Access hard-to-reach spots and drill deep holes. The shank has a smaller diameter than the tip, allowing you to drill large holes with machines that have small-capacity chucks.

With better heat and wear resistance than high-speed steel, these cobalt steel bits can run up to 25% faster and have a longer tool life. The shank has a smaller diameter than the tip, allowing you to drill large holes with machines that have small-capacity chucks. A split point keeps the bit centered without a pilot hole. Also known as Silver and Deming bits, they have a 1/2” diameter shank.

Titanium-nitride (TiN) coated drill bits last longer and can drill at higher speeds than uncoated drill bits.

More wear resistant than cobalt steel and high-speed steel, these carbide-tipped bits maintain a sharper, harder edge at high temperatures for excellent performance on hard and abrasive material. The shank has a smaller diameter than the tip, allowing you to drill large holes with machines that have small-capacity chucks. Also known as Silver and Deming bits, they have a 1/2” diameter shank.

Install the Morse taper shank directly into the tapered spindle on machines such as drill presses and lathes.

With better heat and wear resistance than high-speed steel, these cobalt steel bits can run up to 25% faster and have a longer tool life. Install the Morse taper shank directly into the tapered spindle on machines such as drill presses and lathes. A split point keeps the bit centered without a pilot hole.

The SDS-Plus shank has two deep slots and two shallow slots for use with SDS-Plus-drive rotary hammers. These bits cannot be used with SDS-Max-drive rotary hammers. Drill holes using simultaneous rotary and hammering action to break masonry material into tiny granules. This type of bit drills faster and penetrates material with less pressure than rotary-only bits. Also called percussion or impact bits.

The shank has 12 splines for use with a spline-drive rotary hammer. Drill holes using simultaneous rotary and hammering action to break masonry material into tiny granules. These bits drill faster and penetrate material with less pressure than rotary-only bits. Also called percussion or impact bits.

When you encounter rebar, stop drilling and mount one of these bits in your tool. Drill through the rebar, and then resume drilling with your masonry drill bit. The SDS-Plus shank has two deep slots and two shallow slots for use with SDS-Plus-drive rotary hammers set to rotary-only mode. These bits cannot be used with SDS-Max-drive rotary hammers. Do not use in hammering applications.

When you encounter rebar, stop drilling and mount one of these bits in your tool. Drill through the rebar, and then resume drilling with your masonry drill bit. These bits drill holes using rotary action only and should not be used in hammering applications. Use with handheld power drills, drill presses, and in hammer drills set to rotary-only mode.

When connected to a vacuum, these hollow bits can suck up concrete dust while drilling to help meet OSHA standards for silica dust exposure. They can also be used to clean out holes for installing adhesive anchors. The SDS-Max shank has three deep slots and two shallow slots for use with SDS-Max-drive rotary hammers. They cannot be used with SDS-Plus-drive rotary hammers.

Bore clean, flat bottom holes in soft wood, veneer, and laminates. The center guide point prevents the bit from wandering. Also known as Forstner bits.

Multiple outlining teeth bore clean, flat-bottom holes without chipping or splintering your surface—even when cutting across the grain. These bits are excellent for boring straight holes, overlapping holes, and holes on close centers in soft wood, veneer, and laminates. The center guide point prevents the bit from wandering. Also known as multispur bits or Forstner bits.

Also known as spade bits, these have a centering point and two cutting edges for boring holes in hard and soft wood.

An open spiral-flute design clears chips quickly, so these bits can bore smooth, deep holes through construction lumber, railroad ties, and utility poles. Also known as pole or ship auger bits.

Hex/round-shank drill bits have a hex shank that can be cut off to expose a 1/2" round shank.

Steps with progressively larger diameters let you drill a range of sizes with one bit. Also known as step drills.

Titanium-nitride (TiN) coated drill bits last longer and can drill at higher speeds than uncoated drill bits.