For use in processing equipment that carries large particles 1/16" in diameter and larger, these ceramic-filled epoxies rebuild and repair surfaces exposed to abrasion from particles, such as pump housings, chute linings, and hoppers. The size listed is the combined total of the two parts.

These rubber-filled epoxies have excellent wear and impact resistance. Use them to repair and rebuild surfaces such as pump liners, hoppers, and vibrating feeders. The size listed is the combined total of the two parts.

Fill cracks in horizontal, vertical, and overhead concrete surfaces. Surface fillers that have a mix ratio are multi-part fillers. Size listed is the combined total of the parts.

Surface fillers in a pail can repair large areas. They resist abrasion, impact, and chemicals without the use of a sealer. The resin, hardener, and aggregate are in separate containers that can be mixed in the pail.

Stop slow-flowing and weeping leaks in concrete. These crack fillers begin to harden in three to five minutes to create a permanent fix that won't shrink.

Sand fillers are also known as hydraulic cement. Mix with water.

Give new life to damaged and worn concrete floors. These leveling compounds also fill minor depressions and cracks. Apply with a trowel.

Cement compounds are ready for foot traffic in 3 to 4 hours. Add water and mix before applying.

Epoxy compounds resist abrasion for use in high-traffic areas. They’re ready for foot traffic in 8 hours. The resin and hardener are in separate containers that can be mixed in the pail. The size listed is the combined total of the two parts.

These leveling compounds stand up to acid and chemical spills, making them a good choice for corrosive environments. They also withstand steel-wheel traffic and heavy impact. Apply with a trowel. They're ready for foot traffic in 12 hours. The resin and hardener are in separate containers that can be mixed in the pail. The size listed is the combined total of the two parts.

Not only do these leveling compounds withstand severe abrasion, wear, and impact, they stand up to heavy steel-wheel traffic and heavy blows without cracking. Apply with a trowel. They're ready for foot traffic in 12 hours. The resin and hardener are in separate containers that can be mixed in the pail. The size listed is the combined total of the two parts.

Patch concrete floors, stairs, and walls with these compounds.

Mix gypsum compounds with water. They can also be used to anchor bolts, railings, and posts. When used outdoors, apply a sealer (not included) for best results.

Epoxy compounds are three-part compounds consisting of a resin, a hardener, and aggregate in separate containers that can be mixed in the pail. The size listed is the combined total of the parts. They have excellent impact and chemical resistance. Paste compounds are ready for foot traffic in 8-12 hours. Thick liquid compounds are ready for traffic in two hours, and can withstand steel wheels and forklifts.

Cover large sections of damaged concrete with these durable patching compounds. Made up of a resin, hardener, and aggregate, they cover more area than any of our other concrete patching compounds. Use them to fix pitted, worn, and cracked concrete floors, stairs, and loading docks. Compounds resist salt water, oil, and chemicals, and stand up to forklift and truck traffic. The resin, hardener, and aggregate come in separate containers that can be mixed in the pail. Use the squeeze bottle for precision applications, such as in cracks and holes. The size listed is the combined total of the parts.

Use these two-part compounds to patch concrete floors, stairs, and walls in cold environments, such as freezers. At room temperature, they cure faster than any of our other concrete patching compounds. Once cured, they withstand impact, abrasion, and chemicals. The size listed is the combined total of the two parts.

Epoxy compounds are ready for foot traffic in ten minutes and vehicle traffic in two hours. Urethane compounds are ready for foot traffic in five minutes and vehicle traffic in ten minutes. Both can be applied with a trowel when mixed with the included aggregate or used as a self-leveling compound when used alone. Mix in the included pail.

For use when thickness will be less than 2", sand mixes consist of cement and sand. Mix them with water. They are ready for foot traffic at full strength.

Also known as Plaster of Paris, these fillers conceal small cracks, nail holes, and blemishes. Mix with water.

Also known as drywall mud, these joint compounds are ready to use. Apply with drywall tape over seams for a finished appearance.

Repair holes and seal gaps in roofing and gutters. These patching compounds are durable and water resistant.

Apply asphalt compounds to wet or dry surfaces.

Make a temporary repair to cracks in any flat roof. These patching compounds are a powder that forms a thick gel in minutes when poured directly into standing water and rain.

Mix this two-part epoxy—a resin-aggregate blend and a pigmented hardener—to create a grout that resists chemicals, such as acids, alkalies, salt water, and common solvents and cleaners. Its lightweight formula makes this grout easy to spread. Use in horizontal or vertical joints—grout won’t sag or shrink. Apply with a grout float. It can be cleaned up with water when wet; it doesn’t require a sealer once it cures. The size listed is the combined total of the two parts.

Spread patching compounds in dry, wet, and even water-filled holes. Compress them with a tamper or shovel and they are immediately ready for traffic.

Used on ceramic, concrete, and stone floor and wall tiles, grout consists of fine sand, masonry cement, and coloring. Apply with a grout float.

Mix cement grout with water.

Acrylic grout does not require mixing. It resists shrinking, cracking, and staining.

Cut rope to the length you need, pack it in cracks up to 1" wide, and heat with a propane torch (not included). Rope is self-leveling.

Apply these sealants in cold temperatures, on wet surfaces, and even through running water. They are structural sealants that combine the mechanical strength of an adhesive with excellent sealing properties and high flexibility. Sealants are non-sagging, so they won't drip from vertical and overhead surfaces.

Elongation and joint compression/expansion tolerance indicate flexibility—the higher the values are, the more joint movement sealants can sustain. These sealants are good for use between dissimilar materials and in environments with wide temperature fluctuation.

Seal metal-to-metal joints in ductwork. These sealants are non-sagging, so they won't drip from vertical and overhead surfaces.

Also known as glazing compounds, use these sealants to install glass in aluminum, steel, and wood framing. They’re non-sagging, so they won't drip from vertical and overhead surfaces. These sealants are good for use between dissimilar materials and in environments with wide temperature fluctuation. They must be painted after hardening to stand up to UV light.

Even when used under water, these adhesives maintain their strength. The most weather- and chemical-resistant structural adhesives, epoxies tend to work especially well on metals.

The size listed is the combined total of the two parts. For putty adhesives, slice off the required amount, then knead it together to form a moldable adhesive.

WaterWeld and 11800, as well as one-time-use packets, can be applied to wet surfaces or under water.

Grit in these coatings provides traction and fills hairline cracks. Coatings form a weather- and water-resistant seal to protect and revitalize asphalt surfaces. Apply with a squeegee or brush.