Assortments include eight different epoxies in 0.1-oz. packets to handle a variety of small jobs.

Epoxies are the strongest and most weather- and chemical-resistant structural adhesives. They work especially well on metals.

To allow time to adjust and position parts, these epoxies remain workable for at least 90 minutes.

Even when used under water, these adhesives maintain their strength.

These machinable epoxies are mixed with steel, but won’t rust, so they can be used to repair cracks and threaded holes.

Bond most materials without the strong odor of other epoxy adhesives.

Permanently set threaded rods, studs, and rebar in concrete.

Bond new concrete to old concrete, or use this adhesive as a primer on concrete surfaces.

To simultaneously mix and dispense two-part adhesives, attach these mixer nozzles to a dual cartridge.

Dispense two-part adhesives with compressed air. Use these guns only with 3M dual cartridges.

Mix these two-part surface fillers together to repair leaks and cracks as well as to rebuild rough spots in metal.

For use in processing equipment that carries large particles 1/16" in diameter and larger, these ceramic-filled epoxies rebuild and repair surfaces exposed to abrasion from particles, such as pump housings, chute linings, and hoppers.

Repair and rebuild metal surfaces that are exposed to heat. These surface fillers withstand temperatures over 450° F.

To stop leaks in metal tanks and equipment without draining the contents, heat the area with a heat gun or torch to melt the stick and form a permanent seal. The resulting patch can withstand pressure up to 600 psi.

These surface fillers can be used on vertical surfaces without sagging. They repair cracked, worn, and damaged surfaces.

Knead the epoxy-coated patch and resin together to make repairs to pipes, tanks, drums, and containers in the field.

Mix these two-part epoxy surface fillers to create a strong repair in wet environments or underwater.

Patch concrete floors, stairs, and walls with these compounds.

Use these two-part compounds to patch concrete floors, stairs, and walls in cold environments, such as freezers. At room temperature, they cure faster than any of our other concrete patching compounds.

Fill cracks in horizontal, vertical, and overhead concrete surfaces.

Not only do these leveling compounds withstand severe abrasion, wear, and impact, they also stand up to steel wheels and heavy blows without cracking.

Repair sidewalks and factory floors in areas with heavy pedestrian traffic. They can also be used to fill minor depressions and cracks.

Press these putty-like fillers into cracks in wood up to 1/8" wide.

The strongest of the potting compounds, epoxies are rigid and wear resistant. They have excellent chemical and moisture resistance, withstand a wide range of temperatures, and provide excellent electrical insulation.

Formulated to draw heat away from sensitive electronic components, these potting compounds have higher thermal conductivity than standard potting compounds.

Thinner than potting compounds, these rigid and wear-resistant coatings flow easily into small spaces between electrical components. Use them to secure and insulate hardware on printed circuit boards.

These coatings are some of the thickest and most durable on the market. They protect against abrasion and resist moisture and chemicals.

Keep working when temperatures drop—these coatings can be applied in temperatures down to 20° F, when other coatings would fail. Thicker than polyurethane and paint, they protect against abrasion and resist moisture and chemicals.

Longer-lasting than antislip tape, these coatings contain grit to provide traction. They’re good for areas with pedestrian traffic.

These high-traction antislip coatings have zero VOCs and are low odor. They contain grit to provide traction to pedestrian, cart, and hand-truck traffic.

Use these coatings in kitchens, furnace areas, and ships on plastic, metal, wood, and masonry.

These coatings are more durable than our standard coatings for concrete floors. They provide a stain-resistant finish that protects your floors from moisture, chemicals, foot traffic, and hand carts.

Thicker than polyurethane and paint, these coatings have high moisture resistance and protect against abrasion and chemicals.

Cover sharp edges, corners, and weld seams with these thick epoxy coatings for protection against cuts and snags.

Create a washable writing surface.

Enhance, renew, and protect surfaces.

Touch up scratches and wear on powder-coated metal without a primer. Choose the color that matches your equipment—this paint matches some of the most common colors used in powder-coating applications.

Mark traffic lanes, parking lots, and factory floors.

A high concentration of zinc gives these primers excellent corrosion resistance for protecting steel—when exposed to moisture and chemicals, the zinc rusts before the underlying steel can. They’re often used with structural steel.

Use these primers on your surface before antislip coatings to maximize longevity.

These primers stand up to marine exposure and salt spray. Use them to prepare your surface to extend the life of paint and coatings.

These thin primers penetrate deeply into concrete floors to create a hard surface that can then be coated with any urethane or epoxy coating.

Also known as Torr Seal, this sealant forms a rigid bond that seals leaks on vacuum systems or components.