Protect against falls while climbing ladders. These anchor spans have adjustable clamp brackets and secure permanently with an eyebolt on each end. You supply a harness and a carabiner as well as a wire rope grab (sold separately). In the event of a fall, the rope grab stops you within inches.

Also known as horizontal lifelines, these provide fall protection when overhead anchors aren't available. Attach to an anchor point on both sides using the snap hooks, or use the included tie-off adapters for wraparound anchoring. You supply a lanyard and a harness. When used properly, anchor spans meet applicable OSHA requirements.

Also known as vertical lifelines, these are commonly used when working around suspended scaffolding or beams. Attach the snap hook at one end of the rope to an overhead anchor point. You supply a harness as well as a lanyard with rope grab (sold separately). In the event of a fall, the rope grab stops you within inches. When used properly, anchor spans meet applicable OSHA requirements.

This system provides support when lowering workers into and retrieving them from tight spaces. Use the hand-operated winch to control lifting and lowering. You supply a harness.

The system comes with an adjustable mast and a separate portable base. For fixed-base installation, use the wall-mount or floor-mount base—weld or bolt the base to a concrete or steel structure and insert the mast into the opening.

For adequate fall clearance, you must have at least 18 1/2 ft. of clearance. Use in conjunction with a harness for a complete fall-arrest system. When used properly, the system meets applicable OSHA requirements.

Polyester/elastomer lanyards expand and contract with your movements.

Hook-over lanyards have a large snap hook that attaches directly to a rated structure such as a scaffold or pipe to create an anchor point.

Wraparound lanyards loop around a rated structure such as an I-beam and then attach to themselves to create an anchor point.

Made of Kevlar, these lanyards meet ASTM F887 when used with an arc flash-resistant harness. Wrap the lanyard around a rated structure such as an I-beam and then attach it to itself to create an anchor point. For adequate fall clearance, you must have at least 18 1/2 ft. of clearance. Use in conjunction with a harness for a complete fall-arrest system.

Made of steel, these durable lanyards hold up in abrasive and high-heat applications. Attach the large snap hook directly to a rated structure such as a scaffold or pipe to create an anchor point. For adequate fall clearance, you must have at least 20 ft. of clearance. Use in conjunction with a harness for a complete fall-arrest system. When used properly, the system meets applicable OSHA requirements.

For adequate fall clearance, you must have at least 18 1/2 ft. of clearance. Use in conjunction with a harness and an anchor for a complete fall-arrest system. When used properly, the system meets applicable OSHA requirements.

Polyester/elastomer lanyards expand and contract with your movements.

Dual-leg lanyards attach to two anchors at once.

Made of steel, these durable lanyards hold up in abrasive and high-heat applications. For adequate fall clearance, you must have at least 20 ft. of clearance. Use in conjunction with a harness and an anchor for a complete fall-arrest system. When used properly, the system meets applicable OSHA requirements.

Dual-leg lanyard attaches to two anchors at once.

Made of Kevlar, these lanyards meet ASTM F887 when used with an arc flash-resistant harness. For adequate fall clearance, you must have at least 18 1/2 ft. of clearance. Use in conjunction with a harness and an anchor for a complete fall-arrest system. When used properly, the system meets applicable OSHA requirements.

Dual-leg lanyard attaches to two anchors at once.

A quick-stop lanyard must be used when you have less than 18 1/2 ft. of fall clearance as it will stop your fall within a few inches. Use in conjunction with a harness and an anchor for a complete fall-arrest system. When used properly, the system meets applicable OSHA requirements.

Dual-leg lanyard attaches to two anchors at once.

Use the shock-absorbing attachment (sold separately) to increase the capacity of 310-lb. polyester lanyards to 400 lbs.

These lanyards form their own anchor point by attaching directly to a rated structure. A quick-stop lanyard must be used when you have less than 18 1/2 ft. of fall clearance. Use in conjunction with a harness for a complete fall-arrest system. When used properly, the system meets applicable OSHA requirements.

Hook-over lanyard has a large snap hook that attaches directly to a rated structure such as a scaffold or pipe to create an anchor point.

Wraparound lanyard loops around a rated structure such as an I-beam and then attaches to itself to create an anchor point.

Made of heat-resistant Nomex, these harnesses withstand temperatures up to 700° F. They have a D-ring on the back that attaches to a lanyard. A complete fall-arrest system requires a lanyard, a harness, and an anchor. When used properly, the system meets applicable OSHA requirements.

Harnesses have a D-ring that attaches to a lanyard. A complete fall-arrest system requires a lanyard, a harness, and an anchor. When used properly, the system meets applicable OSHA requirements.

Polyester/elastomer harnesses expand and contract with your movements.

Padded harnesses have breathable padding on the back for all-day comfort.

These harnesses have leather-insulated metal components and meet ASTM F887 when used with an arc flash-resistant lanyard. They have a D-ring on the back that attaches to a lanyard. A complete fall-arrest system requires a lanyard, a harness, and an anchor. When used properly, the system meets applicable OSHA requirements.

D-rings on each hip provide a stable working position. Harnesses have a D-ring on the back that attaches to a lanyard for fall protection. A complete fall-arrest system requires a lanyard, a harness, and an anchor. When used properly, the system meets applicable OSHA requirements.

Polyester/elastomer harnesses expand and contract with your movements.

These versatile harnesses have one D-ring on the chest for use with ladder-climbing systems as well as one D-ring on each hip to provide a stable working position. Attach harness to a ladder-climbing system using a carabiner. Harnesses have a D-ring on the back that attaches to a lanyard for fall protection. A complete fall-arrest system requires a lanyard, a harness, and an anchor. When used properly, the system meets applicable OSHA requirements.

With D-rings on the shoulders, these harnesses allow you to raise and lower workers. They have a D-ring on the back that attaches to a lanyard. A complete fall-arrest system requires a lanyard, a harness, and an anchor. When used properly, the system meets applicable OSHA requirements.