials with less pressure than rotary-only bits. Also known as percussion or impact bits.

Serrated-point drill bits deliver faster, cooler cutting as well as longer life than standard-point masonry drill bits.

For technical drawings and 3-D models, click on a part number.

Instead of using a hammering action to break up masonry material, these bits drill with rotary action only, requiring more pressure to grind up material. Use with handheld power drills, drill presses, and in hammer drills set to rotary-only mode. Do not use in hammering applications.

For technical drawings and 3-D models, click on a part number.

A more controlled chip removal reduces heat buildup, making these bits good for use on brittle material such as block and brick. Instead of using a hammering action to break up masonry material, they drill with rotary action only, requiring more pressure to grind up material. Use with handheld power drills, drill presses, and in hammer drills set to rotary-only mode. Do not use in hammering applications.

For technical drawings and 3-D models, click on a part number.

Each bit is precisely sized to match the tolerances necessary to achieve maximum holding strength from tapping screws. Use with handheld power drills, drill presses, and hammer drills. The shank has a tang which allows it to fit into a drill press with a tapered spindle.

For technical drawings and 3-D models, click on a part number.

These bits are cut to match a wood screw’s thread and diameter, resulting in a perfect fit for a screw. They produce clean edges when cutting soft and hard wood.

For technical drawings and 3-D models, click on a part number.

The straight flutes and notched point withstand the heavy pressure necessary to penetrate hard steel. These carbide-tipped bits maintain their sharp edges when drilling abrasive material. Because they aren’t as brittle as solid carbide bits, they can be used in less rigid setups, such as a hand-held drill. They are jobbers' length and have the rigidity and length required for most hand-held drilling and machine tool applications.

For technical drawings and 3-D models, click on a part number.

The sharp point allows for gradual penetration to reduce friction and eliminate cracking and chipping when drilling in plastic. These bits are jobbers' length and have the rigidity and length required for most applications.

For technical drawings and 3-D models, click on a part number.

Also known as reverse-flute bits, the flutes spiral in the opposite direction of other bits. Use in counterclockwise drilling applications such as removing broken screws. These bits are jobbers' length and have the rigidity and length required for most applications.

Black-oxide and black-and-gold-oxide drill bits produce less friction than uncoated drill bits.

Drill bits with a split point keep centered without a pilot hole.

For technical drawings and 3-D models, click on a part number.